Abstract:Two series of uniaxial tensile tests are performed on isotactic polypropylene with the strain rates ranging from 5 to 200mm/min. In the first series, injection-molded specimens are used without thermal pre-treatment. In the other series of experiments, the samples are annealed for 51h at 160°C prior to testing.A constitutive model is developed for the viscoplastic behavior of isotactic polypropylene at finite strains. A semicrystalline polymer is treated as equivalent heterogeneous network of chains bridged by permanent junctions (physical cross-links and entanglements). The network is thought of as an ensemble of meso-regions connected with each other by links (lamellar blocks). In the sub-yield region of deformations, junctions between chains in meso-domains slide with respect to their reference positions (which reflects sliding of nodes in the amorphous phase and fine slip of lamellar blocks). Above the yield point, the sliding process is accompanied by displacements of meso-domains in the ensemble with respect to each other (which reflects coarse slip and fragmentation of lamellar blocks). To account for alignment of disintegrated lamellar blocks along the direction of maximal stresses (which is observed as strain-hardening of specimens in the post-yield regions of deformations) elastic moduli are assumed to depend on the principal invariants of the right Cauchy–Green tensor for the viscoplastic flow.Stress–strain relations for a semicrystalline polymer are derived by using the laws of thermodynamics. The constitutive equations are determined by five adjustable parameters that are found by matching observations. Fair agreement is demonstrated between the experimental data and the results of numerical simulation. A noticeable difference is revealed between the mechanical responses of non-annealed and annealed specimens: (i) necking of samples not subjected to thermal treatment precedes coarse slip and fragmentation of lamellar blocks, whereas cold-drawing of annealed specimens up to a longitudinal strain of 80% does not induce spatial heterogeneity of their deformation; (ii) the elastic modulus increases with the strain rate for non-annealed specimens and decreases for annealed samples.

The nonlinear time-dependent response of isotactic polypropylene

A Constitutive Model for Strain Hardening Behavior of Predeformed Amorphous Polymers: Incorporating Dissipative Dynamics of Molecular Orientation

The effect of strain rate on the viscoplastic behavior of isotactic polypropylene at finite strains

Creep-induced Anisotropy in Covalent Adaptable Network Polymers.

Modeling the Effect of Physical Aging on the Stress Response of Amorphous Polymers Based on a Two-Temperature Continuum Theory

The effect of annealing on the elastoplastic and viscoelastic responses of isotactic polypropylene

Application of an interpenetrating network model to the solid deformation of a quenched isotactic polypropylene film

Application of an Interpenetrating Network Model to the Necking in the Microcrystalline Region in Four Annealed Isotactic Polypropylene Films Subjected to Uniaxial Stretching at Room Temperature

Modeling the Rate-Dependent Ductile-Brittle Transition in Amorphous Polymers

Molecular Orientations and True Stress−Strain Relationship in Isotactic Polypropylene Film

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. 2. Molecular Orientation During Necking Process of Isotactic Polypropylene

Constitutive Modeling of Nonlinear Strain and Time Dependent Behaviors of Ballistic Gelatin at Low Strain Rates

Structure/property relationship of semi-crystalline polymer during tensile deformation: A molecular dynamics approach

A modified neo-Hookean model for semi-crystalline thermoplastics assessed by relaxation and zero-stress creep tests of recycled polypropylene and polyoxymethylene

Time-Dependent Constitutive Behaviors of a Dynamically Crosslinked Glycerogel Governed by Bond Kinetics and Chain Diffusion

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. Part Iii: Influence of Morphology on Molecular Orientation of Isotactic Polypropylene Films Subjected to Uniaxial Stretching

A Rate‐type Nonlinear Viscoelastic–viscoplastic Cyclic Constitutive Model for Polymers: Theory and Application

A viscoelastoplastic constitutive model of semi-crystalline polymers under dynamic compressive loading: Application to PE and PA66

Tensile Creep Failure of Isotactic Polypropylene under the Strain Criterion

Microstructural Evolution of Isotactic‐Polypropylene During Creep: an in Situ Study by Synchrotron Small‐Angle X‐Ray Scattering

Understanding Creep Behavior of Semicrystalline Polymer Via Coarse‐Grained Modeling