Abstract:The 2195 Al-Cu-Li alloy is widely utilized in the aerospace industry due to its lightweight nature and high strength. Consequently, gaining a comprehensive understanding of techniques to enhance its microstructural and mechanical properties is crucial for the consistent production of reliable and high-strength aerospace components. In this investigation, a pristine 2195 industrial ingot was subject to three distinct forging pretreatments: PT1, which involved a direct three upsetting and three stretching (3U3S) process; PT2, which combined double stage homogenization (DH) with 3U3S; and PT3, which involved DH along with six upsetting and six stretching (6U6S). Subsequent warm deformation and T8 aging treatment were applied to the pretreated forgings. The microstructure evolution during the processes and the final mechanical properties in three orthogonal dimensions were examined. The findings revealed that the combination of DH and multi-dimensional forging (MDF) facilitated the dissolution of non-equilibrium phases to a greater extent. Consequently, the main strengthening phase transformed from the T 1 + δ` phase observed in PT1 to the denser T1 + little θ` phase observed in PT2 and PT3 after T8 aging treatment. Notably, the tensile strength and yield strength of PT2 and PT3 specimens increased by 20-30 MPa in all three directions. Moreover, the MDF process accelerated the recrystallization behavior from PT1 to PT3, resulting in a gradual reduction in the average grain size of the pretreated samples from 356 μm to 186 μm. Following warm forging and T8 aging, the grains exhibited a finer and equiaxed structure. Additionally, the coarse phase was identified as the primary source of transgranular cracking. The coarse phases within the matrix became more homogeneous and finer from PT1 to PT3, with a gradual decrease in their area fraction. On the fracture surfaces, the aggregation of coarse phases diminished. Consequently, the elongation in the z-direction improved, and the elongation anisotropy and standard deviation decreased in all three directions for PT3 specimens. The findings presented in this study provide valuable insights into the high-performance manufacturing of Al-Cu-Li alloys.

Relationships among reinforcement volume fraction, microstructure and tensile properties of (TiBw + TiCp)/Ti composites after (α + β) forging

High Temperature Tensile Properties of in Situ TiBw/Ti6Al4V Composites with a Novel Network Reinforcement Architecture

Tailoring A Novel Network Reinforcement Architecture Exploiting Superior Tensile Properties of in Situ Tibw/Ti Composites

Room temperature tensile fracture characteristics of in situ TiBw/Ti6Al4V composites with a quasi-continuous network architecture

Effects of multi-directional forging on the microstructure and mechanical properties of TiB2 particulate reinforced 6061Al composite

Thermomechanical Processing of a Near-α Ti Matrix Composite Reinforced by TiBw

Microstructures and mechanical properties of (TiBw+Ti 5 Si 3 )/TC11 composites fabricated by hot isostatic pressing and subjected to 2D forging

Anisotropic microstructure and mechanical properties of as-forged (Ti, Nb)B/Ti2AlNb composites

Microstructure and mechanical properties of in situ TiB 2 •TiAl 3 /2024Al composite subjected to multidirectional forging

In situ (TiBw+TiCp)/Ti6Al4V composites with a network reinforcement distribution

Microstructure and mechanical properties of in-situ hybrid reinforced (TiB+TiC)/Ti composites prepared by laser powder bed fusion

Configuration of new fiber-like structure driven high matching of strength-ductility in TiB reinforced titanium matrix composites

Microstructural characterization and mechanical properties of (TiC+TiB)/TA15 composites prepared by an in-situ synthesis method

Strength improvement and fracture mechanism in Fe40Al/TiC composites with high content of TiC

Forging–microstructure–tensile properties correlation in a new near β high-strength titanium alloy

Microstructure of ZrB2/6063Al In Situ Composite Processed by Forge

Simultaneous Improvement in Strength and Ductility of TC4 Matrix Composites Reinforced with Ti1400 Alloy and In Situ-Synthesized TiC

Hydrogen-induced microstructure optimization and mechanical properties enhancement of forged (TiB + TiC)/Ti6Al4V

Microstructure characteristics and enhanced properties of network-structured TiB/(TA15-Si) composites via rolling deformation at different temperatures

Enhancing strength-ductility synergy in nano-sized TiB 2 /Al composite via rapid solidification and thermo-mechanical processing

Effect of forging pretreatment on the microstructures and mechanical properties of the Al-Cu-Li alloy