Abstract:Ultrafine grained (UFG) metallic materials arouse a great interest clue to their excellent mechanical properties. The UFG materials, produced by severe plastic deformation (SPD) technique such as channel angular pressing (ECAP) and high pressure torsion (HPT), exhibit obvious improvement in strength but a large decrease in their thermal stability and ductility. In this article; an UFG QBel.7 copper alloy with good comprehensive properties was prepared by multi directional compression (MDC) at room temperature and subsequent annealing at high temperature. The deformed and subsequent annealed microstructures were investigated by OM, TEM and SEM/EBSD techniques. The integrated flow curves plotted over a number of compression passes increase to a. maximum at moderate strains of 1 to 2 followed by steady state like flow at high cumulative strains. Fine grains were not observed even at a higher cumulative stain of Sigma epsilon=4.8, although there were many sub grains when the samples were deformed to Sigma epsilon=2.4. This indicates that the dynamic recrystallization or recovery was completely inhibited by Fine precipitates. Static recrystallization (SRX) of the MDCed structure at 973 K was also investigated. With the increment of cumulative strains, the effect of grain refinement became more obvious, but the thermal stability was getting worse. At a medium strain of Sigma epsilon=2.4, the minimal grain size of 0.8 mu m could be developed with an excellent combination of properties. The formation of ultrafine grains is attributed to the development from low angle boundaries to medium angle boundaries to large angle boundaries. The change of the average grain size with annealing time could be divided into three, stages: a recovery period for grain refinement, rapid grain refinement and normal grain growth.

Research and Development of Ultrafine-Grained Materials Fabricated by Cyclic Extrusion Compression

Strengthening and Toughening Mechanisms of an Ultrafine Grained Mg-Gd-Y-Zr Alloy Processed by Cyclic Extrusion and Compression

Research progress of fabricating ultrafine-grained composites by severe plastic deformation

Manufacturing of fine-grained structures by multilevel kinking mechanism through a novel periodic undulating compression method: An example 7075 aluminum alloy

Research and Development Prospects of Ultrafine-Grained Materials Fabricated by Severe Plastic Deformation

Influence of Grain Refinement and Texture Evolution on the Yield Strength of Mg Alloy Processed by Cyclic Extrusion and Compression

Preparation of Ultrafine-Grained Copper Alloy by Annealing Treatment after Multi-Directional Compression

Abnormal Grain Growth: A Potential Way to Construct Gradient Structure

Microstructure Evolution and Mechanical Properties of an Az61 Mg Alloy Through Cyclic Extrusion Compression

Compression-torsion forming experiment and die design

Study on Micro Scale Extrusion Forging Process

Microstructure and texture evolution during compression-extrusion process for tension/compression symmetrical ZK61 magnesium alloy rod

Microstructure and Texture Characteristics of Zk60 Mg Alloy Processed by Cyclic Extrusion and Compression

Precipitation behavior and its effect on the dynamic recrystallization of a novel extruded Al-Cu-Li alloy

Grain Refinement in Surficial Cryogenic Grinding

Microstructural Evolution at Micro/Meso-Scale in an Ultrafine-Grained Pure Aluminum Processed by Equal-Channel Angular Pressing with Subsequent Annealing Treatment

Finite Element Analysis of Strain Distribution in ZK60 Mg Alloy During Cyclic Extrusion and Compression

Grain Refinement of Magnesium Alloys Processed by Severe Plastic Deformation

Network-shaped Fine-Grained Microstructure and High Ductility of Magnesium Alloy Fabricated by Cyclic Extrusion Compression

Microstructure and Enhanced Mechanical Properties of an Mg–10Gd–2Y–0.5Zr Alloy Processed by Cyclic Extrusion and Compression

Research and Development Prospects of High Strength Mg Alloys Fabricated by Severe Plastic Deformation