Abstract:This work is aimed at studying the foaming behavior of pure ultra-high molecular weight polyethylene (UHMWPE) with supercritical carbon dioxide (scCO2). The effects of foaming temperature and saturation pressure on the final foam structure were investigated by using two different one-step batch foaming processes. An in-situ high-pressure observing system was used to record the crystal change of UHMWPE film during heating and cooling stages with/without pressurized CO2. The results showed that the cell size and the cell density were affected by the combined effects of crystal, temperature, and pressure. Experimental results with different foaming temperatures showed that higher foaming temperatures led to larger cells and lower cell densities. In the processes of foaming during the heating stage (Proc1) and cooling stage (Proc2), the expansion ratio increased first and then decreased with the increase of temperature. Before obtaining the maximum expansion ratio, compare with Proc2, the cell size and expansion ratio of foams were smaller, and the cell density was higher in Proc1. Experimental results with different saturation pressures showed that higher pressure led to lower cell density and larger average cell diameter in Proc1 due to the reduction of crystals and melt strength. While in Proc2, higher saturation pressure led to higher cell density due to the increase of solubility of CO2, and the cell density decreased as the pressure further increased due to cell coalescence.

Microcellular Foaming of Polysulfones in Supercritical CO2 and the Effect of Co-Blowing Agent

Study on Microcellular Foaming of Poly(phenylene sulifde)/Poly(ether ether ketone) Blends Using Supercritical Carbon Dioxide

Study on the Foaming Behaviors of PBS and its Modification with PA6IcoT Assisted by scCO2

Microcellular foaming of poly(phenylene sulfide)/poly(ether sulfones) blends using supercritical carbon dioxide

Foaming Window for Preparation of Microcellular Rigid Polyurethanes Using Supercritical Carbon Dioxide As Blowing Agent

Effects of Processing Parameters and Thermal History on Microcellular Foaming Behaviors of PEEK Using Supercritical CO2

Microcellular Foaming Of Polypropylene/Polystyrene Blends Using Supercritical Fluid

Foaming of Polypropylene with Supercritical Carbon Dioxide

Microcellular Foams of Glass-Fiber Reinforced Poly(phenylene Sulfide) Composites Generated Using Supercritical Carbon Dioxide

Tailored Morphologies and Properties of High-Performance Microcellular Poly(phenylene Sulfide)/poly(ether Ether Ketone) (PPS/PEEK) Blends

Systematic Study of Alcohols Based Co-Blowing Agents for Polystyrene Foaming in Supercritical CO2: Toward the High Efficiency of Foaming Process and Foam Structure Optimization

Dual Role of PDMS on Improving Supercritical CO2 Foaming of Polypropylene: CO2-philic Additive and Crystallization Nucleating Agent

Preparation of Microcellular Polypropylene/Poly(octene-ethylene) Foams by Using Supercritical Carbon Dioxide

Physical Properties of Microcellular Polymeric Foams with Supercritical CO2

Polysulfone foam with high expansion ratio prepared by supercritical carbon dioxide assisted molding foaming method

Fabrication of Microcellular Polycarbonate Foams with Unimodal or Bimodal Cell-Size Distributions Using Supercritical Carbon Dioxide As A Blowing Agent

Strategy for Preparation of Microcellular Rigid Polyurethane Foams with Uniform Fine Cells and High Expansion Ratio Using Supercritical CO2 As Blowing Agent

Study on Extrusion Foaming of Polypropylene/Polydimethylsiloxane Blends

Microcellular Foaming of Polypropylene/Clay Nanocomposites with Supercritical Carbon Dioxide

Supercritical CO2 in Controlling Phase Morphology of Polypropylene/polystyrene Blends and the Corresponding Mechanical Properties and Foamability

Batch foaming of ultra-high molecular weight polyethylene with supercritical carbon dioxide: Influence of temperature and pressure