Abstract:Monolithic nanoporous copper (NPC) ribbons with unimodal or bimodal channel size distributions can be fabricated through chemical dealloying of Mg-Cu alloys with Cu content below 33 at.% in an acidic solution at room temperature. The microstructure of these NPC ribbons was characterized using X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, transmission electron microscopy, and high-resolution transmission electron microscopy. The experimental results show that with increasing Cu content from 13.5 at.% up to 32 at.%, NPC with unimodal channel size distributions gradually changes into that with bimodal channel size distributions upon the dealloying; meanwhile we found cracking to be unavoidable. For the Mg-Cu alloys composed of alpha-Mg and Mg2Cu, the microstructure of the NPC ribbons strongly depends upon phase proportions and distributions in the initial alloys. The Mg-Cu alloys with 13.5-25 at.% Cu can be fully dealloyed and result in the formation of NPC with a homogenous structure, while the separate dealloying of alpha-Mg and Mg2Cu in the Mg-32 Cu alloy leads to the formation of NPC with bimodal pore size distributions. Moreover, the microstructures of two distinct surfaces of the NPC ribbon from the Mg-32 Cu alloy make an essential difference due to the great disparity in the phase distributions, which can be attributed to the different cooling rates on the free and quenching surfaces during rapid solidification. In addition, the evolution process of porous structure along the thickness direction of alloy ribbons during the dealloying is from the interior to exterior, which is just contrary to the coarsening process during the post-dealloying. The evolution and coarsening mechanisms are discussed in detail based upon percolation theory and chloride ion effect.

The Mechanical Characteristics of Monolithic Nanoporous Copper and Its Composites

Formation and characterization of Monolithic nanoporous copper by chemical dealloying of Al-Cu alloys

Nanoporous Copper Fabricated by Dealloying Mn–Cu Precursors with Minor Nickel Element Addition and Heat Treatment Coarsening

Formation of Monolithic Nanoporous Copper with Ultrahigh Specific Surface Area Through Chemical Dealloying of Mg-Cu Alloy

Microstructures and mechanical properties of bulk nanoporous copper fabricated by dealloying Al-Cu alloys

Influence of Alloy Composition on Nanoporous Structure by Dealloying Mn-Cu Ribbons

Nanoporous Copper Films with High Surface Area Formed by Chemical Dealloying from Electroplated CuZn Alloy

Controllable Nanoporous Copper Synthesized by Dealloying Metallic Glasses: New Insights into the Tuning Pore Structure and Applications

Influence of Dealloying Solution on the Microstructure of Monolithic Nanoporous Copper Through Chemical Dealloying of Al 30 At.% Cu Alloy

Fabrication and Characterization of Magnetic Nanoporous Cu/(Fe,Cu)3O4 Composites with Excellent Electrical Conductivity by One-Step Dealloying

Hierarchical Nanoporous Metal/bmg Composite Rods with Excellent Mechanical Properties

Influence of Phase Constituent and Proportion in Initial Al–Cu Alloys on Formation of Monolithic Nanoporous Copper Through Chemical Dealloying in an Alkaline Solution

Monolithic Nanoporous Copper Ribbons from Mg-Cu Alloys with Copper Contents below 33 At.%: Fabrication, Structure Evolution and Coarsening Behavior along the Thickness Direction

Fabrication and Compression Properties of Bulk Hierarchical Nanoporous Copper with Fine Ligament

Nanostructural features in nanoporous copper coatings fabricated by laser deposition

Effects of Initial Alloy Organization on Formation and Morphology of NPC

Fabrication and Degradation Properties of Nanoporous Copper with Tunable Pores by Dealloying Amorphous Ti-Cu Alloys with Minor Co Addition

Structure Evolution of Nanoporous Copper by Dealloying of Al 17-33 At% Cu Alloy

A Facile One-Pot Route to Fabricate Nanoporous Copper with Controlled Hierarchical Pore Size Distributions Through Chemical Dealloying of Al–Cu Alloy in an Alkaline Solution

Fabrication and Dealloying Behavior of Monolithic Nanoporous Copper Ribbons with Bimodal Channel Size Distributions

Preparation and performances of nanoporous copper for low temperature bonding