Abstract:High sensitivity to crack and damage of chemical vapor-deposited silicon carbide (CVD- SiC) restricts the high-efficiency and low-damage manufacturing of CVD-SiC components. This paper aims to reveal the damage and material removal mechanisms of CVD-SiC after being scratched by diamond abrasives. The mechanical properties, scratching force, depth of ductile-brittle transition, residual depth and material removal damages of the CVD-SiC were discussed by the indentation, nano-scratching experiments, and compared with sintered silicon carbide (SSiC) ceramics. The results demonstrated that the mechanical properties of CVD-SiC are better than SSiC. In terms of hardness and fracture toughness, CVD-SiC demonstrates a 10– 20% and 20– 30% higher level of performance than SSiC, respectively. SSiC exhibits a brittleness level approximately 30% higher than that of CVD-SiC. SSiC ceramics are prone to crack deflection, intergranular fracture and transgranular fracture during indentation, indicating a higher propensity for brittle fracture in SSiC. The crack propagation in CVD-SiC is relatively regular. Both materials undergo the ductile, ductile-brittle transition and brittle stage, and the fluctuation variability of CVD-SiC material is notably lower than that of SSiC during the brittle stage. Compared with SSiC, the residual depth, groove width and transverse force of CVD-SiC are smaller under the same normal load. The critical depth of ductile-brittle transition of CVD-SiC is about 2 times that of SSiC in experimental and theoretical, indicating that CVD-SiC easily achieves ductile grinding. The mechanical properties, crack system and crystal structure of the CVD-SiC and SSiC materials cause the divergences in brittle removal. The radial-median crack system dominates the material removal of CVD-SiC. The disparity of deformations on the inside and outside of the crystal in the brittle stage leads to significant fluctuation variability of force and depth of SSiC during the scratching.

Role of Si in the Surface Damage Mechanism of RB-SiC/Si under Mechanical Loading

Damage characteristics and material removal mechanisms of CVD-SiC in nanotests: A comparative with sintered SiC

On the deformation mechanism of SiC under nano-scratching: An experimental investigation

Surface damage mechanism of monocrystalline silicon during single point diamond grinding

Mechanical effect of abrasives on silicon surface in chemo-mechanical grinding

Molecular dynamics analysis of subsurface brittleness mechanism of nanocrystalline 3C-SiC rough friction surface

On understanding the mechanical properties and damage behavior of C f /SiC composites by indentation method

Molecular dynamics simulation of the material removal in the scratching of 4H-SiC and 6H-SiC substrates

Material removal and damage formation mechanisms induced by periodic indentation during ultrasonic vibration-assisted scratching of SiC f /SiC composites

Anisotropic Deformation of 4H-Sic Wafers: Insights from Nanoindentation Tests

Atomistic insights on the nanoscale single grain scratching mechanism of silicon carbide ceramic based on molecular dynamics simulation

Research on the generation mechanism of surface and subsurface damage in loose abrasive lapping of RB-SiC ceramics

Coupled SPH-FEM modeling of Berkovich indenter scratching of single-crystal silicon

Response of mechanical properties and subsurface damage in β-SiC to temperature and crystal plane during nanoindentation simulation

Effect of dislocation defects on the nano-scratching process of 4H–SiC

Damage behavior and mechanism of SiCp/Al composites under biaxial tension

Solid particle erosion-wear behaviour of SiC particle-reinforced Si matrix composite and neat Si—A comparison

Cutting mechanism of reaction-bonded silicon carbide in laser-assisted ultra-precision machining

Investigation on diamond damaged process during a single-scratch of single crystal silicon carbide

Study on wear of diamond during scratching SiC using molecular dynamics simulations

Atomic Simulations of Deformation Mechanism of 3C-SiC Polishing Process with a Rolling Abrasive