Abstract:In this article, using controllable magnetron sputtering of indium tin oxide (ITO) materials on single crystal silicon at 100 °C, the optoelectronic heterojunction frame of ITO/a-SiOx(In)/n-Si is simply fabricated for the purpose of realizing passivation contact and hole tunneling. It is found that the gradation profile of indium (In) element together with silicon oxide (SiOx/In) within the ultrathin boundary zone between ITO and n-Si occurs and is characterized by X-ray photoelectron spectroscopy with the ion milling technique. The atomistic morphology and physical phase of the interfacial layer has been observed with a high-resolution transmission electron microscope. X-ray diffraction, Hall effect measurement, and optical transmittance with Tauc plot have been applied to the microstructure and property analyses of ITO thin films, respectively. The polycrystalline and amorphous phases have been verified for ITO films and SiOx(In) hybrid layer, respectively. For the quantum transport, both direct and defect-assisted tunneling of photogenerated holes through the a-SiOx(In) layer is confirmed. Besides, there is a gap state correlative to the indium composition and located at Ev + 4.60 eV in the ternary hybrid a-SiOx(In) layer that is predicted by density functional theory of first-principles calculation, which acts as an "extended delocalized state" for direct tunneling of the photogenerated holes. The reasonable built-in potential (Vbi = 0.66 V) and optimally controlled ternary hybrid a-SiOx(In) layer (about 1.4 nm) result in that the device exhibits excellent PV performance, with an open-circuit voltage of 0.540 V, a short-circuit current density of 30.5 mA/cm2, a high fill factor of 74.2%, and a conversion efficiency of 12.2%, under the AM 1.5 illumination. The work function difference between ITO (5.06 eV) and n-Si (4.31 eV) is determined by ultraviolet photoemission spectroscopy and ascribed to the essence of the built-in-field of the PV device. In addition, the strong inversion layer in the surface of the n-Si substrate is tentatively correlated to the a-SiOx(In) interface layer as well.

Transparent Conducting Indium-Tin-oxide (ITO) Film As Full Front Electrode in III–V Compound Solar Cell

Highly Efficient Silicon Heterojunction Solar Cells with ZnO:Al Transparent Electrode and Transition Metal Doped Indium Oxide Interfacial Layer

High-performance Thin-Film Solar Solar Cells Based on AlGaAs/GaAs Heterojunction and Localized Surface Plasmon Oscillations

GaAs Thin Film Nanostructure Arrays for III-V Solar Cell Applications

Fabrication and performance of indium oxide based transparent thin film transistors

Low-cost Sn-doped indium oxide films with high mobility by reactive plasma deposition for silicon heterojunction solar cells

Vanadium-doped indium tin oxide window layer in Sb2Se3 solar cell

Rear Interface Engineering in Solution‐Processed Submicron Cu(In,Ga)(S,Se)2 Solar Cells on Transparent Sn:In2O3 Back Contact

Transparent Electrode for Monolithic Perovskite/silicon-Heterojunction Two-Terminal Tandem Solar Cells

Effective Passivation and Tunneling Hybrid a-SiOx(In) Layer in ITO/n-Si Heterojunction Photovoltaic Device

High-efficiency ultra-thin GaAs solar cells based on ITO/Ag/ITO transparent electrodes and photonic crystals

ZnO‐doped In2O3 front transparent contact enables >24.0% silicon heterojunction solar cells

Investigation of In2O3:SnO2 films with different doping ratio and application as transparent conducting electrode in silicon heterojunction solar cell

Efficient Near‐Infrared PbS Quantum Dot Solar Cells Employing Hydrogenated In2O3 Transparent Electrode

Highly conductive and broadband transparent Zr‐doped In2O3 as the front electrode for monolithic perovskite/silicon tandem solar cells

Interface Reactive Sputtering of Transparent Electrode for High‐Performance Monolithic and Stacked Perovskite Tandem Solar Cells

Electrostatically‐sprayed Flexible Encapsulation for High‐performance III‐V Solar Cells

Cerium-Doped Indium Oxide as a Top Electrode of Semitransparent Perovskite Solar Cells

High-Mobility Hydrogenated Fluorine-Doped Indium Oxide Film for Passivating Contacts c-Si Solar Cells

12.42% Monolithic 25.42 cm 2 Flexible Organic Solar Cells Enabled by an Amorphous ITO‐Modified Metal Grid Electrode

A reduced electron-extraction barrier at an interface between a polymer poly(3-hexylthiophene) layer and an indium tin oxide layer