Abstract:TC31 is a new type of α+β dual phase high temperature titanium alloy, which has a high specific strength and creep resistance at temperatures from 650 °C to 700 °C. It has become one of the competitive candidates for the skin and air inlet components of hypersonic aircraft. However, it is very difficult to obtain the best forming windows for TC31 and to form the corresponding complex thin-walled components. In this paper, high temperature tensile tests were carried out at temperatures ranging from 850 °C to 1000 °C and strain rates ranging from 0.001 s−1 to 0.1 s−1, and the microstructures before and after deformation were characterized by an optical microscope, scanning electron microscope, and electron back-scatter diffraction. The dynamic softening and hardening behaviors and the corresponding micro-mechanisms of a TC31 titanium alloy sheet within hot deformation were systematically studied. The effects of deformation temperature, strain rate, and strain on microstructure evolution were revealed. The results show that the dynamic softening and hardening of the material depended on the deformation temperature and strain rate, and changed dynamically with the strain. Obvious softening occurred during hot tensile deformation at a temperature of 850 °C and a strain rate of 0.001 s−1~0.1 s−1, which was mainly caused by void damage, deformation heat, and dynamic recrystallization. Quasi-steady flowing was observed when it was deformed at a temperature of 950 °C~1000 °C and a strain rate of 0.001 s−1~0.01 s−1 due to the relative balance between the dynamic softening and hardening. Dynamic hardening occurred slightly with a strain rate of 0.001 s−1. Mechanisms of dynamic recrystallization transformed from continuous dynamic recrystallization to discontinuous dynamic recrystallization with the increase in strain when it was deformed at a temperature of 950 °C and a strain rate of 0.01 s−1. The grain size also decreased gradually due to the dynamic recrystallization, which provided an optimal forming condition for manufacturing thin-walled components with the desired microstructure and an excellent performance.

Research on forming performance of TA1 and the application in microneedle forming

Research on forming performance of TA1 subjected to ultrasonic vibration

Numerical Modeling and Experimental Study of Microstamping Process for Fabricating Microchannels Using Thin Sheets of Titanium

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

The Formability of Perforated TA1 Sheet in Single Point Incremental Forming

An Experimental and Simulation Study on the Formability of Commercial Pure Titanium Foil

Change in geometry size and thinning rate in single-point incremental forming process of TA1 sheet: evaluation method and finite element analysis

Study of Size Effects on Deformation Behavior and Formability in Micro Metal Forming of Ti Foil

Effect of Pre-Strain on Microstructure and Stamping Ability of TA2 Titanium Alloy and H260 Low-Alloy Steel

Revealing Mechanism of Ductility Improvement of Titanium Thin Sheet under Normal Stress at Mesoscale from Perspective of Microstructure Evolution

Mechanical Behaviour and Strain Rate Sensitivity Analysis of TA2 by the Small Punch Test

Influence of Initial Textures on Microstructure and Mechanical Properties of Commercially Pure TA2 Titanium Sheet Pre-Strained by Cryorolling

Experimental Study on Pure Titanium Subjected to Different Combined Tension and Torsion Deformation Processes

Effect of Microstructure on High-Speed Tensile Mechanical Properties of Ti-1300 Alloy

Formability and Mechanism of Ultra-Thin Titanium Foil under the Elevated Temperature and High Strain Rate in Electromagnetic Forming

Study of Microstructure and Mechanical Properties by Torsional Behavior in Axial Closed Die Rolling Forming

Evolution of microstructure, macrotexture and mechanical properties of high strength biomedical TA4 pure titanium during multi-pass ECAP

Forming Analysis and Heat Treatment of TC31 Titanium Alloy Component with High Ribs and Thin Webs

Dynamic Softening and Hardening Behavior and the Micro-Mechanism of a TC31 High Temperature Titanium Alloy Sheet within Hot Deformation

Microstructures and mechanical properties of commercial purity Ti rolled at room temperature

Comparative study of the strain and strain rate hardening mechanisms and its workability during hot deformation of TC4 titanium alloys