Abstract:Low-melting-point silicon-boron system alloys are promising for low-temperature reactive melt infiltration to reduce high-temperature damage to silicon carbide fibers during the densification of SiC/SiC composites. Meanwhile, the oxidation resistance of the alloys will have a large impact on the intrinsic oxidation resistance of the composite. Herein, three alloys, Si-14.88B-7Mo, Si-14.88B-7Ti, and Si-14.88B-7Cr, were fabricated to investigate the oxidation behavior in air at 1000-1400 °C. The results showed that the oxidation weight gains of the Si-B-Mo alloy after oxidation at 1400 °C for 100 h were 0.9 mg/cm, which were only 50 and 1.5% of those of Si-B-Ti and Si-B-Cr alloys, respectively. The excellent oxidation resistance of Si-B-Mo alloys at 1000-1400 °C was attributed to the formation of glassy-surface layers and the dense internal oxide layer. The dense oxide layer and the low solubility of Mo ions in SiO inhibit the volatilization of MoO and the oxidation reaction, reducing the oxidation rate of the Si-B-Mo alloy. The difference in the coefficients of thermal expansion for SiO and TiO led to penetrating cracks in the oxide layer of the Si-B-Ti alloy during cooling, thereby reducing the oxidation resistance. In addition, the rate of volatilization of CrO as CrO in an oxidation atmosphere above 1200 °C increased significantly in the Si-B-Cr alloy. The simultaneous volatilization of BO and CrO resulted in the formation of loose oxide layers in the CrB region of the Si-B-Cr alloy, leading to severe oxidation.

Isothermal and Cyclic Oxidation Behaviours of MoSi2 with Additions of B at 1250 °C Prepared by Spark Plasma Sintering

Formation and Oxidation Behavior of Mo-Si-B Composite Coatings with B-rich Interlayer Prepared by Slurry Sintering Method

Preparation and enhanced oxidation behavior of microalloyed Mo5SiB2 alloy at 1300 °C

Effects of boron addition on the high temperature oxidation of MoSi2 alloys

Oxidation Behavior of Multiphase Mo5SiB2 (T2)-Based Alloys at High Temperatures

Oxidation behavior of Mo–12.5Si–25B alloy at high temperature

Microstructure and Oxidation Behavior of Directionally Solidified Mo–Mo5SiB2 (t2)–mo3si Alloys

High-temperature Oxidation of Mo-rich (mo1−xnbx)si2 Pseudo-Binary Compounds

Effect of minor B modification on the oxidation behavior of MoSi 2 alloy at high temperature

Oxidation Behavior of the Si-B-X (X = Mo, Cr, or Ti) Alloys in the Temperature Range of 1000–1400 °C

Microstructure and Oxidation Behavior of Mo-Si-B Ternary Silicide

Microstructure and oxidation behaviour of MoSi2 coating combined MoB diffusion barrier layer on Mo substrate at 1300 °C

Microstructure and oxidation response of Mo-Si-B-ZrB 2 alloy at 900 °C: Effect of pre-oxidation treatment

Oxidation Response Determined by Multiphase-Dependent Melting Degree of Plasma Sprayed MoSi2 on Nb-based Alloy

Study on the Pre-Oxidation and Resulting Oxidation Mechanism and Kinetics of Mo-9Si-8B Alloy

High-Temperature Creep and Oxidation Behavior of Mo-Si-B Alloys with High Ti Contents

Synthesis and properties of MoAlB composites reinforced with SiC particles

Effect of Si solution in α-Mo on oxidation behavior of Mo-Si-B alloy and oxidation kinetics model

Preparation and high‐temperature oxidation resistance of multilayer MoSi 2 /MoB coating by spent MoSi 2 ‐based materials

Influence of TiC contents on the microstructure, mechanical properties, and oxidation behavior of Mo–10Si–8B alloys

Preparation of MoSi<SUB>2</SUB>-X(X=B, Al, Nb) Alloys by Mechanical Alloying and Pulse Discharge Sintering Process