Abstract:Thermoplastic polyurethane elastomer (TPU) foams were prepared using the high-pressure autoclave with supercritical fluid carbon dioxide (SC-CO 2 ). The effects of foaming variables (i.e. saturation temperature, saturation pressure, and depressurization rate) on cellular structure and expansion ratio were investigated. The model between expansion ratio and foaming variables was constructed using the Box-Behnken design (BBD) of response surface methodology (RSM), and analysis of variance (ANOVA) was conducted to evaluate the validity and significance of the model. Finally, the interactive effects of foaming variables on the expansion ratio were investigated, and the expansion ratios of maximum and center point from numerical model were verified by experiment. The result showed higher saturation pressure and depressurization rate resulted in the more uniform cellular structure and higher cell density, however the higher saturation temperature resulted in the bigger cell and nonuniform structure. The ranges of average cell diameter and cell density were 15.26–45.4 μm and 0.32 × 10 8 to 6.24 × 10 8 cells/cm 3 , respectively. The model obtained using BBD of RSM was valid to predict the expansion ratio in the design window. The saturation temperature was the most important factor influencing the expansion ratio. With the increase of saturation temperature, the expansion ratio always increases in the design window. The maximum expansion ratio from numerical optimization was 4.91, which was located at saturation temperature 190°C, saturation pressure 12.51 MPa, and depressurization rate 5 MPa/s, and the corresponding experiment value was 4.56. The error between them was 7.13%.

Foaming Window for Preparation of Microcellular Rigid Polyurethanes Using Supercritical Carbon Dioxide As Blowing Agent

Strategy for Preparation of Microcellular Rigid Polyurethane Foams with Uniform Fine Cells and High Expansion Ratio Using Supercritical CO2 As Blowing Agent

Microcellular Foaming of Polysulfones in Supercritical CO2 and the Effect of Co-Blowing Agent

Study on the Foaming Behaviors of PBS and its Modification with PA6IcoT Assisted by scCO2

Experimental and Numerical Study of the Polyurethane Foaming Process Using High-Pressure CO2

Microcellular Thermoplastic Polyurethanes and Their Flexible Properties Prepared by Mold Foaming Process with Supercritical CO2

Mechanical Properties of Polyurethane Foams Prepared from Liquefied Corn Stover with PAPI.

Foaming of Polypropylene with Supercritical Carbon Dioxide

Study on Liquid CO2 Assisting Water Blown Spray PU Rigid Foam

Preparation of Low Density Microcellular Thermoplastic Polyurethane with High Compression Properties Based on Micro-Phase Separation Structure

Study on Extrusion Foaming of Polypropylene/Polydimethylsiloxane Blends

Physical Properties of Microcellular Polymeric Foams with Supercritical CO2

Optimization of Reaction Conditions for Polyurethane Foam Synthesis with Liquefied Corn Stalk by Response Surface Methodology

Polysulfone foam with high expansion ratio prepared by supercritical carbon dioxide assisted molding foaming method

Solubility and Diffusion Behavior of Compressed CO2 in Polyurethane Oligomer

Preparation and Density Control of Pmma Microcellular Foams Via Supercritical Carbon Dioxide Foaming

Preparation and Mechanical Properties of Polyphenylene Sulfone Foams

Batch foaming of ultra-high molecular weight polyethylene with supercritical carbon dioxide: Influence of temperature and pressure

Solid‐state Microcellular High Temperature Vulcanized (HTV) Silicone Rubber Foam with Carbon Dioxide

Investigation into the effects of foaming variables on the cellular structure and expansion ratio of foamed TPU using response surface methodology

Controlled Foaming of Polycarbonate/polymethyl Methacrylate Thin Film with Supercritical Carbon Dioxide