Abstract:CoCrFeNi and CoCrFeNiAl0.3 high entropy alloys reinforced with in-situ oxide nanoparticles have been successfully fabricated by mechanical milling in combination with hot pressing and hot extrusion. The as-fabricated CoCrFeNi samples exhibited an ultrafine grained microstructure with in-situ Cr2O3 oxide nanoparticles formed during hot pressing and extrusion process and distributed both on grain boundaries and in grain interiors. Increasing extrusion temperature from 1000 to 1100 degrees C caused a significantly increase of grain size from 700 nm to 2.5 mu m owing to recrystallization and growth of the recrystallized grains, as well as the coarsening of Cr2O3 nanoparticles with their mean size increasing from 57 to 140 nm. When adding Al elements, finer Al2O3 nanoparticles (mean size: 30 nm) formed in the CoCrFeNiAl0.3 high entropy alloy, leading to refinement of the grains (mean size: 504 nm) due to their pinning effect on grain boundary immigration. After T6 heat treatment, the CoCrFeNiAl0.3 high entropy alloy demonstrated improved mechanical properties with yield strength of 1335 MPa, ultimate tensile strength of 1346 MPa and an elongation to fracture of 7.9%. With quantitative analysis based on the current models, it was concluded that grain boundary strengthening and Orowan strengthening acted as the dominant strengthening mechanisms.

Microstructure and Properties of Ultrafine Grained AlCrFeCoNi/WC Cemented Carbides

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Microstructure and properties of coarse WC-10CoCrFeMnNi cemented carbide by mechanical alloying and hot pressing sintering

Microstructure and Mechanical Properties of WC-10wt.%AlCoCrFeNi Cemented Carbides Fabricated by Plasma-Assisted Ball Milling

Research on Microstructure and Properties of Ultrafine Grained WC-Ni3Al Cemented Carbide

Preparation and Mechanical Properties of WC-10 Ni3Al Cemented Carbides with Plate-Like Triangular Prismatic WC Grains

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides

Microstructural Characterization of Nanostructured WC-Co Cemented Carbides

Microstructure and Mechanical Properties of Ultra-Fine WC-10Co Cemented Carbides with Cr3C2 and NbC: Experimental Investigation Supported by Thermodynamic Calculation

Effect of Vc and Nbc Additions on Microstructure and Properties of Ultrafine Wc-10co Cemented Carbides

Effect of Carbon Content on the Microstructure and Properties of WC-CoCrFeNi Cemented Carbides

Fabrication and Mechanical Properties of Ultrafine Grained WC–10Co–0.45Cr3C2–0.25VC Alloys

Comparison Between Ultrafine-Grained WC–Co and WC–HEA-cemented Carbides

Effect of Cobalt Content on the Microstructure and Mechanical Properties of Coarse Grained WC-Co Cemented Carbides Fabricated from Chemically Coated Composite Powder

Investigation of ultrafine WC-Co-Fe-Ni-Cr<sub>3</sub>C<sub>2</sub> cemented carbide microstructure and properties based on phase diagram thermodynamics

The Enhancement of the Microstructure and Mechanical Performances of Ultrafine WC-Co Cemented Carbides by Optimizing Cr2(C,N) Addition and WC Particle Sizes

Fabrication and mechanical properties of WC-10Co cemented carbides with plate-like WC grains

Microstructure and Mechanical Properties of Ultrafine Grained CoCrFeNi and CoCrFeNiAl0.3 High Entropy Alloys Reinforced with Cr2O3/Al2O3 Nanoparticles

Effects of Ni Addition and Cyclic Sintering on Microstructure and Mechanical Properties of Coarse Grained WC–10Co Cemented Carbides