Importance of hypoxic cells to radiation treatment: further considerations.

H. Suit

1999-11-01

Abstract:

What problem does this paper attempt to address?

Effect of Process Parameters on the Performance of Laser Repair of Esophageal Tissue Incisions

Jun Huang,Jincheng Li,Mintao Yan,Yanyu Li,Kehong Wang

DOI: https://doi.org/10.1016/j.optlastec.2024.111204

IF: 4.939

2024-01-01

Optics & Laser Technology

Abstract:To study the influence of laser parameters on the mechanical properties and thermal damage of esophageal tissue, the experiment of laser repair of esophageal tissue incision is made. The effects of parameters including the laser power, scanning speed, defocusing amount, scanning path on the bursting pressure strength of esophageal tissue are analyzed. The influence of different energy densities on the appearance of esophageal tissue morphology, microstructure, and the degree of thermal denaturation of collagen is analyzed. The results showed that the laser power and the interaction factor of laser power x scanning path is the most important factor affecting the bursting pressure strength of esophageal tissues. The optimal parameters are laser power 6 W, scanning speed 150 mm/s, defocusing amount 0 mm, and scanning path 3, the highest bursting pressure strength of 93.3 mmHg is achieved. Meanwhile the esophageal tissues do not show obvious scarring, and the degree of thermal denaturation of tissue collagen is the smallest, which is only 1.6 x 10-5, the texture of the tissue microscopic images is uniformly changed, and the texture clarity is high.
Experimental Study on Anastomotic Hemodynamics Using Tomographic Particle Image Velocimetry

Ke-Wei Xu,Qi Gao,Min Wan,Ke Zhang

DOI: https://doi.org/10.55037/lxlaser.21st.105

2024-01-01

Abstract:Fluid mechanics is an important factor to the failure of the graft anastomosis surgery. In order to better understand the mechanism of restenosis and graft failure of the anastomosis from the perspective of fluid mechanics, an end-toside silicone anastomosis model with 45° anastomotic angle was used for research. The anastomosis model was connected to a continuous flow loop. where the flow rate can be adjusted during the experiment to simulate several conditions. The tomographic particle image velocimetry (TPIV) was applied to obtain the internal three-dimensional and three-component (3D-3C) flow field. The hemodynamics inside the anastomosis model was quantitatively analyzed based on the averaged 3D-3C flow field. The results present that there are phenomena such as recirculation, spiral flow, flow stagnation, and large vortex structures inside the anastomotic flow field. The oscillation of the recirculation zone size and flow stagnation point indicate the fluid stimulation to the endothelial cells. Also, the double spiral vortex structure could cause high local shear stress, which in turn cause trauma to the red blood cells and lead to local coagulation. Besides, thanks to the 3D-3C flow field, the wall shear stress (WSS) on the entire model wall was obtained, which enables us to predict the mechanical influence to the intimal hyperplasia. The local low WSS was found near the graft toe and recirculation regions, while the local high WSS was found on the host vessel bottom where the jet directly impinges. The abnormal flow phenomena can explain the high-risk regions in the anastomosis, where the stenosis and intimal hyperplasia are prone to appear. The 3D-3C flow field based on the in vitro experiment can strengthen the understanding of the anastomotic restenosis pathology and provide further reference for the surgery improvement.
Experimental Study on Hemodynamics of an End-to-side Anastomosis

Ke-Wei Xu,Xintao Lu,Qi Gao,Min Wan,Ke Zhang

DOI: https://doi.org/10.1063/5.0202774

IF: 4.6

2024-01-01

Physics of Fluids

Abstract:A three-dimensional and three-component velocity measurement on the flow field in a 45° end-to-side anastomosis model is conducted to investigate the hemodynamics, which is an important factor to the intimal hyperplasia formation and graft failure after surgery. Thanks to the advanced volumetric measurement technology of tomographic particle image velocimetry, the recirculation zone, low-speed region, and the spiral flow structures can be visualized. As a result, the flow field of three cases with the local maximum velocity of 0.15, 0.8, and 1.4 m/s are visible and the inlet velocity profile tends to be skewed as the flow rate increases. The mean vorticity contours indicate that the positive vortex center rotates 6.47°, 50.23°, and 90.4° and the negative vortex center rotates 20.44°, 15.73°, and 68.47°, respectively, in three cases. The instantaneous vortex structures identified by the λci criterion demonstrate two large-scale vortex structures in the distal section. The two vortices have the tendency to intertwine while one of them decays earlier. The wall shear stress (WSS) distributions on the entire model with the local maximum of 0.8, 5.8, and 13.8 Pa in three cases have been quantitatively achieved. The abnormal WSS and WSS gradient can help localize risk areas and understand the intimal hyperplasia formation. A detailed illustration of hemodynamics inside the 45° end-to-side anastomosis model has been provided, which demonstrates more comprehensive large-scale flow structures and abnormal WSS regions. Combined with the information of flow structures and WSS distribution, the understanding of the hemodynamics in the anastomosis can be strengthened.
Multivariate Nonlinear Regression Model Of Laser Fusion In Vitro Skin Tissue Incision Performance Based On Response Surface Methodology

Liu Qimeng,Huang Jun,Wang Kehong,Zhou Qi

DOI: https://doi.org/10.3788/CJL201845.0807002

2018-01-01

Chinese Journal of Lasers

Abstract:Based on the design method of response surface methodology, pulsed laser welding process experiment of in vitro skin tissue is performed to obtain the tensile strength and peak temperature data of tissue incision. On the basis of single factor experiment, the multivariate nonlinear mathematical regression model is established by using laser power, spot moving speed and laser frequency as the three influencing factors. Correlation coefficients of the regression model are obtained by analysis of variance and regression analysis as follows: correlation coefficient of incision tensile strength is 0. 9131, correlation coefficient of incision peak temperature is 0. 9985. The results of model analysis show that the main effect and interactions of laser power, spot movement speed and laser frequency have a great influence on the incision performance. The main effect that has the greatest influence on the tensile strength of incision is laser power, and the interaction effect is laser power and spot movement speed. The main effect that has the greatest influence on the peak incision temperature is laser power, and the interaction effects are laser power and spot movement speed, laser power and laser frequency, and spot movement speed and laser frequency. Finally, the optimal combination of laser process parameters is obtained based on the regression model. The experimental results show that the response values of regression model are consistent with the experimental results, and the incision strength meets the requirements.
Experimental Analysis of In Situ Fenestration of Endovascular Stent-Grafts: Comparison between Needle and Laser Puncture

Qinglong Zeng,Xiang Zhou,Yunjun He,Xiaohui Wang,Tao Shang,Yangyan He,Ziheng Wu,Hongkun Zhang,Donglin Li

DOI: https://doi.org/10.1016/j.avsg.2021.05.021

IF: 1.5

2021-01-01

Annals of Vascular Surgery

Abstract:Background: To evaluate the quality of in vitro fenestrations during in situ fenestration (ISF) and investigate the differences between needle and laser puncture in current stent-grafts. Methods: An in vitro study evaluated the damage created by needle ISF on stent-graft fabrics versus laser ISF. Fenestrations were made in 5 different commercially available stent-grafts, including polyester stent-grafts (Relay, Valiant and Hercules) and expanded polytetrafluoroethylene (ePTFE) stent-grafts (TAG and Ankura). Each stent-graft received fenestration by needle and laser separately, followed by gradual dilation (4 mm, 6 mm, 8 mm, and 10 mm sequentially) of noncompliant balloons. Quantitative and qualitative evaluations including fenestration diameter, area, shape and margins were conducted using light microscopy and scanning electron microscope. Results: The primary fenestrations created by needle were slit-like with visible cut-off fibers in polyester stent-grafts and were almost circular with clear margins in ePTFE stent-grafts; those created by laser were squared or elliptical with ragged edges and burned fibers in all the stentgrafts. Fabric debris and toxic particles due to burning of the material were generated during laser-assisted fenestration. The Primary holes in polyester stent-grafts (Relay, Valiant and Hercules) by needle showed smaller area (0.05 mm(2) vs. 0.22 mm(2), 0.52 mm(2) vs. 0.70 mm(2) and 0.28 mm(2) vs. 0.46 mm(2); P < 0.01) and worse shape (0.93 vs. 2.46, 1.17 vs. 2.33 and 0.93 vs. 2.47; P < 0.01) than those by laser, while larger area (0.67 vs.0.43, 0.59 vs.0.45; P < 0.05), better shape (3.93 vs. 2.53, 3.90 vs. 2.93; P < 0.05) and better margin (3.83 vs. 2.47, 3.83 vs. 2.53; P < 0.05) in ePTFE stent-grafts (TAG and Ankrura). After gradual balloon dilation, the final holes showed no evident difference in maximal length, fenestration area, scores of shape and margin between the 2 ways of fenestration (P > 0.05). Ankura stent-graft showed the largest holes with best quality than the others. Conclusions: The primary fenestrations were different between needle and laser puncture, laser induced fabric debris and toxic particles release should be cautiously considered. The final fenestrations were similar after gradual balloon dilation.
Optimization of Processing Parameters of Laser Skin Welding in Vitro Combining the Response Surface Methodology with NSGA- II

Cong Li,Jun Huang,Kehong Wang,Zibo Chen,Qimeng Liu

DOI: https://doi.org/10.1016/j.infrared.2019.103067

IF: 2.997

2019-01-01

Infrared Physics & Technology

Abstract:Objective: This study aimed to optimize the parameters of laser skin welding by combining the response surface methodology with NSGA-II, so as to achieve the goal of improving the weld strength while causing as little thermal damage as possible. Methods: The response surface methodology was used to design the experiment. The optimization model of laser biological tissue welding process parameters was established, which took the power, pulse frequency and scanning speed of the laser as the optimization variables, the maximum tensile strength of the incision and the peak temperature of skin tissue as the optimization objectives. Meanwhile, the multi-objective NSGA-II algorithm was used to find the optimal solution and obtain the optimal process parameters. Then we carried out experiments to verify the effect of the optimized parameters by comparing with the unoptimized result. Results: The optimized process parameters of laser skin welding were effective to improve the welding quality and achieve full-thickness penetration of the skin tissue. Compared with the non-optimized groups, on the premise of guaranteeing maximum strength, the peak temperature of tissue is reduced. Conclusions: Using the optimized process parameters to weld the skin tissues can obtain higher welding strength and at the same time cause low levels of thermal damage. This also verifies the correctness of the model, which is helpful to improve the adaptability of laser welding to other different tissues and reduce the consumption of time and material.
Laser assisted vascular welding with real time temperature control

R B Stewart,A Benbrahim,G M LaMuraglia,M Rosenberg,G J L'Italien,W M Abbott,R T Kung

DOI: https://doi.org/10.1002/(SICI)1096-9101(1996)19:1<9::AID-LSM2>3.0.CO;2-W

Abstract:Background and objective: Previous studies in laser assisted vascular welding have been limited by the lack of a reliable end point for tissue fusion. As a means of improving the reproductibility of laser assisted repairs, a system incorporating real time temperature monitoring and closed loop feedback was used. Study design/materials and methods: The system consisted of a direct view infrared thermometer for monitoring the laser heated spot, a 1.9 microns diode laser, and a microprocessor for data acquisition and feedback control of the laser power to maintain a constant tissue temperature. Rat aortas were welded under constant surface temperature conditions. Results: In vivo temperature stability of +/- 2 degrees C was achieved over a temperature range of 70-90 degrees C pertinent to welding small vessels. When welds were completed using the feedback system to maintain the tissue temperature at 80 degrees C, the acute success rate was 100% and the burst pressure was 290 +/- 70 mmHg. Conclusion: These studies demonstrate that the use of real time monitoring and feedback control results in improved consistency for vascular tissue welding.
Multi-Objective Optimization for Laser Closure Process Parameters in Vitro Skin Tissue Based on NSGA-Ⅱ

Liu Qimeng

DOI: https://doi.org/10.3788/cjl201946.0207001

2019-01-01

Chinese Journal of Lasers

Abstract:By selecting laser power, laser pulse frequency and scanning speed as optimization variables, we establish a multi-objective optimization model of laser closure process parameters in vitro skin tissue. Based on MATLAB software, we use second generation non-dominant sequencing genetic algorithm ( NSGA-II) to find the Parcto optimal solution set, obtain the optimal process parameters, and then analyze the response sensitivity of optimization objectives to the variation of process parameters. Under the optimized process parameters, the tensile strength of the incision is tested and the microstructure is analyzed. The results show that the incision tensile strength has high sensitivity to the laser process parameters, and the laser power has significant effect on the incision tensile strength and the tissue peak temperature. The proposed optimized process can achieve the in vitro skin tissue closure in full-thickness. In the case of tissue peak temperature decreasing, the tensile strength of in vitro skin tissue incision is 5.6% higher than that of single-objective optimization.
Multi-objective Numerical Simulation of Geometrical Characteristics of Laser Cladding of Cobalt-Based Alloy Based on Response Surface Methodology

Lu-jun Cui,Meng Zhang,Shi-Rui Guo,Yan-Long Cao,Wen-Han Zeng,Xiao-lei Li,Bo Zheng

DOI: https://doi.org/10.1177/0020294020944955

2020-01-01

Measurement and Control

Abstract:The objectives of this study are to optimize the key process parameters of laser cladding remanufacturing parts, improve the sealing quality of the hemispherical valve and prolong and improve its service life and reliability. A high-power fiber-coupled semiconductor laser was used to fabricate a single Co-based alloy cladding layer on the pump valve material ZG45 plate. The key process parameters of laser power, scanning speed and powder feeding rate in the process of laser remanufacturing are taken as optimization variables, and the coating width, coating height, coating depth, aspect ratio and dilution rate are taken as response indexes. Based on the response surface analysis method, the central compound experiment is designed using Design-Expert software. The variance analysis of the experimental results is performed, and the regression prediction model of the process parameters relative to the corresponding index is established. Through analysis of the established perturbation diagram and three-dimensional response surface, it is concluded that the main influence factors of melting width and penetration depth are laser power and positive effect, and the main influence factors of melting height are scanning speed and negative effect. The average error of each regression prediction model is lower than 10%. The above research work has important guiding significance for optimizing the process parameters and improving the cladding quality of cobalt-based alloy on ZG45.
Effect of Scanning Modes on the Tensile Strength and Stability in Laser Skin Welding in Vitro

Cong Li,Kehong Wang,Jun Huang

DOI: https://doi.org/10.1016/j.ijleo.2018.10.037

IF: 3.1

2019-01-01

Optik

Abstract:In order to obtain the effect of laser scanning mode on the fusion result in vitro biological tissue, the experiment was designed to explore the effect of laser scanning mode on the fusion morphology, tensile strength and stability of skin incision. The results showed that the use of segmented scanning welding method can significantly improve the incision's effective absorption of the laser energy and the stability of welding quality is higher. On this basis, the reliability test was carried out with the optimized process parameters, and the tensile strength of the incision was tested. The results showed that under the condition of the process, the incision can achieve full layer fusion and no defects such as burning and carbonization. Compared with the continuous scanning laser welding process, the welding time can be reduced by 30-40%. The tensile strength of the incision after welding is up to 0.38 MPa, to meet the strength requirements. The adaptability is strong and the quality is stable.
Relevant parameters for laser surgery of soft tissue

Martin Hohmann,David Kühn,Dongqin Ni,Moritz Späth,Anindya Ghosh,Maximilian Rohde,Florian Stelzle,Florian Klämpfl,Michael Schmidt

DOI: https://doi.org/10.1038/s41598-024-51449-1

IF: 4.6

2024-01-14

Scientific Reports

Abstract:In recent years, the laser has become an important tool in hospitals. Laser surgery in particular has many advantages. However, there is still a lack of the understanding of the influence of the relevant parameters for laser surgery. In order to fill this gap, the parameters pulse frequency, use of an exhaustion system, air cooling, laser power, laser scan speed, laser line energy and waiting time between cuts were analysed by ANOVA using inter-animal variation as a benchmark. The quality of the cuts was quantized by a previously published scoring system. A total of 1710 cuts were performed with a laser. Of the parameters investigated, laser power and scan speed have the strongest influence. Only the right combination of these two parameters allows good results. Other effects, such as the use of pulsed or continuous wave (CW) laser operation, or air cooling, show a small or negligible influence. By modulating only the laser power and scan speed, an almost perfect cut can be achieved with a laser, regardless of the external cooling used or the laser pulse duration or repetition rate from CW to nanosecond pulses.

multidisciplinary sciences
Study on mechanism underlying effect of scanning paths on healing performances in dual-beam laser welding

Yuxin Chen,Kehong Wang,Jun Huang,Xiaopeng Li,Yunfeng Rui

DOI: https://doi.org/10.1016/j.optlastec.2024.112074

IF: 4.939

2024-11-10

Optics & Laser Technology

Abstract:A dual-beam laser system was developed for closing skin wounds and investigated the healing performance of these wounds after welding using five different laser scanning paths with increasing sparsity. The five paths included Peano, Circle, Jagged, Airwave, and Surgical suture needle point paths. These paths exhibited symmetrical structures along the incision, with decreasing sparsity in the aforementioned order. Total Energy density is 102.96 J/cm 2 with the interspace between beams is 0.1865 mm. Soldering time is 300 s and effective fusion area is 0.2625 mm 2 . Macroscopic morphology and biomechanical strength of skin samples under different laser scanning paths were evaluated using metallographic microscopy and high-precision electronic push–pull force gauge measurements. HE staining was employed to characterize the influence of laser scanning paths on microscopic tissue structure of samples, while Masson staining represented the degree of collagen damage under different scanning paths. Fluorescence spectroscopy was used to analyze energy transfer between tyrosine and phenylalanine, Fourier transform near-infrared spectroscopy demonstrated collagen molecular structural changes, and Raman spectroscopy further analyzed peptide chain folding mechanisms. Finally, Sirius Red staining was utilized to analyze fibrosis tendency in wound healing by examining distribution and content of type I and III collagens after welding with different laser scanning paths. The final results showed that dual-beam laser welding of skin incisions under Jagged path conditions can achieve stable biomechanical strength, fine microstructural texture, and full-thickness fusion. The functionality of tyrosine remains unaffected by laser energy damage, primarily due to the reconstruction of acylamide III band accompanied by the formation of new peptide chains. The ratio between collagen I and collagen III in welded area is close to 0.6, with a rich presence of type III collagen around the denatured region of collagen, contributing in high elasticity and reduced tendency for scar formation during later stages of healing process.

optics,physics, applied
Research on the Effect of Process Parameters on the Performance of Femtosecond Laser-Bonded Skin Microstructure

Jun Huang,Mengshi Jia,Shengnan Xia,Yuxin Chen,Xiaopeng Li,Kehong Wang,Yunfeng Rui

DOI: https://doi.org/10.1002/jbio.202300157

IF: 3.3899

2023-01-01

Journal of Biophotonics

Abstract:In this paper, the effect of the femtosecond laser process parameters on the texture characteristics of the microstructure was analyzed with the response surface method. The correspondence between the temperature of skin during laser bonding and microscopic tissue texture characteristics parameters was explored. The results show that the three process parameters of laser power, scanning speed, and scanning times and the interaction between the parameters have different patterns of influence on the four texture characteristics parameters of skin microstructure angular second-order moments, entropy, contrast, and relevance. Angular second-order moments and relevance of skin microstructure textures increase with increasing temperature, while entropy values and contrast decrease. It provides another way to evaluate the performance of femtosecond laser-bonded skin with microstructure.
The effects of immobilization, after lower leg fracture, on the contractile properties of human triceps surae.

M. White,C. Davies

DOI: https://doi.org/10.1042/CS0660277

1984-03-01

Clinical Science

Abstract:The contractile properties of the triceps surae were evaluated in 11 patients after unilateral fracture of the lower leg and subsequent immobilization for 135 +/- 68 days. Calf muscle cross-sectional area (plus bone: CSA) was assessed from anthropometric measurement. It was shown that the injured leg had a faster time to peak tension and increased half-relaxation time (1/2 RT); twitch force (Pt) was reduced by 25%. Evoked maximal tetanic tensions (Po) at 10 and 20 Hz were reduced by 51% and 46% respectively compared with the uninjured leg. The force of a maximal voluntary contraction (MVC) was also reduced, by 50%, but calf circumference and CSA were only 5% and 16% respectively lower in the injured leg. It was concluded that the changes in contractile speed may indicate a relatively greater atrophy of slow (type I) muscle fibres. The relationship between CSA and tension generation in the injured limb was shown to be poor after immobilization and during recovery. Anthropometric estimation of CSA does not appear to reflect the degree of muscle wasting, as indicated by reduced tension development after immobilization.
Investigation on the modeling and simulation of hydrodynamics in asymmetric conduction laser micro-welding of austenitic stainless steel and its process optimization

José Luis Velázquez de la Hoz,Kai Cheng

DOI: https://doi.org/10.1177/09544054241235839

2024-03-20

Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture

Abstract:Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Ahead of Print. Laser micro-welding is a joining technology utilized across various high-value industries, like medical, automotive, e-mobility, and aerospace. A trial-and-error process to identify welding parameters does not necessarily lead to optimized quality levels. Furthermore, offline non-destructive examination methods often launched to verify welding quality may inadvertently trigger excessive costs and time delays, ultimately failing to guarantee defect-free welds. In response to these challenges, this article introduces an advanced multiscale model designed to unravel the intricate dynamics of hydrodynamics and the overarching physics within laser micro-welding melting pools. Developed using the COMSOL software package, the model adeptly demonstrates how surface tension gradients shape the geometry of welds, thus influencing their quality. This knowledge allows the mapping of welding defects. One of the novelties of the article is to introduce geometric dissimilar welding conditions by simulating an asymmetric edge joint. It shows a study on a new, unstudied way to laser weld with many applications in the field. The model further establishes its utility in design experiments to determine parameter, tolerance, and system design. Moreover, the insights garnered from understanding and controlling these drivers have far-reaching implications for the advancement of subsequent methodological research and the development of in-situ quality control practices by characterizing the welding defects. Finally, the results shows that the discouragingly high computational costs restrict its potential application to support a Digital Twin.

engineering, mechanical, manufacturing
An Ex Vivo Preliminary Investigation into the Impact of Parameters on Tissue Welding Strength in Small Intestine Mucosa-Mucosa End-to-end Anastomosis.

Caihui Zhu,Li Yin,Jianzhi Xu,Haotian Liu,Xiaowei Xiang,Hui Zhao,Jian Qiu,Kefu Liu

DOI: https://doi.org/10.3389/fbioe.2023.1200239

IF: 5.7

2023-01-01

Frontiers in Bioengineering and Biotechnology

Abstract:Background: Tissue welding is an electrosurgical technique that can fuse tissue for small intestine anastomosis. However, limited knowledge exists on its application in mucosa-mucosa end-to-end anastomosis. This study investigates the effects of initial compression pressure, out-put power, and duration time on anastomosis strength ex vivo in mucosa-mucosa end-to-end anastomosis.Methods: Ex vivo porcine bowel segments were used to create 140 mucosa-mucosa end-to-end fusions. Different experimental parameters were employed for fusion, including initial com-pression pressure (50kPa-400 kPa), output power (90W, 110W, and 140W), and fusion time (5, 10, 15, 20 s). The fusion quality was measured by burst pressure and optical microscopes.Results: The best fusion quality was achieved with an initial compressive pressure between 200 and 250 kPa, an output power of 140W, and a fusion time of 15 s. However, an increase in output power and duration time resulted in a wider range of thermal damage. There was no significant difference between the burst pressure at 15 and 20 s (p > 0.05). However, a substantial increase in thermal damage was observed with longer fusion times of 15 and 20 s (p < 0.05).Conclusion: The best fusion quality for mucosa-mucosa end-to-end anastomosis ex vivo is achieved when the initial compressive pressure is between 200 and 250 kPa, the output power is approximately 140W, and the fusion time is approximately 15 s. These findings can serve as a valuable theoretical foundation and technical guidance for conducting animal experiments in vivo and subsequent tissue regeneration.
Effect of optical temperature feedback control on patency in laser-soldered microvascular anastomosis

D Pohl,L S Bass,R Stewart,D T Chiu

DOI: https://doi.org/10.1055/s-2007-1006897

Abstract:Feedback control has been postulated to improve the efficacy of laser welding in microsurgery, but alteration of outcome has not been clearly shown. The authors evaluated the ability of an optical closed loop temperature feedback control to improve patency, aneurysm rate, and to histologically limit thermal damage. Rat femoral artery anastomoses were performed under operating microscope magnification. One hundred and twenty-four anastomoses were performed in five groups using 1) free-hand (FH) 1.9-microm laser soldering without feedback; 2) temperature controlled (TC) 1.9-microm laser soldering with optical feedback; 3) FH 808 nm laser; 4) TC 808 nm laser soldering; and 5) 10-0 nylon suture control. In Groups 2 and 4, an optical feedback system controlling laser exposure to produce a preset temperature was used. Anastomotic time was significantly less for all laser groups (p < 0.05). Late patency for all 1.9-microm laser anastomoses was almost 0. Temperature controlled 808-nm anastomoses showed no significant difference from sutures in terms of patency (88 percent vs. 96 percent), bursting pressure, and aneurysm rate, while freehand 808-nm anastomoses had a significantly lower patency (71 percent) and more tissue damage (ANOVA, p < 0.05). The authors conclude that temperature control improves outcome in microvascular anastomosis by reducing transmural thermal injury caused by variations in surgeon technique.
Effect of Laser Processing Parameters on Microstructural Characteristics of Skin <i>in vitro</i>

Chen Zibo,Huang Jun,Wang Kehong,Chen Yuxin,Yan Long

DOI: https://doi.org/10.3788/CJL202047.0302001

2020-01-01

Chinese Journal of Lasers

Abstract:This paper introduced the texture feature analysis method in digital image processing technology into laser biological tissue welding, and the microstructural changes of laser-welded skin in vitro were deeply analyzed. The second-order statistical features calculated using gray co-occurrence matrix were used as primary quantitative indexes to characterize the microstructural characteristics of isolated skin. The effects of laser parameters and their interaction on the microstructural and texture characteristics of laser-welded skin in vitro were obtained using a response surface method. The results show that the laser scanning speed is the key factor that affects the microstructure of isolated skin subsequent to welding, and the angular second moment, correlation, entropy, and contrast have significant effects on the texture feature parameters. Furthermore, the laser power and the interaction between laser power and welding speed have significant effects on the angular second moment, correlation, and entropy.
Study on Effect of Laser Process Parameters on Laser Transmission Weld Parameters using ANSYS

Girish Kumar R,Abhay Agarwal,Utkarsha Mohan,Shounak Dey,,,,

DOI: https://doi.org/10.51201/jusst/21/07264

2021-07-21

Journal of University of Shanghai for Science and Technology

Abstract:In recent years, a mode of welding that has garnered a considerable amount of interest is the laser transmission welding of thermoplastics. Laser transmission welding is now being used as an alternative to adhesives to join two thermoplastics. In this study, a finite element model has been developed to simulate the laser transmission welding of polypropylene. The movement of the laser beam was done using a Moving Heat Source in Ansys®. Process parameters namely laser power, welding speed, and the number of passes have been studied in order to investigate their effects on the temperatures and the weld widths achieved during welding. It was found that an increase in the laser power had a positive effect on the maximum temperature at the weld interface as well as the weld width. Similarly, an increase in the welding speed had a negative influence on the maximum temperature at the weld interface as well as the weld width.
Assessing the Influence of Parameters on Tissue Welding in Small Bowel End-to-end Anastomosis in Vitro and in Vivo

Caihui Zhu,Yuyan Na,Xiujun Cheng,Xiaonan Tao,Pengyao Xie,Lei Chen,Hui Zhao,Jian Qiu,Xiaodong Gu,Jianbin Xiang,Kefu Liu

DOI: https://doi.org/10.1007/s00464-024-10795-x

2024-01-01

Abstract:The use of high-frequency electric welding technology for intestinal end-to-end anastomosis holds significant promise. Past studies have focused on in vitro, and the safety and efficacy of this technology is uncertain, severely limiting the clinical application of this technology. This study investigates the impact of compression pressure, energy dosage, and duration on anastomotic quality using a homemade anastomosis device in both in vitro and in vivo settings. Two hundred eighty intestines and 5 experimental pigs were used for in vitro and in vivo experiments, respectively. The in vitro experiments were conducted to study the effects of initial pressure (50–400 kpa), voltage (40–60 V), and time (10–20 s) on burst pressure, breaking strength, thermal damage, and histopathological microstructure of the anastomosis. Optimal parameters were then inlaid into a homemade anastomosis and used for in vivo experiments to study the postoperative porcine survival rate and the pathological structure of the tissues at the anastomosis and the characteristics of the collagen fibers. The anastomotic strength was highest when the compression pressure was 250 kPa, the voltage was 60 V, and the time was 15 s. The degree of thermal damage to the surrounding tissues was the lowest. The experimental pigs had no adverse reactions after the operation, and the survival rate was 100

Importance of hypoxic cells to radiation treatment: further considerations.

Effect of Process Parameters on the Performance of Laser Repair of Esophageal Tissue Incisions

Experimental Study on Anastomotic Hemodynamics Using Tomographic Particle Image Velocimetry

Experimental Study on Hemodynamics of an End-to-side Anastomosis

Multivariate Nonlinear Regression Model Of Laser Fusion In Vitro Skin Tissue Incision Performance Based On Response Surface Methodology

Experimental Analysis of In Situ Fenestration of Endovascular Stent-Grafts: Comparison between Needle and Laser Puncture

Optimization of Processing Parameters of Laser Skin Welding in Vitro Combining the Response Surface Methodology with NSGA- II

Laser assisted vascular welding with real time temperature control

Multi-Objective Optimization for Laser Closure Process Parameters in Vitro Skin Tissue Based on NSGA-Ⅱ

Multi-objective Numerical Simulation of Geometrical Characteristics of Laser Cladding of Cobalt-Based Alloy Based on Response Surface Methodology

Effect of Scanning Modes on the Tensile Strength and Stability in Laser Skin Welding in Vitro

Relevant parameters for laser surgery of soft tissue

Study on mechanism underlying effect of scanning paths on healing performances in dual-beam laser welding

Research on the Effect of Process Parameters on the Performance of Femtosecond Laser-Bonded Skin Microstructure

The effects of immobilization, after lower leg fracture, on the contractile properties of human triceps surae.

Investigation on the modeling and simulation of hydrodynamics in asymmetric conduction laser micro-welding of austenitic stainless steel and its process optimization

An Ex Vivo Preliminary Investigation into the Impact of Parameters on Tissue Welding Strength in Small Intestine Mucosa-Mucosa End-to-end Anastomosis.

Effect of optical temperature feedback control on patency in laser-soldered microvascular anastomosis

Effect of Laser Processing Parameters on Microstructural Characteristics of Skin <i>in vitro</i>

Study on Effect of Laser Process Parameters on Laser Transmission Weld Parameters using ANSYS

Assessing the Influence of Parameters on Tissue Welding in Small Bowel End-to-end Anastomosis in Vitro and in Vivo