Abstract:The demand for advanced Al-based alloys with tailored structural and magnetic properties has intensified for applications requiring a high thermal stability and performance under challenging conditions. This study investigated the phase evolution, magnetic properties, thermal stability, and microstructural changes in the Al-based alloys Al82Fe16Nb2 and Al82Fe14Nb2Mn2, synthesized via mechanical alloying (MA), using stearic acid as a process control agent. The X-ray diffraction results indicated that Al82Fe16Nb2 achieved a β-phase solid solution with 13–14 nm crystallite sizes after 5 h of milling, reaching an amorphous state after 10 h. In contrast, Al82Fe14Nb2Mn2 formed a partially amorphous structure within 10 h, with enhanced stability with additional milling. Magnetic measurements indicated that both alloys possessed soft magnetic behavior under shorter milling times (1–5 h) and transitioned to hard magnetic behavior as amorphization progressed. This phenomenon was associated with a decrease in saturation magnetization (Ms) and an increase in coercivity (Hc) due to structural disorder and residual stresses. Thermal stability analyses on 10 h milled samples conducted via differential scanning calorimetry showed exothermic peaks between 300 and 800 °C, corresponding to phase transformations upon heating. Post-annealing analyses at 550 °C demonstrated the presence of phases including Al, β-phase solid solutions, Al13Fe4, and residual amorphous regions. At 600 °C, the Al3Nb phase emerged as the β-phase, and the amorphous content decreased, while annealing at 700 °C fully decomposed the amorphous phases into stable crystalline forms. Microstructural analyses demonstrated a consistent reduction in and homogenization of particle sizes, with particles decreasing to 1–3 μm in diameter after 10 h. Altogether, these findings highlight MA's effectiveness in tuning the microstructure and magnetic properties of Al–Fe–Nb (Mn) alloys, making these materials suitable for applications requiring a high thermal stability and tailored magnetic responses.

Evolution of Metal Nitriding and Hydriding Reactions During Ammonia Plasma-Assisted Ball Milling

Use of Nitrogen Gas in High-Speed Milling of Ti-6Al-4V

Effect of Milling Intensity on the Formation of LiMgN from the Dehydrogenation of LiNH2–MgH2 (1:1) Mixture

The Electrochemical Evaluation of Ball Milled MgNi-based Hydrogen Storage Alloys

Effect of ball-milling on the phase structure and hydrogen storage properties of Ti0.9Zr0.1Mn1.5 alloy

Non-thermal Atmospheric Plasma Synthesis of Ammonia in a DBD Reactor Packed with Various Catalysts

Preparation of Mg2Ni Hydrogen Storage Alloy Materials by High Energy Ball Milling

Preparation of Ti/Al based nanophase composite powder by mechanical alloying

Electrochemical properties of amorphous Mg–Fe alloys mixed with Ni prepared by ball-milling

Hydrogenation of Plasma-Excited Nitrogen over an Alumina Catalyst for Ammonia Synthesis

Phase-structure and Hydrogen Storage Behaviors of Mg+10％ Ni2P Composite Prepared by Reactive Ball-Milling

Hydriding/dehydriding properties of La2Mg16Ni alloy prepared by ball milling in different milling environments

Improving hydrogen storage thermodynamics and kinetics of Ce-Mg-Ni-based alloy by mechanical milling with TiF 3

Mechanical Ball Milling Preparation and Electrochemical Hydrogen Storage Properties of Amorphous Mg-Fe Composites

Effect of Ball Milling Time on Microstructure and Hydrogen Storage Properties of Nd5Mg41Ni Alloy

Effect of Mechanical Alloying on the Microstructure of CoCrNiTiMox High Entropy Alloy

High-temperature high-pressure reactive ball milling synthesis of Mg-Ni-based solid-state hydrogen storage materials

Reaction pathways determined by mechanical milling process for dehydrogenation/hydrogenation of the LiNH2/MgH2 system

Ammonia Synthesis over Multi-Promoted Iron Catalysts Obtained by High-Energy Ball-Milling

Hydriding and dehydriding properties of nanostructured Mg2Ni alloy prepared by the process of hydriding combustion synthesis and subsequent mechanical grinding

Nanocrystalline/Amorphous Tuning of Al–Fe–Nb (Mn) Alloy Powders Produced via High-Energy Ball Milling