Abstract:The impact of Zn on the mechanical properties and corrosion resistance of Al-Mg-Si alloys with high Cu contents was studied through microstructure analysis and accelerated corrosion testing. The age-hardening response of the alloy improved with the addition of trace Zn, and the poor corrosion resistance caused by high Cu content was overcome. Intergranular corrosion susceptibility (IGC) decreased and then increased with increasing Zn content. Al-Mg-Si-Cu alloys that contain 0.5 wt.% Zn possessed the best corrosion resistance. Zn decreased the potential difference between the matrix and the Al(Mn, Fe)Si phases according to scanning Kelvin probe force microscopy (SKPFM) tests, which reduced the driving force of corrosion in the alloy. Additionally, the addition of Zn promoted discontinuous precipitation at the grain boundaries, which was conducive to enhancing the IGC resistance. However, excessive Zn (1.0 wt.%) promoted the diffusion of more solute atoms near the grain boundaries to the grain boundaries, which coarsened the precipitated phase at the grain boundaries and shortened the interphase distance. Moreover, as the width of the PFZ increased, the concentration of solute atoms decreased, and the potential difference between the precipitated phase and the PFZ increased, leading to more severe IGC behavior. Therefore, an appropriate Zn content was beneficial for improving the corrosion properties and age-hardening response of Al-Mg-Si-Cu alloys.

Influence of Zn Contents on Precipitation and Corrosion of Al-Mg-Si-Cu-Zn Alloys for Automotive Applications

Influence of Minor Zn Addition on Precipitation Behavior and Intergranular Corrosion Properties of Al-Mg-Si Alloy

Effect of Trace Zn on the Mechanical Properties and Corrosion Behavior of Al-Mg-Si Alloys with High Cu

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Precipitation hardening and intergranular corrosion behavior of novel Al–Mg–Zn(-Cu) alloys

The influences of Zn、Sb、Ti、Zr on the corrosion of ZL114A alloy

The effect of Zn content on the microstructure and mechanical properties of the Al-mg-Si alloy

Effects of grain boundary chemistry and precipitate structure on intergranular corrosion in Al-Mg-Si alloys doped with Cu and Zn

Investigation on the microstructural evolution and corrosion behaviors of Zn-microalloyed Al-Cu-Li alloys

Effect of Zn Concentration on the Microstructure and Mechanical Properties of Al-Mg-Si-Zn Alloys Processed by Gravity Die Casting

Effect of Zn Content on the Mechanical Properties, Damping Capacity, and Intergranular Corrosion of Al-Mg-Zn-Sc Alloys

Influence of Mg Content on the Corrosion Behavior and Precipitation of Aged Al-Cu-Li-xMg Alloys

Effects of Cu content on the precipitation process of Al–Zn–Mg alloys

Effect of Cu Content and Zn/Mg Ratio on Microstructure and Mechanical Properties of Al–Zn–Mg–Cu Alloys

Enhanced Corrosion Performance by Controlling Grain Boundary Precipitates in a Novel Crossover Al-Cu-Zn-Mg Alloy by Optimizing Zn Content

Influence of Zn Addition on the Aging Precipitate Behavior and Mechanical Properties of Al-Cu-Li Alloy

Aging Behavior and Precipitate Characterization of Zn-rich Al–Zn–Mg–Cu Alloys with Various Mg and Cu Contents

Influence of Grain-Boundary Pre-Precipitation and Corrosion Characteristics of Inter-Granular Phases on Corrosion Behaviors of an Al–Zn–Mg–Cu Alloy

Effect of Zn on Precipitation Evolution and Mechanical Properties of a High Strength Cast Al-Li-Cu Alloy

Effects of Zn Addition on the Aging Behavior and Mechanical Properties of Mg-8Al-2Sn Wrought Alloy

Correlations among stress corrosion cracking, grain-boundary microchemistry, and Zn content in high Zn-containing Al–Zn–Mg–Cu alloys