Abstract:Ti-Al alloys as the high temperature structural material with the most prospective development are widely used in aerospace. Further study should been conducted on their formation, of fully lamellar structure in directional solidification and lamellar orientation control for a good balance of mechanical properties. Directional solidification experiments were conducted for Ti-50Al (atomic fraction, %) alloy in a relatively wide range of growth rates. The effects of growth rate on interfacial morphology, microstructure evolution and formation of lamellar structure were investigated. A single-phase growth of cellular alpha was observed in a, growth rate range of 1-5 mu m/s, and finally a fully lamellar structure was formed. When the growth rate reached 10 mu m/s, a single-phase growth of cellular alpha was also observed during a relatively long distance after initial solidification, but as solidification proceeded, intercellular solute enrichment became so severe that gamma phase precipitated from liquid appeared between alpha cells, and finally a full lamella can not be formed. When the growth rate was higher than 15 mu m/s, a dendritic growth of alpha phase and gamma phase between alpha dendrites were observed.The analysis on the final lamellar orientations at different growth rates showed that the lamellar orientation is history-dependant on the orientation of as-cast grain at the started interface of directional solidification. Based on the above rules, Ti-50Al alloy, also as seed, was solidified under controlling the lamellar orientation, and a relatively low growth rate of 8 mu m/s was chosen to ensure a single-phase growth of alpha. Finally, a fully lamellar structure with an orientation parallel to the growth direction was obtained.

Lamellar Orientation Control of Ti–47Al–0.5W–0.5Si by Directional Solidification Using Β Seeding Technique

Lamellar Orientation Control of Directionally Solidified Ti–46Al–0·5W–0·5Si Alloy by Self-Seeding Technology

The Evolution of Seeding Technique for the Lamellar Orientation Controlling of Gamma-Tial Based Alloys

Lamellar Orientation Control in Directionally Solidified Tial Intermetallics

Directional Solidification of TiAl-Based Alloys: Determination of the Primary Phase in Ti-50Al-5Nb Alloy

Lamellar Orientation and Growth Direction of Α Phase in Directionally Solidified Ti-46Al-0.5W-0.5Si Alloy

Structure Evolution of Directionally Solidified Ti-50al Alloy and Lamellar Orientation Control

A high-withdrawing-rate method to control the orientation of (?+?2) lamellar structure in a ?-solidifying ?-TiAl-based alloy

Crystallographic Origin of Phase Transformation and Lamellar Orientation Control for TiAl-Based Alloys

Microstructural Control of TiAl–Nb Alloys by Directional Solidification

The Technology of Controlled Lamellar Orientation in TiAl-based Alloys

Effect of Lamellae Orientation on Tensile Properties of Directionally Solidified Ti–46Al–0.5W–0.5Si Alloy

Controlling lamellar orientation of Ti-47.5Al-5Nb-2.5V-1Cr alloy by conventional casting

The Directional Solidification, Microstructural Characterization and Deformation Behavior of Β-Solidifying TiAl Alloy

Effects of Solidification Parameters on the Growth Direction of Α Phase in Directionally Solidified Ti-49Al Alloy

On the Orientation Relationship Between Ti5Si3 Precipitates and B2 Phase in a Ti-47Al-2W-0.5Si Alloy

Microstructure Evolution of Directionally Solidified Ti–46Al–0.5W–0.5Si Alloy

Continued Growth Controlling of the Non-Preferred Primary Phase for the Parallel Lamellar Structure in Directionally Solidified Ti–50Al–4Nb Alloy

A Novel Method to Directional Solidification of TiAlNb Alloys by Mixing Binary TiAl Ingot and Nb Wire

Formation of α-segregation and its impact on grain refinement in Ti-47.5Al-5Nb-2.5V-1Cr alloy

Microstructures, Micro-Segregation and Solidification Path of Directionally Solidified Ti-45al-5nb Alloy