Abstract:Low-strength anastomoses and thermal damage of tissue are major concerns in laser tissue welding techniques where laser energy is used to induce thermal changes in the molecular structure of the tissues being joined, hence allowing them to bond together. Laser tissue soldering, on the other hand, is a bonding technique in which a protein solder is applied to the tissue surfaces to be joined, and laser energy is used to bond the solder to the tissue surfaces. The addition of protein solders to augment tissue repair procedures significantly reduces the problems of low strength and thermal damage associated with laser tissue welding techniques. Investigations were conducted to determine optimal solder and laser parameters for tissue repair in terms of tensile strength, temperature rise and damage and the microscopic nature of the bonds formed. An in vitro study was performed using an 808 nm diode laser in conjunction with indocyanine green (ICG)-doped albumin protein solders to repair bovine aorta specimens. Liquid and solid protein solders prepared from 25% and 60% bovine serum albumin (BSA), respectively, were compared. The efficacy of temperature feedback control in enhancing the soldering process was also investigated. Increasing the BSA concentration from 25% to 60% greatly increased the tensile strength of the repairs. A reduction in dye concentration from 2.5 mg ml(-1) to 0.25 mg ml(-1) was also found to result in an increase in tensile strength. Increasing the laser irradiance and thus surface temperature resulted in an increased severity of histological injury. Thermal denaturation of tissue collagen and necrosis of the intimal layer smooth muscle cells increased laterally and in depth with higher temperatures. The strongest repairs were produced with an irradiance of 6.4 W cm(-2) using a solid protein solder composed of 60% BSA and 0.25 mg ml(-1) ICG. Using this combination of laser and solder parameters, surface temperatures were observed to reach 85+/-5 degrees C with a maximum temperature difference through the 150 microm thick solder strips of about 15 degrees C. Histological examination of the repairs formed using these parameters showed negligible evidence of collateral thermal damage to the underlying tissue. Scanning electron microscopy suggested albumin intertwining within the tissue collagen matrix and subsequent fusion with the collagen as the mechanism for laser tissue soldering. The laser tissue soldering technique is shown to be an effective method for producing repairs with improved tensile strength and minimal collateral thermal damage over conventional laser tissue welding techniques.

Effect of Scanning Modes on the Tensile Strength and Stability in Laser Skin Welding in Vitro

Experimental study on the effect of scanning path on skin tissue properties of femtosecond laser welding

Study on mechanism underlying effect of scanning paths on healing performances in dual-beam laser welding

Optimization of Processing Parameters of Laser Skin Welding in Vitro Combining the Response Surface Methodology with NSGA- II

Effect of Laser Processing Parameters on Microstructural Characteristics of Skin <i>in vitro</i>

Investigation of collagen reconstruction mechanism in skin wound through dual-beam laser welding: Insights from multi-spectroscopy, molecular dynamics simulation, and finite element multiphysics simulation

Multivariate Nonlinear Regression Model Of Laser Fusion In Vitro Skin Tissue Incision Performance Based On Response Surface Methodology

Effects of Dyes on Tensile Strength and Thermal Damage of Laser Biological Tissue Soldering

Effect of Process Parameters on the Performance of Laser Repair of Esophageal Tissue Incisions

Multi-Objective Optimization for Laser Closure Process Parameters in Vitro Skin Tissue Based on NSGA-Ⅱ

Research on the Effect of Process Parameters on the Performance of Femtosecond Laser-Bonded Skin Microstructure

Experimental Study on the Process and Performance of Laser-Assisted Vascular Anastomosis Based on Response Surface Methodology

The effect of rescanning strategy on residual stress and deformation of laser-based powder bed fusion of 316L stainless steel thin-walled parts

Finite element simulation and experimental validation of thermal damage to isolated porcine skin tissue by femtosecond laser welding

Impact of SWCNTs and CMCS on efficacy of anastomosis and optical properties in vivo during laser biological tissue soldering

Laser tissue welding by using collagen excitation at a 1,720 nm near-infrared optical window III

Amendments of weld formation in human skin laser soldering

Reconstruction of Soft Biological Tissues Using Laser Soldering Technology with Temperature Control and Biopolymer Nanocomposites

Laser assisted vascular welding with real time temperature control

Unveiling the Cellular Microstructure–property Relations in Martensitic Stainless Steel Via Laser Powder Bed Fusion

Photothermal effects of laser tissue soldering