Abstract:The hole injection layer (HIL) plays a significant role in determining the performances of organic light-emitting diodes (OLEDs), especially when hole transport materials with deep highest occupied molecular orbital levels (HOMOs) are employed. Intensive efforts have been devoted to exploring novel hole injection materials with good solution-processing abilities in recent years. In this study, the solution-processed molybdenum trioxide (s-MoO3) is prepared via an ultra-facile method. Three different s-MoO3 layers prepared by three different methods, viz. layers annealed at 150 degrees C (s-MoO3 (150)), layers annealed at 150 degrees C and then processed in UV-ozone for 15 min (s-MoO3 (150, UVO)), and layers processed in UV-ozone for 15 min without annealing (s-MoO3 (UVO)), are obtained to investigate their influences on hole injection. The device with the s-MoO3 (150) layer has the lowest current density and the largest driving voltage, showing poor hole injection ability. In contrast, with the s-MoO3 (150, UVO) layer as HIL, the OLED produces a greatly enhanced current and sharply reduced driving voltage, comparable to the device using vacuum-evaporated MoO3. Similar results are obtained for the device with the s-MoO3 (UVO) film, suggesting that high-temperature annealing is not essential for the s-MoO3 film with UV-ozone treatment. Hole injection efficiencies of MoO3 films are quantitatively characterized by analyzing the space-charge-limited current of hole-only devices; the hole injection efficiencies of s-MoO3 (150, UVO) and s-MoO3 (UVO)-based devices are similar to 0.1, far exceeding that of the s-MoO3 (150)-based device (10(-5)). XPS analysis is performed to detect the impact of the above treatments on the surface electronic properties of the s-MoO3 films. A typical characteristic of Mo5+ species is obtained for the s-MoO3 (150) film and a high-binding-energy shoulder appears in the O 1s peak of the s-MoO3 (150) film, indicating the existence of oxygen vacancies and oxygen adsorbed at the surface of s-MoO3 (150) film. When UV-ozone treatment is applied to this s-MoO3 (150) film, it produces a decrease of Mo5+ state and elimination of oxygen-rich adsorbates, resulting in MoO3 stoichiometry similar to that of the vacuum-evaporated MoO3 film. Consequently, a maximum current efficiency of 48.3 cd.A(-1) is realized with the optimized UV-ozone treated s-MoO3 HIL. It This UV-ozone treated s-MoO3 should have widespread applications in low-cost solution-processed OLEDs as an excellent hole injection layer.

Aqueous Solution-Processed Molybdenum Oxide As an Efficient Hole Injection Layer for Flexible Quantum Dot Light Emitting Diodes

Efficient Hole Injection of MoO<sub>x</sub>-Doped Organic Layer for Printable Red Quantum Dot Light-Emitting Diodes

Highly Efficient All-Solution-Processed Quantum Dot Light-Emitting Diodes Using MoOx Nanoparticle Hole Injection Layer

Record High External Quantum Efficiency of 20% Achieved in Fully Solution-Processed Quantum Dot Light-Emitting Diodes Based on Hole-Conductive Metal Oxides

Solution-processed MoOx Hole Injection Layer Towards Efficient Organic Light-Emitting Diode

Efficient Organic-Inorganic Hybrid Hole Injection Layer for Organic Light-Emitting Diodes by Aqueous Solution Doping

Use of Hybrid PEDOT:PSS/Metal Sulfide Quantum Dots for a Hole Injection Layer in Highly Efficient Green Phosphorescent Organic Light-Emitting Diodes

Solution-processable copper-doped molybdenum oxide films as hole injection interfacial layer in polymer light-emitting diodes

A Low-Temperature-annealed and UV-ozone-enhanced Combustion Derived Nickel Oxide Hole Injection Layer for Flexible Quantum Dot Light-Emitting Diodes

The Feasibility of Using Magnetron Sputtered MoOx As Effective Hole Injection Layer in Organic Light-Emitting Diode

Improved Hole Injection Property of Solution-Processed MoO<sub>3</sub> with UV-Ozone Treatment

Regulation of the Conductivity and Work Function of PEDOT:PSS Using MoO2 Nanocrystals to Achieve Efficient CsPbBrxI3-x Red Light Quantum Dot Light-Emitting Diodes

Low-temperature MoO3 film from a facile synthetic route for an efficient anode interfacial layer in organic optoelectronic devices

An Efficient Solution-Processed Hole Injection Layer with Phosphomolybdic Acid in Quantum Dot Light-Emitting Diodes

Room-temperature sol-gel derived molybdenum oxide thin films for efficient and stable solution-processed organic light-emitting diodes.

Improved Hole Injection Property of Solution-Processed MoO 3 with

Solution-Processed MoCl5 and Its Composites for Tailoring Hole Injection in Near-Ultraviolet Organic Light-Emitting Diodes

Controllable and efficient hole-injection layers with molybdenum oxide units by solution-processed procedure for OLEDs

Low-temperature Solution-Processed Molybdenum Oxide Thin Film As ITO Modified Layer for Polymer Solar Cells

All-solution-processed High-Performance Quantum Dot Light Emitting Devices Employing an Inorganic Thiocyanate As Hole Injection Layer

Flexible Substrate–Compatible and Efficiency–Improved Quantum–Dot Light–Emitting Diodes with Reduced Annealing Temperature of NiOx Hole–Injecting Layer