Abstract:Objective Since the development of Yb-doped fiber laser, increasing the output of a single fiber has been one of the most important directions. The output of a single fiber has now been able to attain 10 kW-level or above. However, these results are mainly laboratory reports, and few fibers have been adopted in practical applications because the coating material of these double cladding fibers age quickly due to the injected high pump power and large amount of quantum defect heating. To minimize the impact of high pump power on coating materials, triple-clad Yb-doped fibers, with an addition of fluorine -doped fused silica between silica and low -index coating, have been suggested. For a given fiber, high brightness of the tandem-pumping can not only reduce the quantum defect heating, but also further increase the pump injection and output-power scaling. To achieve a more reliable and higher laser output, a highly Yb-doped triple-clad fiber used for tandem-pumping is proposed. ions The Yb-doped fiber preform has been prepared by modified chemical vapor deposition ( MCVD) in combination with sol-gel solution-doping method to improve the Yb-doped concentration without clusters. The doped preform was overcladded and shaped via grinding in an octagonal shape to form the pump cladding. The preform was further surrounded by the second highly fluorine -doped synthetic fused silica cladding with a depressed refractive index to form the out cladding. Then, the preform was drawn and coated as conventional double cladding fiber to obtain the triple -clad fiber ( Fig. 1). The fiber was characterized by refractive index profiling, electron probe microanalysis (EPMA), loss, and absorption. Finally, the fiber laser performance was characterized. Results and Discussions The fiber is 50/350/400 tan core-clad diameter, 0.06/0.22/0.46 NA, and approximately O. 6 dB/m inner cladding absorption at 1018 nm. The EPMA results showed that the homemade triple -clad fiber has a much higher Yb-doped concentration than the commonly used 20/400 ttm double cladding fiber (Fig. 2). The reduced core numerical aperture was achieved by higher fluorine -doped silica, and laser performance of the fiber was demonstrated by an all -fiber master oscillator power amplifier at 1080 nm. Figure 3 shows the experimental setup; the seed laser is about 600 W, generated via a 20/400 ttm Yb fiber laser oscillator. The triple-clad fiber was used as a gain medium in the power amplifying stage, and the pump sources are 1018 nm fiber lasers. When about 11606 W pump power was absorbed, up to 9010 W laser output with a slope efficiency of 80. 5% was achieved (Fig. 4). Further power scaling was limited by the unabsorbed helical light in the fluorine-doped fused silica cladding, which is round-shaped. Thus, in the high-power laser experiment, only the forward pump was on. In future studies, we will improve the design of fiber laser setup and reduce the pump power in the fluorine-doped silica to further increase the fiber laser output. Conclusions A maximum 9010 W laser output was achieved by the 1018 nm tandem-pumping using the homemade 50/350/400 tan large-mode-area Yb-doped triple-clad fiber. This is an important progress in the field of high-power fiber laser materials. Compared with double cladding fiber, the triple -clad fiber design, which deliveries most of the pump light inside the fluorine -doped fused silica, can greatly minimize the aging effect of the pump light on the coating material. This is of great significance for the long-term operation reliability of high-power laser fiber.

3 Kw 20/400 Yb-Doped Aluminophosphosilicate Fiber with High Stability

Yb-Doped Aluminophosphosilicate Laser Fiber

66 fs, 3 W all fiber Yb3+-doped mode-locked fiber laser

Yb-doped large-mode-area laser fiber fabricated by halide-gas-phase-doping technique

Yb-Doped Triple -Clad Fiber for Nearly 10 Kw Level Tandem-Pumped Output

Yb/Ce Codoped Aluminosilicate Fiber With High Laser Stability for Multi-kW Level Laser

Spectroscopic and Laser Properties of Al-P Co-Doped Yb Silica Fiber Core-Glass Rod and Large Mode Area Fiber Prepared by Sol-Gel Method

Double-clad large-mode-area polarization-maintaining ytterbium doped photonic crystal fiber

Growth and Characterization of Yb:Ho:YAG Single Crystal Fiber

Novel constant-cladding tapered-core ytterbium-doped fiber for high-power fiber laser oscillator

Single-mode large-mode-area laser fiber with ultralow numerical aperture and high beam quality

1010 nm Directly LD-Pumped 6kW Monolithic Fiber Laser Employing Long-Tapered Yb3+-Doped Fiber

Yb 3+ -Doped 200 Μm Diameter Core, Gain Guided Index-Antiguided Fiber

All-fiber 30-μm core diameter Yb-doped pulse-pumped amplifier cascade generating 10 nm-bandwidth 545 kW peak power pulses

A 5 kW Nearly-Single-Mode Monolithic Fiber Laser Emitting at ~1050 nm Employing Asymmetric Bi-Tapered Ytterbium-Doped Fiber

Linearly-polarized single-transverse-mode high-energy multi-ten nanosecond fiber amplifier with 50W average power.

High-efficiency cladding-pumped Er/Yb co-doped alumino-phosphosilicate fiber for an extended L-band amplification

High ytterbium concentration Yb/Al/P/Ce co-doped silica fiber for 1-μm ultra-short cavity fiber laser application

Fabrication and properties of domestic long tapered ytterbium-doped fiber with high tapering ratio

Fabrication and Characterization of Er~(3+):Yb~(3+) Co-doped Phosphosilicate Fibers

Properties of Ytterbium-Doped Double Clad Fiber Made in China