Abstract:Fischer-Tropsch synthesis (FTS) is a classical topic of great significance because of the approach of post-petroleum times. Recently we found that, taking the advantage of the anchoring effect and intrinsic basicity of nitrogen-doped carbon nanotubes (NCNTs), iron nanoparticles could be conveniently immobilized on the NCNTs without surface pre-modification. The so-constructed Fe/NCNTs catalyst presents the superb catalytic performance in FTS with high selectivity as well as high catalytic activity and stability. In this study, three Fe/NCNTs catalysts were prepared by incipient wetness impregnation method, colloidal method and deposition-precipitation method, denoted as Fe/NCNTs-IWP, Fe/NCNTs-C, and Fe/NCNTs-DP, respectively. The influence of preparation methods on the particle size distribution and morphology, reduction and carbonization of the active species, as well as the FTS catalytic performance were systematically examined. The results indicate that the incipient impregnation method could achieve high dispersion, smaller particles and narrower size distribution [(8 +/- 4) nm], leading to the easier reduction and carbonization of the iron nanoparticles compared with those prepared by the other two methods. The FTS catalytic performance of the Fe/NCNTs-IWP catalyst is much better than those of the Fe/NCNTs-C and the Fe/NCNTs-DP catalysts in terms of the high lower olefins selectivity, high catalytic activity and stability. Colloid method got the different morphologies of iron particles with the average size of (13 +/- 7) nm. The active iron species was susceptible to oxidation during the reaction, which cause poor catalytic activity and stability. The deposition-precipitation method got the largest particles of (19 +/- 11) nm which were difficult to be reduced and carbonized, leading to the sharp decline of the catalytic activity and stability after 15 h reaction. The size-dependence of the catalytic performance for the Fe/NCNTs catalysts in this study are generally in consistent with those in literatures for the iron catalysts supported on carbon nanotubes. These results should be suggestive for exploring the advanced FTS catalysts with the abundant N-doped carbon nanostructures.

Carbon Nanotubes Preparation in Industrial Vice-Products

RESEARCH ONPROCESS PARAMETERS FORCARBON NANOTUBES PREPARATION IN INDUSTRIAL VICE-PRODUCTS

Influence of Mesoporous Materials on the Preparation of Carbon Nanotubes

Preparation of Carbon Nanotubes at the Surface of Fe/SBA-15 Mesoporous Molecular Sieve

High-Yield Production of Multi-Walled Carbon Nanotubes by Catalytic Decomposition of Benzene Vapor

Preparation of High Purity Carbon Nano -Tubes from Ethylene Decomposition over Nanosized Iron- Based Catalysts

Preparation of Double-Walled Carbon Nanotubes

Large-Scale Synthesis and Magnetic Property of Carbon Nanotubes

Synthesis of Multi-wall Carbon Nanotubes Using Fe/CNTs As Catalyst

Influence of Preparation Methods on Catalytic Performance of Fe/Ncnts Fischer-Tropsch Catalysts

High-yield production of quasi-aligned carbon nanotubes by catalytic decomposition of benzene

Preparation of carbon nanofibers by the floating catalyst method

Preparation of Nanosized Iron Catalyst and Small Diameter Carbon Nanotubes from Methane Decomposition

Solvothermal Preparation of Amorphous Carbon Nanotubes and Fe/C Coaxial Nanocables from Sulfur, Ferrocene, and Benzene

Synthesis and Characterization of Multi-wall Carbon Nanotubes Using Innoxious Liquid Paraffin As Carbon Source

Controllable growth of double wall carbon nanotubes in a floating catalytic system

Preparation and Growth Mechanism of Carbon Nanotubes Via Catalytic Pyrolysis of Phenol Resin

Converting Carbon Dioxide into Carbon Nanotubes by Reacting with Ethane

Byproducts of Floating Catalyst Method for Preparing Carbon Nanotubes

Preparation and Purification of Carbon Nanotubes by Catalytic Decomposition