Abstract:In this paper, mechanical properties and microstructures of the cast and extruded Al-xCu-1Li-0.4Mg–1Zn-0.1Zr alloys (x = 2.0, 3.0, 4.0, 4.5, 5.5, 6.5 wt%) were investigated. The results showed that the as-cast micrographs of alloys with different Cu content primarily consist of dendritic α-Al grains, and the intermetallic phases at the grain boundaries were Cu and Zr rich phases. After solution treatment, no recrystallization took place in extruded alloys, and the alloys mainly represented mixed textures composed of <111> and <100> fibers. Cu significantly affected the precipitation behavior of the extruded alloys. Only T1 (Al2CuLi) phases were observed in T6 (aging at 175 °C for 32 h) and T8 (3% pre-strain followed by aging at 150 °C for 32 h) treated alloy with 2 wt% Cu. Further increasing Cu contents (4.5 and 6.5 wt%) enabled the co-precipitation of T1 and θ' (Al2Cu) phases, as well as increased their density. In addition, the microstructures of grain boundaries of alloys with different Cu content showed dramatic differences. T1 phases precipitated at the grain boundaries of alloy containing 2 wt% Cu, while rare precipitation of T1 phases was observed at the grain boundaries of alloy with 6.5 wt% Cu. The yield strength (YS) of the alloys increased with the Cu content and the elongation (EL) showed an opposite trend. A good combination of ultra-high strength (YS = 684 MPa, ultimate tensile strength = 726 MPa) and ductility (EL = 6.3%) was obtained in T8 treated alloy containing 4.5 wt% Cu. The presence of the undesired coarse T2 (Al6CuLi3) phases at the grain boundaries resulted in the premature failure of the high Cu content alloys.

Effects of Cu content on the precipitation process of Al–Zn–Mg alloys

Aging Behavior and Precipitate Characterization of Zn-rich Al–Zn–Mg–Cu Alloys with Various Mg and Cu Contents

Effects of Cu Addition on Aging Precipitation Behavior of Cast Mg-3Zn-xCu-0.6Zr Magnesium Alloys

Effects of Cu and Al on the Crystal Structure and Composition of Η (mgzn 2 ) Phase in Over-Aged Al–Zn–Mg–Cu Alloys

Effect of Cu Content on Precipitation and Age-Hardening Behavior in Al-Mg-Si-xCu Alloys

Effect of Cu Content and Zn/Mg Ratio on Microstructure and Mechanical Properties of Al–Zn–Mg–Cu Alloys

Effect of Cu content on microstructures and properties of Al-Mg-Si-Cu alloys

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Effects of Mg/Zn ratio and pre-aging on microstructure and mechanical properties of Al–Mg–Zn–Cu alloys

Study on properties and precipitation behavior of 6000 series alloys with high Mg/Si ratios and Cu contents

Co-precipitation of T′ and η′ phase in Al-Zn-Mg-Cu alloys

Effect of Cu addition on precipitation and age-hardening response of an Al-15%Mg2Si alloy

Effect of Cu content on the mechanical properties of an Al–Cu–Mg–Ag alloy

Influence of Mg content on ageing precipitation behavior of Al-Cu-Li-x alloys

Influence of Mg Contents on Aging Precipitation Behavior of Al–3.5Cu–xMg Alloy

Effects of Cu Addition on the Microstructural Evolution during Ageing of 6000 and 7000 Al Alloys

Effect of Mg content on Cu precipitation behavior in Al-Cu-Mg ternary alloy by molecular dynamics simulation

Aging precipitation characteristics and tensile properties of Al–Zn–Mg–Cu alloys with different additional Zn contents

Effect of Zn and Mg Content on Microstructure and Properties of Al-Zn-Mg-Cu High Strength Aluminum Alloys

Influence of Zn Addition on the Aging Precipitate Behavior and Mechanical Properties of Al-Cu-Li Alloy

Influence of Mg and Cu on Precipitation Behaviors and Mechanical Properties of Al-Si Alloys