Abstract:The High Intensity Heavy Ion Accelerator Facility (HIAF) is a new engineering project proposed by Institute of Modern Physics (IMP) of China. Various types of superconducting wires with the matrix of CuNi alloy for HIAF project were successfully developed by WST. NbTi/Cu5Ni superconducting wires with filaments number of 10800, 12960, 15984, 23760, 36720 and 44064 were designed and fabricated by a double stacking method. In this study, the microstructure and influence of a heat treatment on the critical current density, hysteresis loss and number of breaks of NbTi/Cu5Ni superconducting wire are investigated. It is demonstrated that when the number of heat treatments increases from 3 to 5, the critical current density increases from 2324 to 2699 A/mm 2 at 5T&4.2K for a 10800-filament wire. However, the number of breaks per one billet increases from 0 to 3. The maximum and minimum piece length is 3500 and 1000 m, respectively. The Nb barrier fracture results in the formation of the Ti-Cu compound between NbTi filaments and Copper during intermediate heat treatment. By reducing the Cu/Sc of sub-elements and improving the Cu shell thickness of the final billet, the deformation of outer filament is relatively favorable, which can enhance the critical current density and reduce hysteresis loss. The critical current density of six designed wires is between 2600 and 2700 A/mm 2 and `n' value is between 35 and 48 at 5T&4.2K, indicating a high filament quality and that no filament breakage occurs in the wire. The Cu5Ni alloy is regarded as the inter-filament matrix to reduce inter-filament coupling currents loss. When the filament number increases from 10800 to 44064 and the diameter of NbTi filament reduces from 4.5 to 2.5 μm, the hysteresis losses reduce from 38.5 to 26.2 mJ/cm 3 at ±3T. The average piece length of six designed wires is more than 2000 m, revealing the ability of mass production for WST. After 5 years investigations WST have developed several designs and the fabrication technology of this type of wire and can completely satisfy the requirements of HIAF magnets.

A Study on Critical Current and AC Loss Characteristics of Novel 2G HTS Narrow Wires

Ac Loss Characteristics of Hts Wires Carrying Currents with Different Waveforms

Evaluation Of Electrical And Mechanical Characteristics For A Twisted Soldered-Stacked-Square (3s) Hts Wire With 1 Mm Width

Experimental Study on AC Loss of 1G and 2G HTS Coils with an Identical Structure, Geometry and Number of Turns

Computation of AC Loss of HTS Coils Wound by Coated Conductors with Different Widths

AC Losses Analysis of HTS Composite Conductors with Different Current Ramp Rates

Influence of Substrates in Hts Wires on Ac Loss Characteristics of Cylindrical Single Layer Conductors

Investigation on the transportation properties of high temperature superconducting wires in low parallel magnetic fields and its significance in cable applications

Investigation on AC Loss of a High Temperature Superconducting Tri-Axial Cable Depending on Twist Pitches

An Experimental Investigation of Critical Current and Current Distribution Behavior of Parallel Placed HTS Tapes

A Study on AC Losses of HTS Pentagonal Conductors Consisting of 2G Wires Carrying DC Offset Transport Current

Numerical Study On Ac Loss Of An Hts Coil Placed On Laminated Silicon Steel Sheets With Distorted Ac Transport Currents

Influence of New Wire Structure on AC Loss of High-Temperature Superconducting Cables

Influence of Transport Modes on AC Loss Characteristics of Cylindrical Single-Layer Conductors Consisting of Various HTS Tapes

Study on High JC and Low AC Loss NbTi/Cu5Ni Superconducting Wire for HIAF Magnets in WST

AC Loss Investigation for Stacked HTS Cables with Gap Optimization

Numerical Investigation of Critical Current and Magnetization Loss Effect for Twisted Stacked Tape Cable Considering Field-Angle Dependency and Mechanical Torsion Degradation

Study on the Current Distribution and Structural Optimization of a High-Temperature Superconducting AC Power Cable

The Technology of Fabrication & Application of Bi-2223 HTS Wires at InnoST

Study on the Influence of HTS Strip and Harmonics on AC Loss of HTS Transformer

Critical Current Degradation Caused By Winding Process Of Bi-2223/Ag Hts Wire In The Form Of A Coil