Abstract:In recent years, square hollow section (SHS) joints with concrete-filled square hollow section (CFSHS) chords have increasingly been used in truss bridges where the fatigue life reliability is a critical issue. In this paper, a finite element analysis was performed to investigate the SCFs in SHS-CFSHS T-joints under in-plane bending in the brace, axial force in the chord and in-plane bending in the chord. The finite element models were developed and validated with experimental results. Then a parametric study was conducted with a reasonable range of three key non-dimensional parameters, i.e., β (width ratio between brace and chord), 2γ (width–to–wall thickness ratio of the chord) and τ (wall thickness ratio between brace and chord). Consequently, the stress concentration factor formulae for the fatigue design of SHS-CFSHS T-joints were proposed through multiple regression analysis. For in-plane bending in the brace, the maximum stress concentration factors were found at lines B and C for thick-walled chords (2γ = 25.0), while the stress concentration factors at all the lines need to be checked for thin-walled chords (2γ < 16.0). Under axial force in the chord and in-plane bending in the chord, only stress concentration factors at lines C and D needed to be considered. A comparison of stress concentration factors between SHS-SHS and SHS-CFSHS joints showed reductions of 10~26% and 14~31% in stress concentration factors in SHS-CFSHS joints under axial force in the brace and in-plane bending in the brace, respectively. In addition, it showed a general increase in stress concentration factors in SHS-CFSHS joints under axial force and in-plane bending in the chord. This reduction is attributed to the reduction in chord face deformation benefiting from the in-filled concrete. Meanwhile, the stress concentration factors caused by loads in the chord are much lower than those caused by loads in the brace. This work complements earlier studies on SHS-CFSHS T-joints under axial force.

Effects of Chord Pre-Load on Strength of CHS X-joints Stiffened with External Ring Stiffeners and Gusset Plates

Ultimate Bearing Capacity of CHS X-joints Stiffened with External Ring Stiffeners and Gusset Plates Subjected to Brace Compression

Experimental study of the static behavior of tubular N-joints

An Axial Semi-Rigid Connection Model for Cross-Type Transverse Branch Plate-to-chs Joints

Parametric Study of In-Plane Ultimate Bearing Capacity of CFST Truss Rib Arch Bridge

Experimental and numerical study on compressive behavior of welded hollow spherical joints with external stiffeners

Approach for Analyzing the Ultimate Strength of Concrete Filled Steel Tubular Arch Bridges with Stiffening Girder

Axial Capacity of CHS T-Joints Reinforced with Welded External Stiffeners Under Load

Study Of Mechanical Performance Of Concrete-Filled Steel Tubular Joints

Influence of Chord Stress on Axial Strength of Rectangular Tubular TX- and XX-joints

Mechanical Behaviour of Concrete-Filled CHS Connections Subjected to In-Plane Bending

Experimental Study on the Axial Compressive Strength of Vertical Inner Plate Reinforced Square Hollow Section T-joints

Full-scale experimental research on tubular N-joints of square chords with circular braces

Experimental investigation of SCF distribution for thin-walled concrete-filled CHS joints under axial tension loading

Behaviour of CFDST chord to CHS brace composite K-joints: Experiments

Expressions for Stress Concentration Factors for T-Joints of Hollow and Concrete-Filled Square Cross-Sections for In-Plane Axial and Bending Loads

Behaviour of high-strength CFDST chord to CHS brace T-joint: Experiment

Design of concrete filled tubular CHS T-joints under in-plane bending

Experimental and numerical study on static behaviour of uniplanar CFDST-CHS T-joints

Load Introduction and Transfer Mechanism of K-type CFST Circular Section Connections

Design Of Concrete-Filled Steel Tubular Chs Connections In Tension