Abstract:Two series of uniaxial tensile tests are performed on isotactic polypropylene with the strain rates ranging from 5 to 200mm/min. In the first series, injection-molded specimens are used without thermal pre-treatment. In the other series of experiments, the samples are annealed for 51h at 160°C prior to testing.A constitutive model is developed for the viscoplastic behavior of isotactic polypropylene at finite strains. A semicrystalline polymer is treated as equivalent heterogeneous network of chains bridged by permanent junctions (physical cross-links and entanglements). The network is thought of as an ensemble of meso-regions connected with each other by links (lamellar blocks). In the sub-yield region of deformations, junctions between chains in meso-domains slide with respect to their reference positions (which reflects sliding of nodes in the amorphous phase and fine slip of lamellar blocks). Above the yield point, the sliding process is accompanied by displacements of meso-domains in the ensemble with respect to each other (which reflects coarse slip and fragmentation of lamellar blocks). To account for alignment of disintegrated lamellar blocks along the direction of maximal stresses (which is observed as strain-hardening of specimens in the post-yield regions of deformations) elastic moduli are assumed to depend on the principal invariants of the right Cauchy–Green tensor for the viscoplastic flow.Stress–strain relations for a semicrystalline polymer are derived by using the laws of thermodynamics. The constitutive equations are determined by five adjustable parameters that are found by matching observations. Fair agreement is demonstrated between the experimental data and the results of numerical simulation. A noticeable difference is revealed between the mechanical responses of non-annealed and annealed specimens: (i) necking of samples not subjected to thermal treatment precedes coarse slip and fragmentation of lamellar blocks, whereas cold-drawing of annealed specimens up to a longitudinal strain of 80% does not induce spatial heterogeneity of their deformation; (ii) the elastic modulus increases with the strain rate for non-annealed specimens and decreases for annealed samples.

On the effective elastic properties of isotactic polypropylene

The effect of strain rate on the viscoplastic behavior of isotactic polypropylene at finite strains

The effect of annealing on the elastoplastic and viscoelastic responses of isotactic polypropylene

Molecular Orientations and True Stress−Strain Relationship in Isotactic Polypropylene Film

The effect of annealing on the elastoplastic response of isotactic polypropylene

Application of an interpenetrating network model to the solid deformation of a quenched isotactic polypropylene film

The nonlinear time-dependent response of isotactic polypropylene

STUDY ON CRYSTALLIZATION BEHAVIOR OF ISOTACTIC POLYPROPYLENE PRODUCED BY SUPERCRITICAL POLYMERIZATION

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. 2. Molecular Orientation During Necking Process of Isotactic Polypropylene

Processing-structure-mechanical property relationships of semicrystalline polyolefin-based block copolymers

Preparation of High Modulus and High Strength Fiber by Zone-annealing Method

Retrospecting the relationship between interlamellar amorphous structure and intrinsic modulus of semicrystalline polymers via in-situ positron annihilation lifetime spectroscopy and in-situ X-ray scattering

Application of an Interpenetrating Network Model to the Necking in the Microcrystalline Region in Four Annealed Isotactic Polypropylene Films Subjected to Uniaxial Stretching at Room Temperature

Elastic properties of cellular polypropylene films: Finite element simulations and their comparison with experiments

Processing‐structure‐mechanical property relationships of semicrystalline polyolefin‐based block copolymers

Effect of isotacticity distribution on the crystallization and melting behavior of polypropylene

Crystallization and multiple melting behavior of oriented thick lamellae in isotactic polypropylene

Effect of Isotacticity Distribution on Crystallization Kinetics of Polypropylene

Interplay between crystallization behaviors and extensional deformation of isotactic polypropylene and its blend with poly(ethylene-co-octene)

Effect of Phase Structure on the Viscoelasticity and Mechanical Properties of Isotactic Polypropylene Multicomponent Polymerized with Non-Conjugated α,ω-Diene

Identification of the true elastic modulus of high density polyethylene from tensile tests using an appropriate reduced model of the elastoviscoplastic behavior