Abstract:The insufficient ionic conductivity of oxide-based solid electrolytes and the large interfacial resistance between the cathode material and the solid electrolyte severely limit the performance of room-temperature all-solid-state sodium rechargeable batteries. A NASICON solid electrolyte Na3.4Zr1.9Zn0.1Si2.2P0.8O12, with superior room-temperature conductivity of 5.27 × 10–3 S cm–1, is achieved by simultaneous substitution of Zr4+ by aliovalent Zn2+ and P5+ by Si4+ in Na3Zr2Si2PO12. The bulk conductivity and grain boundary conductivity of Na3.4Zr1.9Zn0.1Si2.2P0.8O12 are nearly 20 times and almost 50 times greater than those of pristine Na3Zr2Si2PO12, respectively. The FeS2||polydopamine-Na3.4Zr1.9Zn0.1Si2.2P0.8O12||Na all-solid-state sodium batteries, with a polydopamine modification thin layer between the solid electrolyte and the cathode, maintain a high reversible capacity of 236.5 mAh g–1 at a 0.1 C rate for 100 cycles and a capacity of 133.1 mAh g–1 at 0.5 C for 300 cycles, demonstrating high performance for all-solid-state sodium batteries.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsenergylett.0c01432?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsenergylett.0c01432</a>.Experimental section; XRD, NPD, SEM, and EIS measurements for different solid electrolyte materials; STEM-EDS and DC polarization measurement for Zn0.1 sample; EDS measurement for Zn0.1 sample before and after contact with sodium; unit cell parameters of different solid electrolyte materials; structural parameters of different solid electrolyte materials; BVEL analysis and the comparison of bottleneck sizes; conductivities, activation energies, and relative densities of different solid electrolyte materials; FTIR measurement for Zn0.1 pellet with and without PDA layer; charge–discharge curves of FeS2||Zn0.1||Na all-solid-state battery; comparison of conductivities and battery performances reported in the literature and in this work; cross-sectional images of the cathode/electrolyte interface before and after cycling (<a class="ext-link" href="/doi/suppl/10.1021/acsenergylett.0c01432/suppl_file/nz0c01432_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Ca-doped Na2Zn2TeO6 layered sodium conductor for all-solid-state sodium-ion batteries

Enhanced ionic conductivity of Cu-doped NASICON solid electrolyte for solid-state sodium batteries

Layered sodium titanate with a matched lattice: a single ion conductor in a solid-state sodium metal battery

Calcium Doped NASICON electrolyte with Graphite Coating for Stable All‐solid‐state Sodium Metal Batteries

Aliovalent dual element co-assisted strategy to enhance ionic conductivity and stability of NASICON-type solid electrolyte for all-solid-state sodium batteries

Mg-doped NASICON-type electrolyte for rechargeable solid-state sodium-ion batteries

Bi2O3-Assisted Sintering of Na3Zr2Si2PO12 Electrolyte for Solid-State Sodium Metal Batteries

Increase ionic conductivity of a Zn2+/F− synergy Na3Zr2Si2PO12 solid electrolyte for sodium metal batteries

Enabling ultrafast lithium-ion conductivity of Li2ZrCl6 by indium doping

NASICON-structured Na3.1Zr1.95Mg0.05Si2PO12 solid electrolyte for solid-state sodium batteries

Rare Earth Oxide-Assisted Sintered NASICON Electrolyte Composed of a Phosphate Grain Boundary Phase with Low Electronic Conductivity

Entropy Tuning Stabilizing P2‐Type Layered Cathodes for Sodium‐Ion Batteries

Enhancing Na-ion conducting capacity of NASICON ceramic electrolyte Na3.4Zr2Si2.4P0.6O12 by NaF sintering aid

Ultrastable All-Solid-State Sodium Rechargeable Batteries

LaCl3-based sodium halide solid electrolytes with high ionic conductivity for all-solid-state batteries

Sandwiched composite electrolyte with excellent interfacial contact for high-performance solid-state sodium-ion batteries

Sc-doping in Na3Zr2Si2PO12 electrolytes enables preeminent performance of solid-state sodium batteries in a wide temperature range

Zirconia-free NaSICON solid electrolyte materials for sodium all-solid-state batteries

Improving High-Voltage Cycling Stability and High-Rate Capability of Sodium-Ion Layered Cathode Oxides through Trace Amounts of Low-Valence Metals

Enabling Rapid and Stable Sodium Storage via a P2-Type Layered Cathode with High-Voltage Zero-Phase Transition Behavior

A Well-Designed P2-Na0.67Mn0.85Al0.05Zn0.1O< Sub>2 Cathode for Superior Sodium-Ion Batteries