Abstract:Carbon fiber reinforced resin matrix composites were toughened by the continuous and randomly distributed carbon nanotubes (CNTs), which were fabricated by floating catalytic chemical vapor deposition (FCCVD) method. Toughening was achieved by deploying CNT film of different a real density as interleaves in the carbon fiber reinforced composites. Double cantilever beam (DCB) specimens were adopted in both quasi-static and dynamic fracture tests. The electromagnetic Hopkinson bar was applied to achieve pure type I fracture mode at high loading speeds of 15 m/s and 24 m/s. The effects of CNTs and loading rates on the Mode I fracture toughness of the composites are investigated. It is shown that fracture toughness approaches a maximum value of 626 J/m(2) under quasi-static loading, only if a 2-layered CNT film is being applied as an interleave, which is twice that of the neat composite (without CNT interleaves). Under dynamic loading, all the specimens either with or without CNTs show increases in the fracture toughness with the increase in loading rate. Different from the results of quasi-static tests, under dynamic loading conditions, the fracture toughness increases monotonously and approaches to a maximum value of 1380 J/m(2) when 40-layered CNT film was applied, which is a remarkable increase of 140% if compared with that of the neat specimen. A detailed analysis of mechanisms responsible for the ameliorating effects of CNTs interleaves is carried out. It is believed that strengthening of interfaces between carbon fibers and matrix, deformation of resin and detachment of CNTs from the matrix are the main factors responsible for this effect.

Compressive residual thermal stress induced crack deflection in carbon nanotube-doped carbon/carbon composites

Influence of Inter-tube Connections on the Stress-Strain Behavior of Nanotube-Polymer Composites: Molecular Dynamics

Impact of Carbon Nanotube Defects on Fracture Mechanisms in Ceramic Nanocomposites

Deep Understanding of Typical CNT Morphology on the Microstructure and Mechanical Properties of 2D Carbon/carbon Composites

Tensile Mechanical Behaviors of High Loading of Carbon Nanotube/Epoxy Composites via Experimental and Finite Element Analysis

Reinforcing effects of carbon nanotube on carbon/carbon composites before and after heat treatment

Fatigue Strengthening of Carbon/carbon Composites Modified with Carbon Nanotubes and Silicon Carbide Nanowires

Compressive and Interlaminar Shear Properties of Carbon/carbon Composite Laminates Reinforced with Carbon Nanotube-Grafted Carbon Fibers Produced by Injection Chemical Vapor Deposition

Effect of Carbon Nanotubes Electrophoretically-Deposited on Reinforcing Carbon Fibers on the Strength and Toughness of C/SiC Composites

Influence of carbon nanotube content on microstructures and mechanical properties of carbon/carbon composite

Residual Thermal Stresses in Carbon/carbon–zr–ti–c Composites and Their Effects on the Fracture Behavior of Composites with Different Preforms

The Rate-Dependent Mechanical Behavior of CNT-reinforced Aluminum Matrix Composites under Tensile Loading

Effects of Loading Rates on Mode I Interlaminar Fracture Toughness of Carbon/epoxy Composite Toughened by Carbon Nanotube Films

Study on Mechanical Properties of Carbon Nanotube Reinforced Composites

Multiscale Analysis of Fracture of Carbon Nanotubes Embedded in Composites

Critical Evaluation of the Stiffening Effect of Carbon Nanotubes in Composites

Effects of CNT Microstructural Characteristics on the Interfacial Enhancement Mechanism of Carbon Fiber Reinforced Epoxy Composites Via Molecular Dynamics Simulations

High-strength and toughness carbon nanotube fiber/resin composites by controllable wet-stretching and stepped pressing

Frictional Sliding of Microcracks under Compression

Crack Growth Resistance Of Natural Rubber Reinforced With Carbon Nanotubes

Augmenting the fracture toughness and structural health monitoring capabilities in Kevlar/epoxy composites using carbon nanotubes