Abstract:Possible lamellar coarsening in the as-cast microstructure of TiAl alloys significantly affects the subsequent processing of ingot metallurgy, and a systematic study of it is necessary. In this paper, two TiAl alloys with different solidification modes (TNM-45Al alloy and TNM-0.3Si-0.7 C alloy) were obtained by compositional minor adjustment basing on TNM alloy. The effect of different adjustment routes on the localized lamellar structure coarseing behaviour and the resulting differences in the uniformity of the nanohardness distribution were investigated by comparing with TNM alloy. It is found that increasing the Al content of the TNM alloy while keeping the solidification mode as β-solidification unchanged leads to severe localised lamellar coarsening in the S-segregation zone of TNM-45Al alloy, including continuous coarsening (CC) and discontinuous coarsening (DC). In contrast, the solidification mode of the TNM-0.3Si-0.7 C alloy with the addition of the strong α stabilizer elements Si and C is transformed into hypoperitectic solidification with severe peritectic segregation, but the lamellar structure exhibits surprising full-domain stability. The results show that the thermodynamic tendency caused by high Al content and the absence of net-like β-segregation leads to severe localised lamellar coarsening in TNM-45Al alloy. CC can be accomplished through the migration of interface defects. DC is formed by the nucleation and expansion of γ-phase Shockley incomplete dislocations, and the interfaces consist of the α 2 /γ interface and the first discovered γ /γ twin interface. The lamellar coarsening of TNM-0.3Si-0.7 C alloy can be effectively suppressed by the solid solution of Si/C atoms and the near net-like β-segregation in the primary β-phase region. As a result, the distribution uniformity of the nanohardness of the lamellar structure in TNM-0.3Si-0.7 C alloy is excellent, with the variance decreasing from ±0.24 of TNM alloy to ±0.20, while it increases to ±0.37 for the TNM-45Al alloy.

Formation of α-segregation and its impact on grain refinement in Ti-47.5Al-5Nb-2.5V-1Cr alloy

Effect of compositional minor adjustment on localized lamellar structure coarsening of TiAl alloys with different solidification modes

Formation of lamellar microstructure in Ti-48Al-7Nb-2.5V-1Cr alloy

Influence of Co Contents and Super-Gravity Field on Refinement of In-Situ Ultra-Fined Fibers in Al-2.5Ni Eutectic Alloys

Microstructure refinement of Ti-40Al-8Nb alloys via the decomposition of the metastable B2 phase at 1000 °C

Metastable microstructure evolution and grain refinement in a Low-Ta containing γ-TiAl alloy through heat treatment

Refining Ti 2 AlC in the liquid region and improving the microstructure and mechanical properties of Ti-46Al-8Nb-2.6 C alloy by adding Y

Synergistic Effect of La and TiB2 Particles on Grain Refinement in Aluminum Alloy

α′′ phase-assisted nucleation to obtain ultrafine α precipitates for designing high-strength near-β titanium alloys

Microstructure Transformation of a Refined High Nb Containing TiAl Alloy

Deformation and Phase Transformation of Disordered α Phase in the (α + γ) Two-Phase Region of a High-Nb TiAl Alloy

Segregation of alloying elements in a fully lamellar TiAl alloy

Formation of core-shell-like structure in β-solidified TiAl alloy and its effect on hot workability

Effect of cooling rate on α variant selection and microstructure evolution in a near β Ti–5Al–3Mo–3V–2Cr–2Zr–1Nb–1Fe alloy

Morphology evolution and orientation characteristics of precipitate of ultra-high strength titanium alloy

Analysis on phase transformation and lamellar formation of Ti-47.5Al-3Nb-1.5/3.5Cr alloys by confocal laser scanning in-situ observation

Segregation Behavior of Alloying Elements in Different Oriented Single Crystal Nickel Based Superalloys

Controlling lamellar orientation of Ti-47.5Al-5Nb-2.5V-1Cr alloy by conventional casting

Refinement mechanism of centimeter-grade coarse grains in as-cast Ti 2 AlNb-based alloy during multi-directional forging

Effect of ultrasonic melt processing and Al-Ti-B on the microstructural refinement of recycled Al alloys

Influence of alternate grain boundary α on the development of Widmanstätten microstructure in TC21 Ti alloy