Abstract:Offshore steels for cold climate conditions require not only relatively high strength to improve the cost-efficiency of the structures, but also excellent toughness at low temperatures to guarantee the safety of the structures in harsh environments. The most challenging locations to fulfil both requirements are in the welded joints of these steels because the weld thermal cycles cause detrimental changes to the steel microstructure. Titanium and niobium are often used in these steels to form nanoscale precipitates and reduce austenite grain growth during the thermal cycle. However, there is a risk that in addition to the nanoscale precipitates formed from the solid state, microscale coarse inclusions are also formed from the melt. These inclusions are hard and brittle and thus likely to deteriorate mechanical properties such as fracture toughness and impact toughness. In this study, two experimental 500 MPa offshore steels with differing inclusion structures were studied to find out if titanium based nitrides significantly deteriorate the fracture toughness of the coarse grained heataffected zone (CGHAZ) at -40 °C. A Gleeble 3800 was used to simulate the CGHAZ, and the fracture toughness was determined by three point bending testing. Inclusions were characterized using FESEM-EDS. It was found that fracture toughness of the steel with coarse nitrides was lower and the scatter higher than in the steel with a higher calcium based inclusion content and without the coarse nitrides. Fractographic examination showed that the failure in the samples with the lowest toughness was initiated by coarse titanium-niobium nitrides. To avoid toughness problems caused by the CGHAZ under cold conditions, it is necessary to prevent the formation of coarse nitrides during steel production.

Factors Influencing Notch Toughness of Coarse-grained Heat Affected Zone for 9% Ni Steel

Process Routes of Low‐Ni Liquefied Natural Gas Tank Steel with Excellent Cryogenic Toughness

Effect of Microstructure Synergism on Cryogenic Toughness for CGHAZ of Low-Carbon Martensitic Steel Containing Nickel

Cryogenic Fracture Toughness of 9%ni Steel Flux Cored Arc Welds

The Influence of Microstructure Evolution in Thick Plate 9%ni Steel Submerged Arc Welding Joint on Fracture Toughness Properties

Microstructure and Low-Temperature Toughness of Reheated Coarse-Grained Heat-Affected Zone of 06Ni9DR Steel

Effect of grain size and segregation on the cryogenic toughness mechanism in heat-affected zone of high manganese steel

The Cryogenic Low-Cycle Fatigue Performance of 9%ni Steel Joint Made by Flux Cored Arc Welding

Toughness of Heat-Affected Zone of 800 Mpa Grade Low Alloy Steel

Low-cycle Fatigue and Fracture Behaviour of 9%ni Steel Flux Cored Arc Welding Joint at Cryogenic Temperature

Effect of Quenching, Lamellarizing, and Tempering on Reversed Austenite and Cryogenic Toughness of 9Ni Steels

Correlations of Ni Contents, Formation of Reversed Austenite and Toughness for Ni-Containing Cryogenic Steels

Influence of Direct Lamellarizing-Tempering Process Parameters on Microstructure and Properties of 9 Ni Steel

Influence of Carbon Migration on the Toughness of Heat Affected Zone of 9%cr+2.25%cr Dissimilar Welds at High Temperature

Microstructure Characteristics and Properties of Fusion Boundary in 9%ni Steel Joint Filled with Ni-based Alloy

Effect of Gradient Microstructure and Strength Mismatch on Cryogenic Toughness of Fe-Ni Fusion Boundary

Investigation on the weakest zone in toughness of 9Cr/NiCrMoV dissimilar welded joint and its enhancement

Effects of Small Ni Addition on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of High-Strength Low-Alloy Steel

Precipitation behavior of carbides and cryogenic toughness in heat-affected zone of high-Mn twinning-induced plasticity steel welded joint

Detrimental effect of coarse titanium-niobium nitrides on the fracture toughness of the CGHAZ in a 500 MPa offshore steel for cold climate conditions

Effect of Initial Microstructure on the Toughness of Coarse-Grained Heat-Affected Zone in a Microalloyed Steel