Abstract:In order to obtain fine grained structure efficiently, a new multi-step rolling process (MSR: pre-deformation + intermediate annealing + hot deformation) was applied in Al-Zn-Mg-Cu plates. Conventional hot rolling (CHR) was also carried out as a contrast experiment. The evolution of microstructures and improvement of mechanical properties were analyzed by optical microscope, scanning electron microscope, transmission electron microscope, X-ray diffractometer, and tensile tests. The results show that the MSR process can obtain finer longitudinal grain size and better mechanical properties than CHR, which can be explained as follows: spheroidization of precipitates wrapped by high density dislocations could be promoted by increased pre-deformation; numerous ordered substructures were formed during short-period intermediate annealing at high temperature; in the subsequent hot rolling process, the retained spherical precipitates pinned dislocations and boundaries. With the increase of accumulated strain, low angle grain boundaries gradually transformed into high angle grain boundaries, leading to grain refinement. With the increased pre-deformation (MSR1 20 + 60%, MSR2 40 + 40%, MSR3 60 + 20%), the effect of grain refinement and plasticity improvement gradually weakened. The optimum thermomechanical process (MSR1 solid solution + pre-deformation (300 °C/20%) + intermediate annealing (430 °C/5 min) + hot deformation (400 °C/60%)) was obtained, which can increase elongation by ~25% compared with the CHR process, while maintaining similar high strength for reduced longitudinal grain size.

Effect of the Precipitated Phase of MgZn2 on Surface Nanocrystallization of Al-Zn-Mg Alloy Based on High-Frequency Impacting and Rolling

Atomic-scale study on the precipitation behavior of an Al-Zn-Mg-Cu alloy during isochronal aging

Accelerated Precipitation and Growth of Phases in an Al-Zn-Mg-Cu Alloy Processed by Surface Abrasion

Nanocrystallization and precipitation behavior evolution of AZ80 magnesium alloy during multi-directional compression

Distributions of Grains and Precipitates in Gradient Lamellae Al–Zn–Mg–Cu Alloy by Ultrasonic Surface Rolling Processing

Effects of Mg/Zn ratio and pre-aging on microstructure and mechanical properties of Al–Mg–Zn–Cu alloys

Precipitation and aging phenomena in an ultrafine grained Al-Zn alloy by severe plastic deformation

Microstructures and Mechanical Properties of Al-Zn-Mg-Cu Alloys under Multi-Directional Severe Strain and Aging

Recrystallization and Precipitation of Β-Mg17al12 Phase of the Cold-Rolled Mg-9Al-1Zn Alloy Strip During Isothermal Annealing

Characterization of precipitates in aged Mg-4 wt%Zn alloy

Phase transformation from phase to S phase at grain boundary during annealing in rapidly-solidified Al-Zn-Mg-Cu alloy

Effects of Rolling Deformation on Precipitation Behavior and Mechanical Properties of Al–Zn–Mg–Cu Alloy

Promotion Effect of Secondary Phase Particles on Grain Refinement of Deformed Mg–Y–Nd–Zn Alloy

Characterization and Strengthening Effect of Precipitate Microstructure in Mg-3nd-3gd-0.2zn-0.5zr Alloy Aged at 225 °C

Effect of Deformation on Precipitation and the Microstructure Evolution during Multistep Thermomechanical Processing of Al-Zn-Mg-Cu Alloy

Precipitation in an Al-Zn-Mg-Cu alloy during isothermal aging: Atomic-scale HAADF-STEM investigation

Precipitation Behavior and Mechanical Properties of a Mg–Zn–Y–Zr Alloy Processed by Thermo-Mechanical Treatment

Nanoscale Icosahedral Quasicrystal Phase Precipitation Mechanism During Annealing for Mg–Zn–Gd-based Alloys

Nucleation and evolution mechanism of precipitates during the initial aging stage in Al-Zn-Mg-Cu alloy

Influence of Quench-Induced Precipitation on Aging Behavior of Al-Zn-Mg-Cu Alloy

Controllable reinforcement phase distribution at the grain scale via a simple precipitation process