Abstract:The hole injection layer (HIL) plays a significant role in determining the performances of organic light-emitting diodes (OLEDs), especially when hole transport materials with deep highest occupied molecular orbital levels (HOMOs) are employed. Intensive efforts have been devoted to exploring novel hole injection materials with good solution-processing abilities in recent years. In this study, the solution-processed molybdenum trioxide (s-MoO3) is prepared via an ultra-facile method. Three different s-MoO3 layers prepared by three different methods, viz. layers annealed at 150 degrees C (s-MoO3 (150)), layers annealed at 150 degrees C and then processed in UV-ozone for 15 min (s-MoO3 (150, UVO)), and layers processed in UV-ozone for 15 min without annealing (s-MoO3 (UVO)), are obtained to investigate their influences on hole injection. The device with the s-MoO3 (150) layer has the lowest current density and the largest driving voltage, showing poor hole injection ability. In contrast, with the s-MoO3 (150, UVO) layer as HIL, the OLED produces a greatly enhanced current and sharply reduced driving voltage, comparable to the device using vacuum-evaporated MoO3. Similar results are obtained for the device with the s-MoO3 (UVO) film, suggesting that high-temperature annealing is not essential for the s-MoO3 film with UV-ozone treatment. Hole injection efficiencies of MoO3 films are quantitatively characterized by analyzing the space-charge-limited current of hole-only devices; the hole injection efficiencies of s-MoO3 (150, UVO) and s-MoO3 (UVO)-based devices are similar to 0.1, far exceeding that of the s-MoO3 (150)-based device (10(-5)). XPS analysis is performed to detect the impact of the above treatments on the surface electronic properties of the s-MoO3 films. A typical characteristic of Mo5+ species is obtained for the s-MoO3 (150) film and a high-binding-energy shoulder appears in the O 1s peak of the s-MoO3 (150) film, indicating the existence of oxygen vacancies and oxygen adsorbed at the surface of s-MoO3 (150) film. When UV-ozone treatment is applied to this s-MoO3 (150) film, it produces a decrease of Mo5+ state and elimination of oxygen-rich adsorbates, resulting in MoO3 stoichiometry similar to that of the vacuum-evaporated MoO3 film. Consequently, a maximum current efficiency of 48.3 cd.A(-1) is realized with the optimized UV-ozone treated s-MoO3 HIL. It This UV-ozone treated s-MoO3 should have widespread applications in low-cost solution-processed OLEDs as an excellent hole injection layer.

Solution-processed MoOx Hole Injection Layer Towards Efficient Organic Light-Emitting Diode

Facile Solution-Processed Aqueous MoOx for Feasible Application in Organic Light-Emitting Diode

Solution Process Feasible Highly Efficient Organic Light Emitting Diode with Hybrid Metal Oxide Based Hole Injection/Transport Layer

Solution-Processed Aqueous Composite Hole Injection Layer of Pedot:Pss+Moox for Efficient Ultraviolet Organic Light-Emitting Diode

The Feasibility of Using Magnetron Sputtered MoOx As Effective Hole Injection Layer in Organic Light-Emitting Diode

Solution-Processed Composite Interfacial Layer of MoOx-Doped Graphene Oxide for Robust Hole Injection in Organic Light-Emitting Diode

Aqueous Solution‐Processed Vanadium Oxide for Efficient Hole Injection Interfacial Layer in Organic Light‐Emitting Diode

Solution-processed Phosphorus-Tungsten Oxide Film As Hole Injection Layer for Application in Efficient Organic Light-Emitting Diode

Sol-gel Processed Vanadium Oxide As Efficient Hole Injection Layer in Visible and Ultraviolet Organic Light-Emitting Diodes

Enhancing Hole Injection by Processing ITO Through MoO3 and Self-Assembled Monolayer Hybrid Modification for Solution-Processed Hole Transport Layer-Free OLEDs

Controllable and efficient hole-injection layers with molybdenum oxide units by solution-processed procedure for OLEDs

Room-temperature sol-gel derived molybdenum oxide thin films for efficient and stable solution-processed organic light-emitting diodes.

Improved Hole Injection Property of Solution-Processed MoO<sub>3</sub> with UV-Ozone Treatment

Solution-processed WOx Hole Injection Layer for Efficient Fluorescent Blue Organic Light-Emitting Diode

The Feasibility of Using Solution-Processed Aqueous La2O3 As Effective Hole Injection Layer in Organic Light-Emitting Diode

Enhanced Performance in Organic Light-Emitting Diode by Utilizing MoO3-doped C60 As Effective Hole Injection Layer

Efficient Organic-Inorganic Hybrid Hole Injection Layer for Organic Light-Emitting Diodes by Aqueous Solution Doping

Enhanced Hole Injection and Improved Performance in Organic Light-Emitting Devices by Utilizing a Novel Composite Hole Injection Layer

Improved Hole Injection Property of Solution-Processed MoO 3 with

Realizing both improved luminance and stability in organic light-emitting devices based on a solution-processed inter-layer composed of MoO X and Au nanoparticles mixture

Efficiency Enhancement of Organic Light-Emitting Diodes Via a Self-Assembled Moth-Eye Nanopatterned Hole-Transporting Layer.