Study on Stress Transfer Characteristics of Multipoint Control Blank Holder

余海燕,李淑慧,陈关龙,谢汐

DOI: https://doi.org/10.3969/j.issn.1672-0121.2003.01.006

2003-01-01

Abstract:The stress transfer characteristics of multipoint blank-holder and its sensitivity to variable blank-holder force have been studied with validation of the rigidity of the blank-holder and three new kinds of blank-holder been introduced.

What problem does this paper attempt to address?

The Stress Transfer of Blank Holder and Its Effect on Sheet Formability

Shuhui Li,Yixin Zhao

2006-01-01

Abstract:The effect of blank holder thickness on stress transfer was studied by means of an elastic solid element finite element model.The simulation results were verified by experiments.The effect of the structure and thickness of the blank holder on the sheet formability was analyzed.The results show that the(elastic) solid elements model is efficient to improve the simulation accuracy of the stress transfer on blank holder and therefore improves the stamping formability prediction accuracy.The cone-shaped blank holder is beneficial to the variable blank holder force control and stamping formability improvement.
Blank Holder Force Control of Hydraulic Cushion with Soft Relief Fuzzy PID Controller

ZHANG Qiang,WEI Jian-hua,SHI Wen-zhuo

DOI: https://doi.org/10.3785/j.issn.1008-973x.2017.06.012

2017-01-01

Abstract:An open/closed loop switching-based soft relief PID (SPID) controller was presented in view that the proportional relief valve-controlled hydraulic cushion has large pressure overshoot and long adjusting time in the stamping process.The SPID controller could significantly reduce the pressure overshoot and shorten the adjusting time under the premise of ensuring steady state accuracy.Considering the inherently strong nonlinearities of the electro-hydraulic system, as well as the significant influence of different pressure instructions and stamping speeds on the pressure response of the hydraulic cushion, a soft relief fuzzy PID (SFPID) was further proposed.On the basis of SPID controller, the SFPID controller further introduced the fuzzy controller to adjust the control parameters on-line, so as to guarantee that the hydraulic cushion had good dynamic and static responses under different pressure instructions and stamping speeds.Both the simulation and experiment results validate the effectiveness of the proposed SFPID controller in the blank holder force control of hydraulic cushion.
A new device of variable blank holding force

SHI Dong-cai,WU Hua-ying,WEI Gong-ji,CHEN Feng,GUO Cheng

DOI: https://doi.org/10.3969/j.issn.1001-2168.2006.04.011

2006-01-01

Abstract:The function of blank holding force and the significance of variable blank holding force in drawing were presented.The main difficulty of variable blank holding force in application was pointed out.A set of new test device which can simulate three kinds different blank holding force curves through double taper wedge's movement was designed and manufactured.Furthermore,a set of different extreme values and variable velocity curves of the blank holding force was realized through replacing different spring and adjusting the length of regulation bolt by use of the device.As an example,rectangular box's drawing was tested in different conditions of variable blank holding force.It is shown that the gradually increasing curve is most fit for the rectangular box's drawing.The research has important significance to the engineering application of variable blank holding force technology.
Study and Countermeasure on Side Effects from Principal Stress Axis Rotation Experiment with Hollow Cylinder Apparatus

周建,沈扬,郑伟

DOI: https://doi.org/10.3969/j.issn.1000-0860.2005.11.010

2005-01-01

Abstract:Some problems from the principal stress axis rotation experiment with hollow cylinder apparatus are analyzed in detail herein;which consists of three aspects,such as the preparation of the hollow cylinder sample and the acquisition of the isotropic one;the estimation and elimination of the size effect and the end effect in the experiment;and the membrane penetration effect on both the drained and the undrained tests results,etc.The relevant countermeasures are put forward based on the systematic study concerned,and then some beneficial recommendations for obtaining and modifying the reasonable test results are presented as well.
The Effect of Variable Blank-Holder Forces on Formability of Ractangle Box Deep Drawing

孙成智,陈关龙,李淑惠,林忠钦

DOI: https://doi.org/10.3969/j.issn.1007-2012.2003.04.002

2003-01-01

Abstract:The predominant failure mode in stamping of sheet metal parts are wrinkling and fracture , in general, these defects may be eliminated by appropriate manipulated the blank holder forces. In this paper, the evaluation function of the formability of rectangle-box deep drawing was established, the effects of variable blank holder forces (spatially) on the formability of rectangular box deep drawing process was investigated based on the numerical simulation of sheet metal forming, the control strategy of the Variable blank-holder forces in rectangular box has been developed to improve the formability and to increase the attainable pan height.
Study on Calculation of Black Holder Force in Deep-Drawing Rectangle

SHI Yu-qing,LI Ling-feng

DOI: https://doi.org/10.3969/j.issn.1007-2012.2006.01.008

2006-01-01

Abstract:Blank holder force is one of the important parameters in deep drawing process of sheet metal,appropriate control of it can eliminate such defects as wrinkling and fracture.Blank-holder force of multi-point black holder are used in deep-drawing process to in crease the drawn depth and improve the quality of drawn piece.Calculation variable curve of blank holder force changing with die high for multi-point blank holding on rectangle products is introduced in this paper,the gist to realize control of variable blank holder force is providing.
Control of the blank-holder force to improve the formability of aluminum alloy sheet

Cheng-zhi SUN,Guan-long CHEN,Zhong-qin LIN,Feng Ni,Wen-hua BAO

DOI: https://doi.org/10.3969/j.issn.1005-0299.2005.04.030

IF: 1.8

2005-01-01

Materials Science and Technology

Abstract:Based on numerical simulations and experiments performed on the multi-point variable blankholder force hydraulic press, the effects of variable blankholder forces (locally around the blank holder surface) on the formability of 5052H32 aluminum alloy sheets was investigated. The simulation and experimental results demonstrated that the variable blank-holder force can improve the formability of aluminum alloy sheets and a-chieve greater draw depths (maximum draw depths improved about 12% ), and the main reason for improving the formability is that variable blankholder forces (locally around the blank holder surface) can decrease the thickness reduction and the peak value of strains in potential fracture areas. Finally, all the results derived from the FEM analysis show reasonable agreement with the experimental data.
Data-driven accurate design of variable blank holder force in sheet forming under interval uncertainty using sequential approximate multi-objective optimization.

Yixiong Feng,Zhifeng Zhang,Guangdong Tian,Zhihan Lv,Shaoxu Tian,Hongfei Jia

DOI: https://doi.org/10.1016/j.future.2017.02.048

2018-01-01

Abstract:In this paper, a sequential approximate multi-objective optimization method is employed to obtain the data-driven optimal variable blank holder forces in sheet forming under interval uncertainty. Uncertain parameters driven by data are modeled as intervals, bounds of which can be easily obtained from a small number of uncertainty information. Through a nonlinear interval number programming method, the multi-objective optimization problem under interval uncertainty is converted into a deterministic one. Considering the problem of low efficiency and local optima Caused by traditional optimization methods, sequential approximate optimization approach is introduced to improve the efficiency and the ability to find global optimal solutions during variable blank holder forces (VBHF) uncertain multi-objective optimization process. The presented method is applied to accurate design the variable blank holder force for a certain space large size thin-walled part forming under uncertainty. The forming quality is compared with deterministic multi-objective optimization of VBHF, and its effectiveness is proved. (C) 2018 Elsevier B.V. All rights reserved.
Determination of optimal blank holder force trajectories for segmented binders of step rectangle box using PID closed-loop FEM simulation

W. R. Wang,G. L. Chen,Z. Q. Lin,S. H. Li

DOI: https://doi.org/10.1007/s00170-006-0440-7

IF: 3.563

2006-01-01

The International Journal of Advanced Manufacturing Technology

Abstract:Blank holder force (BHF) is one of the key parameters affecting the process of sheet metal stamping. Numerous researchers have demonstrated two primary failures (wrinkling and tearing) could be avoided if appropriate variable BHF profile was implemented during punch stroke. Several approaches are proposed to determinate optimal BHF by experiment or FEM simulation. In this study, new control objective was adopted based on the definition and analysis of BHF formability window. The PID controller was integrated into FEM code to conduct closed-loop forming simulation of step rectangle box, through which the optimal BHF trajectories were determined for each separated binder. The trajectories were verified on a multipoint variable BHF hydraulic press and showed good effect to avoid wrinkling and tearing. The proposed BHF determination approach in this paper can be applied to stamping parts of different geometry due to the application of new objective, which makes it a robust strategy.
The Optimization Study of Variable Blank Holder Force in the Process of Deep Drawing Cylinder Parts

Wang Zhen,Zhu Wei,Li Congxin

DOI: https://doi.org/10.1109/ICMTMA.2011.794

2011-01-01

Abstract:In order to solve one Gordian knot of how to optimize the control curve of variable blank holder force (VBHF) in the process of sheet deep drawing, some plasticity analyses in theory about carry capacities of one point on the surface of flange and one point on the sidewall during the whole process of deep drawing cylinder parts were carried out firstly, and then instantaneous radial pull-stress and circumferential compress-stress formulas about one random point on the flange could be concluded out by the way of building corresponding stress-strain balance relations, the same as the corresponding max pull-stress formula about one point on the sidewall. By the aid of consulting with correlative energy conversation theorem, Hill anisotropism theory and materials strain-hardening criterion, one minimum wrinkleless VBHF expression which including friction coefficient and normal anisotropism coefficient and one critical fracture limit VBHF expression could be ratiocinated out in sequence, and some corresponding influencing disciplines of all kinds of forming parameters on these two expressions were discussed in detail. In the end, numerical simulations were adopted to validate the feasibility of two simple optimized load curves of VBHF. Final computation results showed that these two simple optimized VBHF curves could not only conduce to more uniform in thickness distribution relative to other's study results, after calculating mean square deviation of thickness variation with final parts, but also attain to lower peak with thickness variation, which dropping from 7.47% to 6.17% and from 17.65% to 15.39% respectively.
An Experimental Study for the Effect of Contact Stress of Blank Holder and Punch Velocity on Crack Ratio of Fine-Blanked Surface

Ri-xian Ding,Chen Guo,Huan-huan Zhang

DOI: https://doi.org/10.4028/www.scientific.net/amr.538-541.1115

2012-01-01

Advanced Materials Research

Abstract:In this study, the parameters (i.e., contact stress at the die-sheet interface and the punch velocity) were measured by the installation of film stress sensors in the fine-blanking die. A regression model was established to investigate the degree of importance of the parameters and their interaction on reducing the crack ratio of fine-blanked surface. Analysis of variance (ANOVA) was then performed to check the adequacy of the regression model. The optimal results of the regression model agreed well with the experimental result. The regression analysis indicated that the contact stress have a major influence, followed by the interaction and the punch velocity. The importance of the interaction means that the ability of contact stress in crack ratio reduction depends on the level of punch velocity. The result could be useful to facilitate an improvement in the quality of the fine-blanked parts by the optimization parameters.
Springback Research and Control about Mini-Car Beam Based on Variable Blankholder Force Technology

王健,胡星,刘丽娜,卢又平

DOI: https://doi.org/10.3969/j.issn.1000-3940.2008.05.015

2008-01-01

Abstract:The springback phenomenon in mini-car beam forming is one of the main quality problems,which may affect the tolerance and final shape of stampings.In order to control springback effectively,mini-car's right back beam forming was designed and simulated based on variable blank holder force technology.The result of simulation indicates that the larger span of blank holder force can induce fewer springback.Finally,a kind of variable blank holder force method which could be conveniently realized in inverted draw die was introduced.This method has been applied to the drawing of mini-car's right back beam which has good effects on springback control.Maximum springback angle diminishes from 8° to 2°.
Variable Blank Holder Force Optimization Based on PID Closed-loop Control

Shuhui Li

2007-01-01

Abstract:Blank holder force(BHF) is one of the key parameters affecting the process of sheet metal stamping.New control objective was adopted based on the definition and analysis of BHF formability window.The PID control model was established using the new objective.Closed-loop forming simulation of step rectangle box was conducted integrating the PID model,through which the optimal BHF trajectories were determined for each separated binder.The trajectories were verified on a multipoint variable BHF hydraulic press and showed good effect to avoid wrinkling and tearing under constant BHF.The proposed BHF determination approach can conduct temporal and spatial BHF optimization simultaneously,which makes it a robust strategy.
The Study of Load Curve of Critical Wrinkless Variable Blank Holder Force in the Process of Deep Drawing Cylinder Parts

ZHU Wei,DONG Xiang-huai,ZHANG Zhi-liang,SHU Shi-xiang

DOI: https://doi.org/10.3969/j.issn.1007-2012.2007.01.024

2007-01-01

Abstract:In this paper,in order to solve one Gordian knot of how to optimized control blank holder force (BHF) in the process of sheet deep drawing,some theoretic analyses about carry capacity of one point on the surface of flange during the whole process of deep drawing cylinder parts were carried out firstly,and then real-time radial pull-stress and circumferential compress-stress formulas about random point on flange could be concluded out by the way of building corresponding stress-strain balance relations.By the aid of consulting correlative energy conversation theorem and Hill anisotropism theory when wrinkling,one minimum wrinkless variable BHF expression including friction coefficient and thickness anisotropism coefficient could be ratiocinated out,and then some corresponding influencing disciplines of all kinds of forming parameters on this expression were analyzed.In the end,numerical simulations were adopted to validate the feasibility of this load curve of variable BHF and revise it.Final computation results showed that this revised minimum critical wrinkless variable BHF curve could save more outer energy and conduce to more uniform in thickness distribution after calculating mean square deviation of thickness variation with final parts.
The Effect of Binder Layouts on the Sheet Metal Formability in the Stamping with Variable Blank Holder Force

Wang Wu-rong,Chen Guan-long,Lin Zhong-qin

DOI: https://doi.org/10.1016/j.jmatprotec.2010.03.027

IF: 6.3

2010-01-01

Journal of Materials Processing Technology

Abstract:Flat-shaped and cone-shaped binders, used in the stamping with Variable Blank Holder Force (VBHF), are compared in this study by Finite Element Method (FEM) modeling and verified by experiments. Rigid shell and solid elements are used to model the binders in the VBHF forming simulation. Split has been detected with the rigid shell modeling, which is inconsistent with the experiment. Therefore, the solid element modeling is more accurate to simulate the stress transmission from the cushion cylinder to the binder, which therefore improves the accuracy of the stamping formability prediction. The comparison between the stamped parts with the two binder layouts indicates the cone-shaped binder is more beneficial to the VBHF controllability and stamping formability improvement.
Study on influencing rule of critical blank holder force of rectangular box flange wrinkling

ZANG Shun-lai,DONG Wei,QI Wen-yi,GUO Cheng

DOI: https://doi.org/10.3969/j.issn.1000-3940.2008.02.011

2008-01-01

Abstract:Wrinkling is the major defect in the rectangular box deep drawing,and blank holder force is the main method to control wrinkling.Using C-B criterion-based theoretical analysis and numerical simulation,the influences of material properties and technical parameters on the critical blank holder force of flange wrinkling were investigated.The analytic and simulation results show that material parameters,K and n,have significant influences on the critical blank holder force of flange wrinkling in the rectangular box deep drawing,but γ-value has a little influence on it.The critical blank holder force increases with the punch stroke and decreases with the round corner radius,but it is not related to the clearance between punch and die.
A New Strategy for the Optimization of Variable Blank Holder Force in Sheet Metal Forming

WANG Wu-rong,CHEN Guan-long,LIN Zhong-qin,LI Shu-hui

DOI: https://doi.org/10.3969/j.issn.1007-2012.2007.01.023

2007-01-01

Abstract:Blank holder force (BHF) is one of the key parameters controlling material flow in sheet metal forming.Numerous researches have demonstrated that an appropriate variable blank holder force (VBHF) during punch stroke is an effective technique to suppress the wrinkling for both flange and sidewall and delay the onset of tearing.In this paper,a new control objective is proposed based on the definition and analysis of BHF formability window.And then a closed-loop PID control strategy is established to determine the optimal variable BHF for each segmented binder during the punch stroke.Then a rectangular box with different corner radii using segmental binders is adopted to validate the closed-loop simulation,through which the optimal profile of variable BHF is determined for each segmental binder at different punch travel.The simulated result shows the box which is difficult to be formed under constant BHF using aluminum alloy sheet could be stamped successfully without wrinkling and tearing.Finally,the derived trajectories of optimal BHF of the rectangular box were verified on a multipoint variable BHF hydraulic press and the experiment results correspond well with those of FEM simulation.
Stamping and Stamping Simulation with a Blankholder Gap

HB Wang,WL Xu,ZQ Lin,YY Yang,ZR Wang

DOI: https://doi.org/10.1016/s0924-0136(01)01112-8

IF: 6.3

2002-01-01

Journal of Materials Processing Technology

Abstract:Applying a blankholder gap is the main method of control of the blankholder in stamping or its simulation. In this paper, the nature of stamping with a blankholder gap is provided as well as two advantages of stamping simulation with a blankholder gap. Finally, a reasonable blankholder gap for cup deep drawing and the reverse drawing process is proposed.
Numerical and Physics Simulations of Variable Blank Holder Force in Process of Deep Drawing Complex Overlay

Wei ZHU,Xiang-huai DONG,Zhi-liang ZHANG,Shi-xiang SHU

DOI: https://doi.org/10.3969/j.issn.1001-4381.2007.07.008

2007-01-01

Abstract:In order to effectively solve the problem that how to optimize the technics of variable blank holder force (BHF) in the process of deep drawing complex automotive forward-soleplates in real manufacture, one simplified simulation model was built based on the Similitude-theory. Then numerical simulations were carried out to search out which one was the best from lots of typical variable BHF modes, with better uniformity in thickness distribution and without wrinkling and cracking phenomena. Finally, physics tests were done to validate above results. Both numerical simulation and physics simulation results show that under the control of U curve of variable BHF, not only the maximum thickness-reduction of workpiece is the lowest, but also the whole mean-squared error of thickness-reduction is the minimal.
Effect of blank holder force on joining quality of the flat clinch-rivet process

Chao Chen,Xingang Zhang,Changhao Wen,Yuxin Yin

DOI: https://doi.org/10.1007/s00170-022-09744-6

IF: 3.563

2022-07-29

The International Journal of Advanced Manufacturing Technology

Abstract:Mechanical clinching is often used as a green technology to join lightweight materials. The conventional clinching process creates a joint with a high protrusion at the bottom, which affects the aesthetics of the joint. It also limits the application of the clinching process to certain functional surfaces. A modified clinching technology, flat clinch-rivet clinching, has been developed to eliminate protrusions. In the study, the effect of blank holder force on the joining quality of the modified clinched joint was investigated experimentally. Different combinations of disc springs were used to produce different blank holder forces to join double-layer AA5052 sheets. Geometry, failure modes, shear strength, and tensile strength were analyzed. The results show that increasing the blank holder force helps to prevent warping of the sheet and bulging of the joint bottom. The shear strength and tensile strength for the modified joint also increase with the growth of the blank holder force.

engineering, manufacturing,automation & control systems

Study on Stress Transfer Characteristics of Multipoint Control Blank Holder

The Stress Transfer of Blank Holder and Its Effect on Sheet Formability

Blank Holder Force Control of Hydraulic Cushion with Soft Relief Fuzzy PID Controller

A new device of variable blank holding force

Study and Countermeasure on Side Effects from Principal Stress Axis Rotation Experiment with Hollow Cylinder Apparatus

The Effect of Variable Blank-Holder Forces on Formability of Ractangle Box Deep Drawing

Study on Calculation of Black Holder Force in Deep-Drawing Rectangle

Control of the blank-holder force to improve the formability of aluminum alloy sheet

Data-driven accurate design of variable blank holder force in sheet forming under interval uncertainty using sequential approximate multi-objective optimization.

Determination of optimal blank holder force trajectories for segmented binders of step rectangle box using PID closed-loop FEM simulation

The Optimization Study of Variable Blank Holder Force in the Process of Deep Drawing Cylinder Parts

An Experimental Study for the Effect of Contact Stress of Blank Holder and Punch Velocity on Crack Ratio of Fine-Blanked Surface

Springback Research and Control about Mini-Car Beam Based on Variable Blankholder Force Technology

Variable Blank Holder Force Optimization Based on PID Closed-loop Control

The Study of Load Curve of Critical Wrinkless Variable Blank Holder Force in the Process of Deep Drawing Cylinder Parts

The Effect of Binder Layouts on the Sheet Metal Formability in the Stamping with Variable Blank Holder Force

Study on influencing rule of critical blank holder force of rectangular box flange wrinkling

A New Strategy for the Optimization of Variable Blank Holder Force in Sheet Metal Forming

Stamping and Stamping Simulation with a Blankholder Gap

Numerical and Physics Simulations of Variable Blank Holder Force in Process of Deep Drawing Complex Overlay

Effect of blank holder force on joining quality of the flat clinch-rivet process