Abstract:To enhance the efficiency of cathode electron injection of organic light-emitting diode (OLEDs), we designed a new hybrid modified layer (HML) with the structure of Bphen: LiF/Al/MoO3, which was applied to ITO/NPB/Alq(3)/Al. The traditional material LiF is used for the electron injection layer of the reference device. The results show that using HBL at the interface between organic and cathode is very effective. We have measured the electroluminescence (EL) spectra of the device. The EL peak of the device is 534 nm, which indicates that it is from Alga. It can be seen that the structure design of the multilayer modified layer does not change the luminescence spectrum of the device. Bright green emission can be obtained from the optimized EL devices. Compared with traditional device based on LiF, the performance of the single unit with hybrid modification layer has better luminous properties and efficiency. Present research work shows that when the optimum parameter of the hybrid layer is Bphen LiF(5 nm; 6%)/Al(1nm)/MoO3(5 nm), the maximum current efficiency and the maximum power efficiency of the device are 4. 28 cd.A(-1) and 2. 19 lm.W-1, respectively, which are 25. 5% and 23. 7% higher than those of the reference device. Current-voltage characteristics demonstrate that the hybrid interfacial layer can promote electron injection, thus increasing the current efficiency and reduced their operating voltage slightly of OLED. We systematically analyze the improvement of device performance from two aspects. On the one hand, LiF can fill the electron trap of Bphen to enhance the current injection, moreover, HML can also block hole transport and reduce the hole current. On the other hand, based on charge balance factor theory, HML enhances the injection of electrons and increases the charge balance factor, which improves the balance of carriers in the device. The experimental results show that the cathode hybrid layer can improve the performance of the device.

Realizing both improved luminance and stability in organic light-emitting devices based on a solution-processed inter-layer composed of MoO X and Au nanoparticles mixture

Mixing plasmonic Au nanoparticles into all polymer layers for improving the efficiency of organic solar cells

Solution-processed MoOx Hole Injection Layer Towards Efficient Organic Light-Emitting Diode

The role of molybdenum oxide as anode interfacial modification in the improvement of efficiency and stability in organic light-emitting diodes

The Origin Of The Improved Efficiency And Stability Of Triphenylamine-Substituted Anthracene Derivatives For Oleds: A Theoretical Investigation

Electroluminescence Performance Of Organic Light-Emitting Diode With Molybdenum Trioxide Inside Hole Transport Layer

Efficiency Enhancement of Organic Light-Emitting Diodes Via a Self-Assembled Moth-Eye Nanopatterned Hole-Transporting Layer.

Bottom Contact Metal Oxide Interface Modification Improving the Efficiency of Organic Light Emitting Diodes

Improved Performances of Organic Light-Emitting Diodes with Mixed Layer and Metal Oxide As Anode Buffer

Hybrid Organic Light-Emitting Device Based on Ultrasonic Spray-Coating Molybdenum Trioxide Transport Layer with Low Turn-on Voltage, Improved Efficiency & Stability

Enhanced Efficiency of Organic Light-Emitting Devices by Using a Directly Imprinted Nanopillared Ultrathin Metallic Electrode.

Mixed Organic Thin Films for Organic Light-emitting Diodes

Disordered Nano‐Hemisphere Molybdenum Trioxide for Enhanced Light Out‐Coupling in Organic Light‐Emitting Diodes

Solution Process Feasible Highly Efficient Organic Light Emitting Diode with Hybrid Metal Oxide Based Hole Injection/Transport Layer

Tandem Organic Light-Emitting Diode with a Molybdenum Tri-Oxide Thin Film Interconnector Layer

Electro-optical performance of molybdenum oxide modified aluminum doped zinc oxide anodes in organic light emitting diodes: A comparison to indium tin oxide

Improved Performance of Si-based Top-Emitting Organic Light-Emitting Device Using MoOx Buffer Layer

Improved Performance with a Hybrid Cathodic Interfacial Layer in OLEDs

Enhanced Hole Injection and Improved Performance in Organic Light-Emitting Devices by Utilizing a Novel Composite Hole Injection Layer

Phosphorescent PtAu2 Complexes with Differently Positioned Carbazole-Acetylide Ligands for Solution-Processed Organic Light-Emitting Diodes with External Quantum Efficiencies of over 20.

Improved performances of the organic light-emitting devices by doping in the mixed layer