Abstract:The AlN/BN composite ceramic, fabricated via hot-press sintering, exhibits obvious anisotropy due to the establishment of directional alignment of h-BN. However, the variation and influence mechanisms of bending strength (σ) and thermal conductivity (λ) are remain unclear in different directions, which greatly limit the application of AlN/BN composite ceramics. In this paper, the effects of h-BN content on phase composition, microstructure and anisotropy of AlN/BN composite ceramics are discussed in detail. The results reveal that AlN/BN composite ceramics have three directions: perpendicular (⊥), longitudinal parallel (∥), and lateral parallel (≡) to the hot-pressing direction. The content of h-BN is a crucial factor affecting the anisotropy of AlN/BN composite ceramics. h-BN enhances the thermal conductivity in the ∥ and hinders the thermal conductivity in the ⊥. With the increase in h-BN amount, λ∥ rises gradually, while λ⊥ gradually falls. When the mass percentage of h-BN and AlN is 25 % (AB25), the λ∥ is as high as 90 W m−1 K−1, which is about 2.25 times that of λ⊥. In terms of mechanical properties, σ ≡ and σ ⊥ first increase and then decrease, while σ ∥ only decreases. This is attributable to h-BN being effective in enhancing mechanical properties by inhibiting crack propagation in the ⊥ and ≡ direction, while the promotion of crack propagation leads to a decrease in mechanical properties in the ∥ direction. σ ≡ reaches the highest values (σ ≡ = 460.2 MPa) at an h-BN amount of 10 % (AB10), which is about 1.19 and 2.04 times that of σ ⊥ and σ ∥, respectively, and 22.1 % higher than that of AB0.

Effect of the Starting AlN Content on the Phase Formation and Property of the Novel In-Situ Fabricated X-SiAlON/BN Composites

Effects of AlN content on phase composition, microstructure and mechanical properties of DN-based composite ceramics

Effects of AlN Content on Phase Composition, Microstructure and Mechanical Properties of BN-based Composite Ceramics

Effect of aln content on the microstructure and mechanical properties of bn-based composites

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

Mechanical and thermal properties of in situ AlN/Al-12Si composite fabricated by laser powder bed fusion

Fabrication and properties of AL2O3-SiAlON composites with nano-sized t- and h-BN dispersion

Effect of hexagonal boron nitride content on the anisotropy of hot-press-sintered AlN/BN composite ceramics

Improvement in mechanical properties in AlN-h-BN composites with high thermal conductivity

Effect of AlN content on the properties and microstructure of pressureless-sintered Al 2 O 3-AlN composites

Fabrication of High Strength α-SiAlON/BN Composition Ceramics by Hot Pressing

Effects of Aln Content on the Thermal Properties and Thermal Shock Resistance of Bn Matrix Composite Ceramic

High-performance Aluminum-Based Matrix Composites Reinforced with High Content of Boron Nitride Nanosheets

Effect of impregnating and heat treatment on microstructure and properties of pressureless sintering AlN/h-BN composite ceramics

Effect of the BN Content on the Thermal Shock Resistance and Properties of BN/SiO2 Composites Fabricated from Mechanically Alloyed SiBON Powders

Fabrication and Properties of SiO2-BN-Si3N4 Composites

Carbon‐content‐dependent Phase Composition, Microstructural Evolution, and Mechanical Properties of SiBCN Monoliths

SiC and ZrN Nano-Particulate Reinforced AlON Composites: Preparation, Mechanical Properties and Toughening Mechanisms

Effect of BN on Sintering Property and Titanium Melt Erosion Resistance of AlN Refractories

Effect of nickel content on the sintering behavior, mechanical and dielectric properties of Al2O3/Ni composites from coated powders

Microstructure elaboration and mechanical properties of AlN_p/4032Al composite