Abstract:Pure copper is very soft, however, hardening the pure copper with most strengthening mechanisms leads to a significant reduction in electrical conductivity. Grain refinement is a better strengthening mechanism to maintain high enough electrical conductivity. Plastic deformation at room temperature followed by post-annealing is one of the best methods to achieve fine-grained metals and alloys. In this research, the high-temperature annealing behavior of cold-rolled electrolytic tough-pitch (ETP) copper sheets was studied. 90 % asymmetric cold rolling followed by high-temperature post-annealing at 673 K for 1, 2, 5, 10, 30, 60, and 120 min were applied on the copper. The microstructure was significantly changed with increasing annealing time from 1 to 2 min owing to full recrystallization. With increasing the annealing duration, the grain size is increased. The formation of equiaxed grains with a smaller size (∼9 μm) compared to the full-annealed (initial) sample (∼68 μm) is observed after the longest time of post-annealing (120 min) due to the pinning effect of Cu2O particles. The post-annealed copper sheets processed by asymmetric rolling (in this work) exhibited a more homogeneous microstructure through the thickness compared to the symmetric rolling due to more uniform stored strain energy. The results showed that the first deformed grains that undergo recrystallization during post-annealing are Goss-oriented grains. With an increase in the post-annealing time, the S and Copper components were eliminated and a strong Cube and P texture orientations were formed. Interestingly, after 1 min of post-annealing, the yield and tensile strength enhanced to 410.2 MPa and 418.6 MPa owing to the annealing hardening phenomenon. The hardness and strength reached a constant value after the post-annealing for 10 min and above. With increasing the post-annealing duration, the central area of fracture surfaces (consisting of ductile dimples) became larger and the outer region (consisting of flat surfaces and shear dimples) became smaller, showing a shift towards perfect ductile fracture. With the increase of post-annealing time from 1 min to 120 min, the electrical conductivity was increased from 77.6 to 97.5 %IACS. The presence of the Cube texture increased the electron mobility compared to the P orientation, by reducing the mean distance that they can travel without scatter. From the obtained results, it can be concluded that the asymmetric cold rolling followed by high-temperature post-annealing is capable of strength improvement and maintaining electrical conductivity in copper.

Effect of Stress Relief Annealing on Microstructure, Mechanical Properties, and Residual Stress of a Copper Sheet in the Constrained Groove Pressing Process

Effect of cryogenic impact deformation and subsequent annealing on microstructure and microhardness of pure copper

The effect of microstructure parameters on the residual stresses in the ultrafine-grained sheets

Effect of High Temperature-High Pressure Treatment on Microstructure and Mechanical Properties of Cu-Cr Alloy

Annealing Effect of High-Density Pulsed Electric Current Treatment on Cold-Rolled 6061 Aluminum Alloy

Effect of grain refinement on mechanical and electrochemical properties of severely deformed pure copper through equal channel angular pressing

Effects of Normal Stress, Surface Roughness, and Initial Grain Size on the Microstructure of Copper Subjected to Platen Friction Sliding Deformation

Microstructure and Texture of Pure Copper under Large Compression Deformation and Different Annealing Times

A profound study of damage behavior for Al 2024-T3 alloy worksheet produced by constrained groove pressing in the superior practical condition

Enhancing strength while preserving elongation: A study on copper after accumulative skin pass rolling

Effect of Cold Pressing Deformation on Microstructure and Residual Stress of 7050 Aluminum Alloy Die Forgings

Effects of residual stress on the mechanical properties of copper processed using ultrasonic-nanocrystalline surface modification

Characterisation of Microstructure, Texture and Mechanical Properties of Pure Aluminium Sheets Severely Deformed by Constrained Groove Pressing and Subsequent Cold Rolling

High-temperature annealing behavior of cold-rolled electrolytic tough-pitch copper

Microstructure and Mechanical Properties of Ultrafine-Grained Copper by Accumulative Roll Bonding and Subsequent Annealing

EFFECT OF DIFFERENT STRAIN ROUTES ON MECHANICAL PROPERTIES AND MICROSTRUCTURE OF COPPER

Strain effects on the wear rate of severely deformed copper

Quasi In Situ Study on the Slipping Behavior and Residual Stress of Copper Strip

Microstructure and fretting wear behaviour of gradient-structured Cu sheets prepared by plastic flow machining

Influence of Gradual Stress Relieving on the Microstructure, Texture Development, Grain Structure and Orientation of the Hot-Rolled Ti6Al4V-5Cu Alloy.

Microstructure, texture and mechanical properties of pure copper processed by ECAP and subsequent cold rolling