Abstract:Solar cells based on kesterite-type $Cu_2ZnSnS_4$ (CZTS) thin films were fabricated using a chemical route to prepare the $CZTS$ films, consisting in sequential deposition of $Cu_2SnS_3$ (CTS) and $ZnS$ thin films followed by annealing at $550^\circ C$ in nitrogen atmosphere. The $CTS$ compound was prepared in a one-step process using a novel chemical procedure consisting of simultaneous precipitation of $Cu_2S$ and $SnS_2$ performed by diffusion membranes assisted $CBD$ (chemical bath deposition) technique. Diffusion membranes were used to optimize the kinetic growth through a moderate control of release of metal ions into the work solution. As the conditions for the formation in one step of the $Cu_2SnS_3$ compound have not yet been reported in literature, special emphasis was put on finding the parameters that allow growing the $Cu_2SnS_3$ thin films by simultaneous precipitation of $Cu_2S$ and $SnS_2$. For that, we propose a methodology that includes numerical solution of the equilibrium equations that were established through a study of the chemical equilibrium of the system $SnCl_2$, $Na_3C_6H_5O_7\cdot 2H2O$, $CuCl_2$ and $Na_2S_2O_3\cdot5H_2O$. The formation of thin films of $CTS$ and $CZTS$ free of secondary phases grown with a stoichiometry close to that corresponding to the $Cu_2SnS_3$ and $Cu_2ZnSnS_4$ phases, was verified through measurements of X-ray diffraction $(XRD)$ and Raman spectroscopy. Solar cell with an efficiency of $4.2%$, short circuit current of $16.2 mA/cm^2$ and open-circuit voltage of 0.49 V was obtained.

Fabrication of Cu2ZnSnS4 Thin Films Based on Facile Nanocrystals-Printing Approach with Rapid Thermal Annealing (RTA) Process

Molecular-solution Printing of Cu2ZnSnS4 (CZTS) Thin Film

Cu2ZnSnS4 Thin Film Fabricated by the Calcinated Nanocrystals

Influences of Rapid Thermal Annealing on Cu2ZnSnS4 Thin Film Fabricated by Spraying Approach

Fabrication of Cu 2 ZnSnS 4 thin films using oxides nanoparticles ink for solar cell

Low-cost Fabrication of Cu 2 ZnSnS 4 Thin Films for Solar Cell Absorber Layers

Facile Fabrication of Cu2ZnSnS4 Thin Film Based on a Novel Metal–salt Precursor Printing Route

In situ fabrication of Cu2ZnSnS4 nanoflake thin films on both rigid and flexible substrates

Preparation of Cu2znsns4 Film by Printing Process for Low-Cost Solar Cell

Study on the Optimization of Cu-Zn-Sn-O to Prepare Cu2ZnSnS4 Thin Film via a Nano Ink Coating Method

Preparation And Characterization Of Cu2znsns4 Thin Films And Solar Cells Fabricated From Quaternary Cu-Zn-Sn-S Target

Fabrication of Cu2ZnSnS4 (CZTS) Absorber Films Based on Different Compound Targets

Optical and Electrical Properties Study of Sol-Gel Derived Cu2znsns4 Thin Films for Solar Cells

Synthesis and Characterization of Cu2znsnse4 Nanocrystals Prepared by One Pot Route

Fabrication of solar cells based on $Cu_2ZnSnS_4$ prepared from $Cu_2SnS_3$ synthesized using a novel chemical procedure

Influences of synthesis conditions on chemical composition of Cu 2ZnSnS4 nanocrystals prepared by one pot route

CZTS nanocrystals: a promising approach for next generation thin film photovoltaics

Synthesis and Characterization of Cu 2 ZnSnS 4 from Cu 2 SnS 3 and ZnS Compounds

Fabrication of Cu2ZnSn(S,Se)4 absorber films by selenization of different Cu2ZnSnS4 nanocrystal coatings

Nanoparticle Based Preparation Method of Cu_2ZnSn(SSe)_4 Thin Films

Synthesis and characterization of CZTS and Cu2-xAgxZnSnS4 thin films for the application of solar cells