Abstract:So far, intrinsic hydrogenated amorphous silicon (a-Si:H(i)) has been commonly used below molybdenum oxide (MoOx) to form a good contact. An a-Si:H(i)/MoOx stack gives good surface passivation, but often results in poor carrier selectivity after exposure to slightly elevated temperatures >130 °C (Geissbühler et al., 2015) [1]. For this reason, we have investigated an alternative interface layer, a very thin Al2O3 tunneling layer (<2 nm), deposited by atomic layer deposition (ALD), that can provide surface passivation, higher transparency and thermal stability without affecting the hole transport across the contact. To demonstrate this new passivating contact a 6" moly-poly cell, with an Al2O3/MoOx stack at the front side and n-type doped polysilicon at the rear side, was made using a high- throughput spatial ALD tool, and E-beam PVD, for the Al2O3 and MoOx layers, respectively. This resulted in an efficiency of 18.2% with a Voc of 651 mV, a FF of 75.6% and a Jsc of 36.9 mA/cm2. A post-deposition anneal (PDA) of the thin Al2O3 interlayer has significant effect on the Al2O3 thickness, layer stoichiometry, contact selectivity, and sputtering-induced damage. Annealing at higher TPDA (350–600 °C) results in ineffective hole carrier transport and makes the stack more sensitive to ITO damage. The best performing device was, therefore, made using an Al2O3 layer without a PDA treatment. Moreover, we have found that this solar cell structure is thermally stable up to at least 210 °C, and even slightly improves under annealing which makes this device industrially appealing.

Low-resistance Orthorhombic MoO3-x Thin Film Derived by Two-Step Annealing

Role of thermal heat-treatment to achieve a highly polycrystalline and compact α-MoO3 thin films

The Effect of Thermal Annealing of Mo Film on the CuInSe2 Layer Texture and Device Performance

High UV Transparent Conductivity of SrMoO3 Thin Films

Conductive single-phase SrMoO3 epitaxial films synthesized in pure Ar ambience via plasma-assisted radio frequency sputtering

Novel transparent conductive films In2O3:Mo

Atomic layer deposition of crystalline molybdenum oxide thin films and phase control by post-deposition annealing

A new transparent conductive thin film In2O3:Mo

Constructing Conductive MoOx Thin Films by Plasma Enhanced Atomic Layer Deposition

Laminated indium-oxide/molybdenum-oxide nanocomposites for high-work-function electrodes in organic photovoltaics and capacitor devices

Wafer-Scalable Single-Layer Amorphous Molybdenum Trioxide

Facile preparation of anodized MoO3−x films and their boosted photocatalytic activity

Solution-processed molybdenum oxide films by low-temperature annealing for improved silicon surface passivation

Enhanced Electrical Properties of AZO/IZO Multilayered Thin Film with Post Laser Annealing Process

Large-area polycrystalline $α$-MoO3 thin films for IR photonics

Thermally stable MoOx hole selective contact with Al2O3 interlayer for industrial size silicon solar cells

Low-resistivity Oxides in TixFeCoNi Thin Films after Vacuum Annealing

Thermal Annealing Effects of V2O5 Thin Film as an Ionic Storage Layer for Electrochromic Application

Annealing-Insensitive, Alcohol-Processed MoO x Hole Transport Layer for Universally Enabling High-Performance Conventional and Inverted Organic Solar Cells

Sputter-grown two-dimensional α-MoO 3 thin films: Microstructure dependence on growth conditions

Transparent conductive In2O3:Mo thin films prepared by reactive direct current magnetron sputtering at room temperature