Abstract:Nanothermites possess much attentions relying on potential probability to the fields of the military and civilian. Whereas, the practical applications for nanothermites have been limited by the high electrostatic discharge (ESD) sensitivity and little gas generation, which is a pronounced problem in the microthruster particularly. In this work, the two typical nanothermites (Al/CuO and Al/MoO3, as Al/MXOY) were assembled with various contents of CL-20 to be defined Al/MXOY@CL-20. The characteristics of Al/MXOY@CL-20 were examined by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), powder X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The ignition properties of Al/MXOY@CL-20, such as burning rate, the unrestrained combustion, ignition temperature, delay time, pressurization and propulsion properties, were studied. In addition, the energy required for 50% ignition probability (E-50) was applied to evaluating the sensitivity of Al/MXOY@CL-20 to ESD. Results revealed that the total heat release for Al/MXOY@CL-20 was increased on account of CL-20, and CL-20 facilitated the transformation of CuO to Cu2O. The burning rates decreased with the increase of CL-20, whereas the burning rate of Al/MoO3@10%CL-20 was little higher than that of Al/MoO3. Al/CuO@10%CL-20 and Al/MoO3@30%CL-20 exhibited superior performances respectively for the maximum flame area, the lowest ignition temperature, the highest pressurization rate and specific impulse. The particular significance was that CL-20 played a positive role for Al/MXOY@CL-20 on the safety to ESD. For instance, the E-50 of Al/CuO@50%CL-20 was 163.84 mJ meanwhile Al/CuO of that was 0.24 mJ. In conclusion, in the light of the superior specific impulse and the excellent safety to ESD, Al/MXOY@CL-20 (especially Al/CuO@10%CL-20 and Al/MoO3@30%CL20) would possess the remarkable application prospects for practice in the microthruster. (c) 2022 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Design, Preparation, and Performance of a Planar Ignitor Inserted with PyroMEMS Safe and Arm Device

Research on a MEMS pyrotechnic with a double-layer barrier safety and arming device

Shape Memory Alloy Safety Device with Zr-BaCrO_4 Heat Paper

A Micro-Initiator Realized by In-Situ Synthesis of Three-Dimensional Porous Copper Azide and Its Ignition Performance

Tuning the Ignition Performance of A Microchip Initiator by Integrating Various Al/Moo3 Reactive Multilayer Films on A Semiconductor Bridge

Design of an Intelligent MEMS Safety and Arming Device with a Condition Feedback Function

High-safety energetic micro-igniter for micro-thrust system

Fabrication of Micro-Ignition Sequence Based on Electronics Safety and Arming Unit

Design and optimization of micro-semiconductor bridge used for solid propellant microthrusters array

Identifying the Enhancement Mechanism of Al/MoO3 Reactive Multilayered Films on the Ignition Ability of Semiconductor Bridge Using a One-Dimensional Gas-Solid Two-Phase Flow Model

Design and Performance of a Micro-Scale Detonation Train with a Built-in Pyrotechnic MEMS-based Safety and Arming Device

Design of a Double-Layer Electrothermal MEMS Safety and Arming Device with a Bistable Mechanism

Investigation on Combustion of Porous Silicon Nanoenergetic Chips Ignited by Single Pulse Laser

Predicting the electromechanical properties of small caliber projectile impact igniter using PZT dynamic damage constitutive model considering crack propagation

In-situ synthesis of MEMS compatible Al/Cu2HIO6/PVDF Metastable composites film with high combustion performance

Superior Performance of a MEMS-based Solid Propellant Microthruster (SPM) Array with Nanothermites

Design and Modeling of MEMS-based Solid Propellant Propulsion

Enhanced Catalytical and Photothermal Behavior Derived from Self‐Assembly Microsuperlattices of Cu 1.8 S for Laser Ignition

An Excellent Synergy Between CL-20 and Nanothermites in Flaming and Propelling with High Specific Impulse and Superior Safety to Electrostatic Discharge

A Method to Realize Multipoint Ignition with Microwave Plasma

Design and fabrication of energetic Al/Ni exploding foil with enhanced energy efficiency and plasma density for direct ignition