A High Energy Output and Low Onset Temperature Nanothermite Based on Three-Dimensional Ordered Macroporous Nano-Nife2o4

Liming Shi,Wenchao Zhang,Jia Cheng,Chunpei Yu,Ruiqi Shen,Jiahai Ye,Zhichun Qin,Yimin Chao

DOI: https://doi.org/10.1039/c6ra16429c

IF: 4.036

2016-01-01

RSC Advances

Abstract:3DOM Al/NiFe2O4 nanothermite with significantly improved heat output and lower onset temperature.

What problem does this paper attempt to address?

3D ordered macroporous NiO/Al nanothermite film with significantly improved higher heat output, lower ignition temperature and less gas production

Chunpei Yu,Wenchao Zhang,Ruiqi Shen,Xing Xu,Jia Cheng,Jiahai Ye,Zhichun Qin,Yimin Chao

DOI: https://doi.org/10.1016/j.matdes.2016.08.002

IF: 9.417

2016-01-01

Materials & Design

Abstract:The performances of nanothermites largely rely on a meticulous design of nanoarchitectures and the close assembly of components. Three-dimensionally ordered macroporous (3DOM) NiO/Al nanothermite film has been successfully fabricated by integrating colloidal crystal template (CCT) method and controllable magnetron sputtering. The as-prepared NiO/Al film shows uniform structure and homogeneous dispersity, with greatly improved interfacial contact between fuel and oxidizer at the nanoscale. The total heat output of 3DOM NiO/Al nanothermite has reached 2462.27J·g−1 at optimal the deposition time of 20min, which is significantly more than the values of other NiO/Al structural systems that have been reported before. Intrinsic reduced ignition temperature (onset temperature) and less gas production render the wide applications of 3DOM NiO/Al nanothermite. Moreover, this design strategy can also be readily generalized to realize diverse 3DOM structured nanothermites.
Enhancing the Energy Release Performance of Al/CuO Nanothermites through Hierarchical Structure

Qihui Wang,Xiaofeng Sun,Ruozhou Wang,Li Liu,Qi Zhang,Yi Sun,Zhitao Yan,Xueming Li

DOI: https://doi.org/10.1080/00102202.2024.2425359

IF: 1.9

2024-11-13

Combustion Science and Technology

Abstract:The objective of this study is to enhance the mixing uniformity and contact efficiency between nano-Al and oxidizers through structural control, while suppressing the "pre – ignition fusion" effect of nanothermites. We employed biotemplate approach, utilizing Lycopodium japonicum Thunb. spores (LP) and Papilio maackii wings (PW) as sacrificial templates, to successfully fabricate hierarchically structured Al/PW-CuO and Al/LP-CuO nanothermites. At a stoichiometric ratio of Ф = 1.5, Al/PW-CuO exhibited the highest heat release of 2278.00 J/g, whereas Al/LP-CuO also achieved a substantial heat release of 1969.08 J/g. These outstanding performances are attributed to the unique structures of PW-CuO and LP-CuO, especially the spine-like plate structure of PW-CuO, which provides more reaction sites, thereby enhancing spatial utilization and heat release efficiency. This study provides new insights for the design and application of highly active nanoenergetic materials.

energy & fuels,engineering, chemical,thermodynamics, multidisciplinary
Enhancing the energy release performance of nanothermites through metal oxides free oxygen and pores

Wei Shi,Xiwen Wang,Jianyong Xu,Zhiyuan Guan,Qianwen Jiang,Wenchao Zhang,Chunpei Yu,Changkun Song,Junhong Chen

DOI: https://doi.org/10.1016/j.cej.2023.148483

IF: 15.1

2024-01-13

Chemical Engineering Journal

Abstract:Efficient energy release and the large-scale preparation of thermite with high energy density are currently crucial issues in the field of explosive systems. In this study, we focused on the utilization of porous metal oxides (pM x O y ) prepared through urea co-precipitation and high-temperature annealing to enhance the ignition and combustion performance of nanothermites. We compared the thermochemical reactivity, ignition, and combustion performance of nAl/pM x O y with those of nanothermites composed of nano metal oxides. We found that the use of pM x O y resulted in significantly increased the reaction exergy and reduced the activation energy of nanothermites, the energy released by the nanothermite containing pM x O y increased by up to 33.4%, while the activation energy decreased by up to 34.8%. Furthermore, the ignition and combustion results show that better semiconductor bridge ignition, pressurization, and combustion performance of nanothermites consisting of high free oxygen ratio and high porosity pM x O y . This improvement can be attributed to the enhanced contact between nAl and pM x O y , as well as the improved oxygen ionic conductivity of pM x O y . We believe that this high-performance nanothermite, which utilizes porous metal oxides exhibiting high interfacial activity, can be extensively employed in various initiating explosive devices. Notably, the simplicity of the batched preparation process further enhances its potential for practical application.

engineering, chemical, environmental
High dispersity and ultralight PVP-mediated Al/MFe2O4/g-C3N4 (M = Cu, Mg, Ni) nanothermites synthesized by a novel sol-freeze-drying technology

Jingjing Wang,Zhaoqi Guo,Suhang Chen,Yong Chen,Zhao Qin,Kangzhen Xu

DOI: https://doi.org/10.1016/j.apt.2023.103976

IF: 4.969

2023-03-01

Advanced Powder Technology

Abstract:Nanothermite is a reactive system of nanoscale metal-based energetic materials, which is also known as metastable intermolecular composites (MICs). In this study, graphitic carbon nitride (g-C3N4) as a new typical polymer semiconductor was firstly employed to replace GO as an additive in nanothermite. For solving the dispersity of g-C3N4 in nanothermite, a simple and novel sol-freeze-drying technology was firstly proposed to prepare Al/MFe2O4/g-C3N4 (M = Cu, Mg, Ni). The as-prepared Al/MFe2O4/g-C3N4 (M = Cu, Mg, Ni) nanothermites present a similar shape to the host container and have high dispersity, ultralight weight (0.035 g·cm−3) and large specific volume (28.19 cm3·g−1). The optimal PVP and g-C3N4 content were determined. Al/MFe2O4/g-C3N4 (M = Cu, Mg, Ni) all have superior combustion performance, lower electrostatic discharge sensitivity (EDS) and better catalytic performance on ammonium perchlorate (AP) and dihydroxy-lammonium 5,5′-bistetrazole-1,1′-diolate (TKX-50). g-C3N4 plays an important role in suppressing unstable combustion and is beneficial to reduce the electrostatic discharge sensitivity of MICs. This work demonstrates that PVP-mediated sol-freeze-drying technology is an effective approach for obtaining g-C3N4-based nanothermite with high dispersity and ultralight characteristic.

engineering, chemical
Self-assembly preparation of advanced metastable MCo2O4/GO/Al (M=Cu, Mg, Zn, Ni) nanothermites to realize large heat release, stable combustion and high safety

Jingjing Wang,Zhaoqi Guo,Suhang Chen,Wenzhen Zhang,Hu Cui,Zhao Qin,Kangzhen Xu

DOI: https://doi.org/10.1016/j.ceramint.2022.04.070

IF: 5.532

2022-04-01

Ceramics International

Abstract:Metal/oxide-based nanothermite is a kind of metastable intermolecular composites (MICs) whose application performance can be adjusted purposefully by varying properties of oxidizers. Herein, four new MCo2O4/GO/Al (M = Cu, Mg, Zn, Ni) nanothermites were prepared in this work, in which the bimetallic composite oxides of spinel MCo2O4 were employed to replace single metal oxides as oxidizer. The positively charged MCo2O4 and Al nanoparticles were successfully self-assembled by the encapsulation of negatively charged GO. MCo2O4/GO/Al nanothermites present a dense layer stacked structure and uniform distribution, with a favorable interfacial contact between the bimetallic oxide and fuel at the nanoscale. MCo2O4/GO/Al nanothermites release higher energy of about 2500–3400 J g−1, much higher than that of corresponding thermite with single metal oxide. CuCo2O4/GO(2.5 wt%)/Al has the shortest pressure rise time (27.18 ms), largest energy output (3422 J g−1) and peak pressure (6.03 MPa), exhibiting a more violent combustion reaction and higher reactivity. The introduction of GO significantly improves the safety, and the electrostatic discharge sensitivity (EDS) of CuCo2O4/GO(5 wt%)/Al can reach 0.56 mJ, largely higher than that of CuCo2O4/Al without GO (0.04 mJ). MCo2O4/GO/Al nanothermites also have different catalytic performances on energetic components of cyclotrimethylenetrinitramine (RDX), ammonium perchlorate (AP) and dihydroxy-lammonium 5,5′-bistetrazole-1,1′-diolate (TKX-50), indicating the selectivity of catalyst. This study proves that spinel MCo2O4 is a superior oxidizer for Al-based nanothermite system.

materials science, ceramics
A Smart Thermite with Tunable Properties – Doping of Al/Cuo with Microwave Absorbing Ti3c2 Mxene for Improved Ignition and Combustion Performance

Jian Cheng,Zehua Zhang,Yueting Wang,Fuwei Li,Jinle Cao,Michael Gozin,Yinghua Ye,Ruiqi Shen

DOI: https://doi.org/10.2139/ssrn.4123907

2022-01-01

SSRN Electronic Journal

Abstract:Nanothermites have a wide application in many civil and defense applications, including propulsion and detonations systems, micro-electromechanical (MEMs) and other systems that require fast energy release rate and low ignition temperature. Since traditional ignition methods are commonly based on surface excitation (spot ignition), possessing a risk of undesired ignition, safe and selective microwave (MW)-based igniting systems can interact with an ignitable material (typically a thermite) over its full volume at once . Unfortunately, thermites have low susceptibility to MW due to the presence of Al 2 O 3 oxide shell on Al particles, which would commonly require a high ignition power of MW radiation and long ignition delay times. In this work, Ti 3 C 2 MXene was introduced as a MW susceptor into Al/CuO energetic nanocomposite. The samples were ignited using a MW probe, showing that the introduction of MXene into Al/CuO/MXene could significantly reduce a power required for its MW ignition, as well as shorten the ignition delay time versus the parent Al/CuO nanothermite. Presence of MXene could modulate and control a heat release, gas production and combustion performance of the Al/CuO/MXene composites, substantially extending safety, flexibility and adaptability of new nanothermites to various operational requirements.
Nanothermite with Meringue-like Morphology: From Loose Powder to Ultra-porous Objects

Cédric Martin,Marc Comet,Fabien Schnell,Denis Spitzer

DOI: https://doi.org/10.3791/56479

2017-12-24

Abstract:The goal of the protocol described in this article is to prepare aluminothermic compositions (nanothermites) in the form of porous, monolithic objects. Nanothermites are combustible materials made up of inorganic fuel and an oxidizer. In nanothermite foams, aluminum is the fuel and aluminum phosphate and tungsten trioxide are the oxidizing moieties. The highest flame propagation velocities (FPVs) in nanothermites are observed in loose powders and FPVs are strongly decreased by pelletizing nanothermite powders. From a physical standpoint, nanothermite loose powders are metastable systems. Their properties can be altered by unintentional compaction induced by shocks or vibrations or by the segregation of particles over time by settling phenomena, which originates from the density differences of their components. Moving from a powder to an object is the challenge that must be overcome to integrate nanothermites in pyrotechnic systems. Nanothermite objects must have both a high open porosity and good mechanical strength. Nanothermite foams meet both of these criteria, and they are prepared by dispersing a nano-sized aluminothermic mixture (Al/WO3) in orthophosphoric acid. The reaction of aluminum with the acid solution gives the AlPO4 "cement" in which Al and WO3 nanoparticles are embedded. In nanothermite foams, aluminum phosphate plays the dual role of binder and oxidizer. This method can be used with tungsten trioxide, which is not altered by the preparation process. It could probably be extended to some oxides, which are commonly used for the preparation of high performance nanothermites. The WO3-based nanothermite foams described in this article are particularly insensitive to impact and friction, which makes them far safer to handle than loose Al/WO3 powder. The fast combustion of these materials has interesting applications in pyrotechnic igniters. Their use in detonators as primers would require the incorporation of a secondary explosive in their composition.
Ti/CuO and Ti/CuO/Cellulose Nitrate Nanothermites: An Early Insight into Their Combustion Mechanism

Mateusz Polis,Agnieszka Stolarczyk,Konrad Szydło,Tomasz Jarosz,Marcin Procek,Sebastian Sławski,Tomasz Gołofit,Barbara Lisiecka,Łukasz Hawełek

DOI: https://doi.org/10.3390/en17174333

IF: 3.2

2024-09-01

Energies

Abstract:Most nanothermite compositions utilise Al as a fuel, due to its low cost, high reactivity and availability. Nevertheless, aluminothermites exhibit high ignition temperature and low active metal content. In this paper, the combustion behaviour of Ti/CuO and Ti/CuO/NC systems is discussed. The compositions were prepared with a wet-mixing/sonication process followed by an electrospray technique and were examined in terms of their mechanical and radiation sensitivity, energetic parameters and morphology. The results exhibited a strong correlation between equivalence ratio and energetic parameters. The performed tests showed the crucial impact the addiction of the chosen energetic binder on the morphology and performance of the compositions. The results of our experiments indicate the occurrence of a different combustion mechanism than the one observed for Al-based nanothermites. In our case, the combustion mechanism involves a limitation by the diffusion of the oxidising agent and its decomposition products into the reactive fuel core.

energy & fuels
A novel nano-thermite system with BiOF as fluorine-containing oxidant for enhanced energy release performance

Jingwei Li,Xuwen Liu,Qian Huang,Feifan Liu,Quanmin Xie,Maocong Hu,Jiaxin Su,Chengchen Zhang,Yuyang Zeng,Chenguang Zhu

DOI: https://doi.org/10.1016/j.cej.2023.143591

IF: 15.1

2023-06-02

Chemical Engineering Journal

Abstract:The reduced diffusion distance of nano-thermite results in an exceptionally high energy release rate and intense exothermic reactions upon ignition, which has drawn significant interest from researchers in the field of energetic materials. With the deepening of research, metal fluorides are gradually favored by researchers because of their unique reaction characteristics. This paper presents the synthesis of a new fluorine-containing oxidant, BiOF, and its use in the preparation of a novel nano-thermite with n-Al. BiOF crystals exhibit a unique microscopic morphology and are interlaced into "nanoflower" microspheres, which allows for good interfacial contact between the oxidant and fuel during the recombination process. The resulting n-Al/BiOF system displays excellent ignition and combustion performance, with a combustion temperature higher than the boiling point of its main combustion products, AlF 3 and Bi. Compared with n-Al/CuO and n-Al/MoO 3 systems, n-Al/BiOF exhibits a higher flame propagation rate under confinement. In addition, the ignition threshold of the n-Al/BiOF system is also smaller than that of the n-Al/CuO and n-Al/MoO 3 systems. Furthermore, the paper examines the reaction mechanism of the n-Al/BiOF system through thermal reaction path analysis and combustion and thermal analysis product characterization. The paper discovers a "pre-ignition" reaction mechanism before the ignition temperature, where the strongly electronegative fluorine in BiOF corrodes the Al 2 O 3 shell, promoting the release of aluminum energy. The synergistic and effective interaction between oxygen, fluorine, and fuel aluminum in the n-Al/BiOF system results in efficient energy release performance, making BiOF a promising candidate for n-Al based reactive materials in propellants, explosives, and pyrotechnic products.

engineering, chemical, environmental
Facile Formation of Nitrocellulose-Coated Al/Bi2O3 Nanothermites with Excellent Energy Output and Improved Electrostatic Discharge Safety

Ji Dai,Jianbing Xu,Fei Wang,Yu Tai,Yun Shen,Ruiqi Shen,Yinghua Ye

DOI: https://doi.org/10.1016/j.matdes.2018.01.056

IF: 9.417

2018-01-01

Materials & Design

Abstract:Nanothermites are attracting much attention for energetic applications. However, they suffer from high electrostatic discharge (ESD) sensitivity which makes their handling hazardous. Developing safe yet powerful nanothermites is still a challenge. In this work, nitrocellulose (NC) was adhered to the surface of Al and Bi2O3 nanoparticles by a facile electrospray method aiming to improve the ESD safety and energy output of Al/Bi2O3. The morphological and compositional characterization of Al/Bi2O3@NC confirms the NC-coated structure. Benefiting from the structure, the ESD safety of coated Al/Bi2O3 is improved, for instance, the Al/Bi2O3@NC containing 10wt% of NC has a ESD ignition threshold to be 81mJ instead of 1mJ for the Al/Bi2O3 without NC. On the other hand, tunable energy output is obtained by the addition of NC coating. Specifically, Al/Bi2O3@NC (3wt%) exhibits remarkably enhancements in pressurization, combustion reaction and heat release, which even outperforms the most widely used primary explosive lead styphnate (LTNR). The enhancements are attributed to the fact that NC serves as a gas-generating agent to prevent the nanoparticles from sintering to larger particles and enables sufficient combustion. These results suggest that the electrospray formation of NC-coated nanothermites is a facile strategy for obtaining novel nanothermites.
From nanoparticles to on-chip 3D nanothermite: electrospray deposition of reactive Al/CuO@NC onto semiconductor bridge and its application for rapid ignition.

Ji Dai,Cheng-Ai Wang,Yueting Wang,Wei Xu,Jianbing Xu,Yun Shen,Wei Zhang,Yinghua Ye,Ruiqi Shen

DOI: https://doi.org/10.1088/1361-6528/ab6fd8

IF: 3.5

2020-01-01

Nanotechnology

Abstract:Nanothermites composed of nano-fuels and oxidants are attractive energetic materials, which have potential applications in microscale energy-demanding systems. Herein, nano-Al/CuO with nitrocellulose (NC) binder have been bottom-up assembled on semiconductor bridge (SCB) chip by electrospray, from nanoparticles to three-dimensional (3D) deposited structure. The morphological and compositional characterization confirms the constituents in Al/CuO@NC are homogeneously mixed at nano scale and the 3D structure at micro scale is tunable. The as-deposited Al/CuO@NC exhibits excellent energy output and superior chemical reactivity. Specifically, the heat release of Al/CuO@NC (1179.5 J g(-1)) is higher than that of random mixed Al/CuO (730.9 J g(-1)). Benefiting from outstanding exothermic properties, the material integrated with SCB initiator chip (Al/CuO@NC-SCB) for potential ignition application was investigated. The Al/CuO@NC-SCB micro energetic initiator can be functioned rapidly (with delay time of 2.8 mu s) and exhibits superb ignition performances with violent explosion process, high combustion temperature (4636 degrees C) and successful ignition of B/KNO3 propellant, in comparison to SCB initiator. The strategy provides promising route to introduce nano reactive particles into various functional energy-demanding systems for potential energetic applications.
From nanoparticles to on-chip 3D nanothermite: electrospray deposition of reactive Al/CuO@NC onto semiconductor bridge and its application for rapid ignition

Ji Dai,Chengai Wang,Yueting Wang,Wei Xu,Jianbing Xu,Yun Shen,Wei Zhang,Yinghua Ye,Ruiqi Shen

DOI: https://doi.org/10.1088/1361-6528/ab6fd8

IF: 3.5

2020-01-01

Nanotechnology

Abstract:Nanothermites composed of nano-fuels and oxidants are attractive energetic materials, which have potential applications in microscale energy-demanding systems. Herein, nano-Al/CuO with nitrocellulose (NC) binder have been bottom-up assembled on semiconductor bridge (SCB) chip by electrospray, from nanoparticles to three-dimensional (3D) deposited structure. The morphological and compositional characterization confirms the constituents in Al/CuO@NC are homogeneously mixed at nano scale and the 3D structure at micro scale is tunable. The as-deposited Al/CuO@NC exhibits excellent energy output and superior chemical reactivity. Specifically, the heat release of Al/CuO@NC (1179.5 J g(-1)) is higher than that of random mixed Al/CuO (730.9 J g(-1)). Benefiting from outstanding exothermic properties, the material integrated with SCB initiator chip (Al/CuO@NC-SCB) for potential ignition application was investigated. The Al/CuO@NC-SCB micro energetic initiator can be functioned rapidly (with delay time of 2.8 mu s) and exhibits superb ignition performances with violent explosion process, high combustion temperature (4636 degrees C) and successful ignition of B/KNO3 propellant, in comparison to SCB initiator. The strategy provides promising route to introduce nano reactive particles into various functional energy-demanding systems for potential energetic applications.
Energetic properties of new nanothermites based on in situ MgWO4-rGO, CoWO4-rGO and Bi2WO6-rGO

Jingjing Wang,Suhang Chen,Weimin Wang,Fengqi Zhao,Kangzhen Xu

DOI: https://doi.org/10.1016/j.cej.2021.133491

IF: 15.1

2022-03-01

Chemical Engineering Journal

Abstract:The development of nanothermites with high energy release rate is an important direction to the combustion catalysts in solid propellants. Herein, the bimetallic composite oxides (MgWO4, CoWO4 and Bi2WO6) were compounded with GO through an in situ solvothermal method, followed by self-assembly with Al nanoparticles in an organic solvent to obtain a new type of nanothermites. The structure, heat release and ignition performance of MgWO4-rGO/Al, CoWO4-rGO/Al and Bi2WO6-rGO/Al and their catalytic performances on several energetic materials were investigated. All prepared samples present a dense layer stacked structure. The heat outputs of MgWO4-rGO/Al, CoWO4-rGO/Al and Bi2WO6-rGO/Al nanothermites reach 2763.8, 3094.1 and 2853.6 J·g−1 respectively, which are significantly larger than those of Al/CuO (2070.0 J·g−1), Al/Fe2O3 (2088.0 J·g−1), GO/Al/Bi2O3 (1421.0 ± 12.0 J·g−1) and MxWOy/Al without GO. The enhanced performance may be ascribed to the unique structure of bimetallic composite oxides and GO, and uniform compact structure of nanothermites. CoWO4-rGO/Al exhibits a higher combustion heat release (3094.1 J·g−1), shorter ignition delay time (11.0 ms) and burning time (50.0 ± 2.0 ms), the minimum time of reaching the maximum flame area (20.0 ± 2.0 ms) and the maximum flame propagation speed (7.3 ± 0.7 m·s−1), demonstrating outstanding exothermic and combustion properties. The DSC results show that MgWO4-rGO/Al, CoWO4-rGO/Al and Bi2WO6-rGO/Al nanothermites reduce the peak temperature of AP (406.5 °C) by 23.8, 62.2 and 25.5 °C, and RDX by 3.2, 4.5 and 3.3 °C, respectively. This study will provide a new strategy of combustion catalysts utilizing the synergistic effects of energization and nanometerization.

engineering, chemical, environmental
Bio-inspired metastable intermolecular nanothermite composite based on Manganese dioxide/Polydopamine/Aluminium

Sherif Elbasuney,M. Yehia,Gharieb S. El-Sayyad

DOI: https://doi.org/10.1007/s10854-021-05582-6

2021-03-06

Abstract:Surface engineering of energetic particles can offer significant applications; the emergence of surface modification with polydopamine (PDA) can propose novel material science. Even though, nanothermites (metal oxide/metal) can offer surplus heat output; the reaction rate is comparatively-low as it is limited to the interplaner distance between particles. Intimate mixing between metal oxide/metal could be accomplished via surface modification. This study reports on the facile synthesis of MnO2 nanoparticles (NPs) of 5 nm average particle size. On the other hand, Al NPs in the shape of plates of 100 nm particle size were employed. Surface modification of Al NPs with PDA was conducted via in situ polymerization. Colloidal MnO2 NPs integrated into PDA/Al during the polymerization process. DPA layer was effectively-deposited on the aluminium surface and effectively-anchored MnO2 NPs. SEM micrographs of developed MnO2/PDA/Al nanocomposite demonstrated the successful bonding of MnO2 to Al surface via strong PDA chemical bonding. From FTIR spectra, the sharp peaks at 1544 cm−1 and 1389 cm−1 attributed to the C=O and C–O bonds, respectively, and could be due to bond formation between Mn and oxygen in C=O, and C–O in PDA. The developed MnO2/PDA/Al demonstrated the uniform distribution of MnO2 NPs on Al nano-plates. This work dropped the light toward the green production of novel nanothermite hybrid with durable chemical bonding. MnO2/PDA/Al hybrid can offer superior combustion characteristics with intimate mixing between the oxidizer and metal fuel to the molecular level.
Al/CuF 2 Composite Materials with Ignition Characteristics and Pressure Output Ability for Nanothermites

Jie Ji,Rui Cui,Li Liang,Heng Xu,Haozhe Li,Xiang Ke,Xiang Zhou,Xiaode Guo

DOI: https://doi.org/10.1021/acsanm.2c04980

IF: 6.14

2023-02-09

ACS Applied Nano Materials

Abstract:To improve the pressure output ability of nanothermites to meet the needs in many fields, with the more volatile advantage of metal fluoride products (AlF3), this paper proposes the scheme of nanothermites (Al/CuF2). The energy release process of Al/CuF2 with different equivalent ratios under slow and fast heating rates has been studied. Under the slow heating rates, it was found that the equivalent ratio (Φ) has a significant influence on the energy release process. When Φ ≤ 1, the product is dominated by Cu. With the increase of the equivalent ratio, Al2Cu gradually appeared in the product, indicating that the increase of Al powder contributed to the enhancement of the alloy reaction. On the other hand, to further investigate the actual application of the Al/CuF2 mixture, combustion experiments in a closed container and in open air were carried out and compared with those of Al/CuO. In accordance with our design concept, AlCuF2 shows more excellent gas release ability. Al/CuF2 (Φ = 3) has the most excellent pressure output capacity (2.67 MPa), which increases by 107% compared to 1.29 MPa (Al/CuO). In addition, Al/CuF2 displays more excellent ignition performances in terms of shorter delay time and less ignition energy. Therefore, Al/CuF2 composite particles, as a novel nanothermite design, are expected to be widely used in the gas generator, micropropulsion, and other military and civilian fields.

materials science, multidisciplinary,nanoscience & nanotechnology
Pushing the Limits of Energy Performance in Micron-Sized Thermite: Core–Shell Assembled Liquid Metal-Modified Al@Fe2O3 Thermites

An Chen,Bo Wu,XiaoDong Li,Jinpeng Shen,Lu Tian,Yong Zhou,Chonghua Pei

DOI: https://doi.org/10.1021/acsaem.1c02549

IF: 6.4

2021-01-01

ACS Applied Energy Materials

Abstract:Thermites are a class of significant energetic materials widely used in aerospace propulsion, explosion, pyrotechnics, thermal batteries, and power generation. Although nanothermites exhibit fast reaction rates and high energy density, micron-sized thermites remain of practical importance over nanothermites due to their low electrostatic discharge (ESD) sensitivity, lower cost, and smaller dead mass. Herein, we develop micron-sized core-shell gallium-based liquid metal-modified Al@Fe2O3 (GLM-Al@Fe2O3), which exhibits high energy density and low laser ignition energy. At an equivalence ratio of 1.3, the differential scanning calorimetry results show that the total heat release of GLM-Al@Fe2O3 reaches 2555 J.g(-1), which is much higher than that of the control sample (1424 J.g(-1)) prepared by a similar process. The density of GLM-Al@Fe2O3 (f = 1.3) was characterized by a gas pycnometer analyzer, and its volumetric energy density could reach 9.96 kJ.cm(-3). Laser-ignited combustion performance of GLMAl@Fe2O3 was markedly reinforced in terms of the decreased ignition energy. Additionally, the ESD ignition threshold of GLM-Al@Fe2O3 is higher than 1 J, which revealed that the as-prepared GLM-Al@Fe(2)O(3)was insensitive to electrostatic discharge. The facile and efficient strategy in this work provides inspiration to enhance the energy output performance and maintain the ESD safety of micron-sized thermites, which could show great potential in various civilian and military applications.
Study on combustion characteristics and pyrotechnic cutting effects of bimetal thermite Ni/Al/Fe2O3 system

Mi Li,Zhongxuan Han,Lin Jiang,Guozhong Xu

DOI: https://doi.org/10.1002/prep.202300285

IF: 2.134

2024-04-24

Propellants Explosives Pyrotechnics

Abstract:Nano‐thermite has become a subject of significant interest in the composite energetic materials field due to its high energy release rate. To cater to diverse engineering needs, thermite formulations are often customized to fulfill specific criteria. This study investigates the potential of metal nickel (Ni) as an additive to modify nano‐thermite formulations, selected for its optimal calorific values and chemical reactivity. The base materials, nano‐aluminum (Al) and iron oxide (Fe2O3), are blended with varying mass ratios of Ni (1 %, 3 %, 5 %, 7 %, 9 %) using the wet ball milling method. Pre‐reaction and post‐reaction morphological and compositional alterations in the resultant thermite samples are scrutinized through SEM and XRD characterization tests. Moreover, DSC analysis and combustion experiments were conducted to examine the pyrolysis and combustion behaviors of the evaluated samples. The results reveal a reduced exothermic peak on the DSC curves with the introduction of Ni, making the liquid‐solid (L‐S) phase reaction more challenging compared to the Al/Fe2O3 thermite. Intriguingly, Ni addition progressively decreases the combustion temperature of thermites as the Ni's mass ratio increases, with a peak efficiency at 7 % in the perforation tests on stainless‐steel plates. This research further reveals that the thermite reaction mechanism is a combined consequence of the "pre‐ignition‐fusion" and "fusion‐diffusion" mechanisms. These insights can provide valuable guidance for designing thermite formulations for potential applications in storage, management, and pyrotechnic cutting areas.

engineering, chemical,chemistry, applied
Aluminum/lead tetroxide nanothermites for semiconductor bridge applications

Chunpei Yu,Zilong Zheng,Bonan Gu,Yajie Chen,Jianyong Xu,Lin Zhang,Wei Shi,Jiaxin Wang,Changkun Song,Junhong Chen,Kefeng Ma,Wenchao Zhang,Chunpei Yu,Zilong Zheng,Bonan Gu,Yajie Chen,Jianyong Xu,Lin Zhang,Wei Shi,Jiaxin Wang,Changkun Song,Junhong Chen,Kefeng Ma,Wenchao Zhang

DOI: https://doi.org/10.1016/j.cej.2022.138614

IF: 15.1

2023-01-01

Chemical Engineering Journal

Abstract:Renewed interest in exploiting the full potential of nanothermites has been observed, considering that typical nanothermite powders are prone to get agglomerated and react incompletely. Herein, via direct ink writing, the fabrication of nanothermite films and their integration on semiconductor bridges come true simply and efficiently, keeping nanoscale agents spatially uniform and therefore chasing for reinforced output capability. The key ingredients are Al/Pb3O4 nanothermites and such ink formulation features higher particle loading (95 wt%) than that previously reported in the literature. Experimental results show that the maximum output energy of the Al/Pb3O4 nanothermite inks reaches 1960 J g−1, while the average linear burning rate maintains nearly 19.14 cm s−1. Furthermore, the lab-on-a-chip integration of nanothermite films prominently enhances the energy yield of semiconductor bridges (up to 282 mJ). It turns out that Al/Pb3O4 nanothermite inks show great potential for applications on semiconductor bridges due to their remarkable output performance.

engineering, chemical, environmental
High speed 2-dimensional temperature measurements of nanothermite composites: Probing thermal vs. Gas generation effects

Rohit J. Jacob,Dylan J. Kline,Michael R. Zachariah

DOI: https://doi.org/10.1063/1.5021890

IF: 2.877

2018-03-21

Journal of Applied Physics

Abstract:This work investigates the reaction dynamics of metastable intermolecular composites through high speed spectrometry, pressure measurements, and high-speed color camera pyrometry. Eight mixtures including Al/CuO and Al/Fe2O3/xWO3 (x being the oxidizer mol. %) were reacted in a constant volume pressure cell as a means of tuning gas release and adiabatic temperature. A direct correlation between gas release, peak pressure, and pressurization rate was observed, but it did not correlate with temperature. When WO3 was varied as part of the stoichiometric oxidizer content, it was found that Al/Fe2O3/70% WO3 achieved the highest pressures and shortest burn time despite a fairly constant temperature between mixtures, suggesting an interplay between the endothermic Fe2O3 decomposition and the higher adiabatic flame temperature sustained by the Al/WO3 reaction in the composite. It is proposed that the lower ignition temperature of Al/WO3 leads to the initiation of the composite and its higher flame temperature enhances the gasification of Fe2O3, thus improving advection and propagation as part of a feedback loop that drives the reaction. Direct evidence of such gas release promoting reactivity was obtained through high speed pyrometry videos of the reaction. These results set the stage for nanoenergetic materials that can be tuned for specific applications through carefully chosen oxidizer mixtures.

physics, applied
Quo Vadis, Nanothermite? A Review of Recent Progress

Mateusz Polis,Agnieszka Stolarczyk,Karolina Glosz,Tomasz Jarosz

DOI: https://doi.org/10.3390/ma15093215

2022-04-29

Abstract:One of the groups of pyrotechnic compositions is thermite compositions, so-called thermites, which consist of an oxidant, usually in the form of a metal oxide or salt, and a free metal, which is the fuel. A characteristic feature of termite combustion reactions, apart from their extremely high exothermicity, is that they proceed, for the most part, in liquid and solid phases. Nanothermites are compositions, which include at least one component whose particles size is on the order of nanometers. The properties of nanothermites, such as high linear burning velocities, high reaction heats, high sensitivity to stimuli, low ignition temperature, ability to create hybrid compositions with other high-energy materials allow for a wide range of applications. Among the applications of nanothermites, one should mention igniters, detonators, microdetonators, micromotors, detectors, elements of detonation chain or elements allowing self-destruction of systems (e.g., microchips). The aim of this work is to discuss the preparation methods, research methods, direction of the future development, eventual challenges or problems and to highlight the applications and emerging novel avenues of use of these compositions.

A High Energy Output and Low Onset Temperature Nanothermite Based on Three-Dimensional Ordered Macroporous Nano-Nife2o4

3D ordered macroporous NiO/Al nanothermite film with significantly improved higher heat output, lower ignition temperature and less gas production

Enhancing the Energy Release Performance of Al/CuO Nanothermites through Hierarchical Structure

Enhancing the energy release performance of nanothermites through metal oxides free oxygen and pores

High dispersity and ultralight PVP-mediated Al/MFe2O4/g-C3N4 (M = Cu, Mg, Ni) nanothermites synthesized by a novel sol-freeze-drying technology

Self-assembly preparation of advanced metastable MCo2O4/GO/Al (M=Cu, Mg, Zn, Ni) nanothermites to realize large heat release, stable combustion and high safety

A Smart Thermite with Tunable Properties – Doping of Al/Cuo with Microwave Absorbing Ti3c2 Mxene for Improved Ignition and Combustion Performance

Nanothermite with Meringue-like Morphology: From Loose Powder to Ultra-porous Objects

Ti/CuO and Ti/CuO/Cellulose Nitrate Nanothermites: An Early Insight into Their Combustion Mechanism

A novel nano-thermite system with BiOF as fluorine-containing oxidant for enhanced energy release performance

Facile Formation of Nitrocellulose-Coated Al/Bi2O3 Nanothermites with Excellent Energy Output and Improved Electrostatic Discharge Safety

From nanoparticles to on-chip 3D nanothermite: electrospray deposition of reactive Al/CuO@NC onto semiconductor bridge and its application for rapid ignition.

From nanoparticles to on-chip 3D nanothermite: electrospray deposition of reactive Al/CuO@NC onto semiconductor bridge and its application for rapid ignition

Energetic properties of new nanothermites based on in situ MgWO4-rGO, CoWO4-rGO and Bi2WO6-rGO

Bio-inspired metastable intermolecular nanothermite composite based on Manganese dioxide/Polydopamine/Aluminium

Al/CuF 2 Composite Materials with Ignition Characteristics and Pressure Output Ability for Nanothermites

Pushing the Limits of Energy Performance in Micron-Sized Thermite: Core–Shell Assembled Liquid Metal-Modified Al@Fe2O3 Thermites

Study on combustion characteristics and pyrotechnic cutting effects of bimetal thermite Ni/Al/Fe2O3 system

Aluminum/lead tetroxide nanothermites for semiconductor bridge applications

High speed 2-dimensional temperature measurements of nanothermite composites: Probing thermal vs. Gas generation effects

Quo Vadis, Nanothermite? A Review of Recent Progress