Abstract:Through defect modulation, ZrB 2 powder was controllably synthesized using the carbon thermal reduction (CTR) method, with boron powder serving as a novel additive. Thermodynamic data for the ZrO 2 -B 2 O 3 -C system in the presence of boron were calculated using HSC thermodynamic software. Additionally, TG-DSC thermal analysis combined with XRD was used to investigate the reaction process. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) were used to analyze the defect structure and grain surface characteristics of the reaction products. The results indicate that the reaction of B with ZrO 2 and C exothermically alters the nucleation environment of ZrB 2 grains. The helical dislocations generated act as a source of crystal growth steps, promoting the growth of smooth interfaces and leading to a transformation of the ZrB 2 grain growth mechanism. Quantitative calculations of the dislocation density of ZrB 2 powders, using the convolutional multiple whole profile fitting (CMWP-fit), suggest that the inclusion of boron as an additive can modulate the defect concentration of the products. ZrB 2 powders with varied dislocation densities were achieved through meticulously controlled synthesis methods, followed by subsequent densification via hot pressing sintering. The results indicated that the relative density of ZrB 2 ceramics increased from 83.9 % to 96.7 % as the dislocation density of the powder increased from 2.7 × 10 13 m −2 to 7.6 × 10 14 m −2 with the rise in boron content from 0 wt% to 3 wt%. In addition, the defects create extra sintering-driving forces that induce a shift in the densification mechanism from grain boundary diffusion to dislocation slip during hot-pressing sintering. This shift results in an increase in the apparent activation energy from 105 kJ/mol to 210 kJ/mol.

Fabrication of ZrB2 Ceramics by Reactive Hot Pressing of ZrB and B

Chemical Process and Solid Solution Formation in Reactive Hot Pressed ZrB2–SiC Ceramics Doped with W

Dense Submicron-Sized ZrC – W Composite Produced by Reactive Melt in Fi Ltration at 1200 ° C

Fully dense ZrB 2 ceramics by borothermal reduction with ultra‐fine ZrO 2 and solid solution

Defect-regulated synthesis of ZrB 2 powders via carbon thermal reduction and elucidation of its hot-pressing densification mechanism

Pressureless Sintering of Zirconium Diboride Ceramics with Boron Additive

Two-step Hot Pressing of Bimodal Micron/nano-Zrb2 Ceramic with Improved Mechanical Properties and Thermal Shock Resistance

Mechanical Properties of ZrB<sub>2</sub>-Based Ceramics Reinforced by Nano-SiC Whiskers

Novel (Zr, Ti)B2-(Zr, Ti)C-SiC ceramics via reactive hot pressing

In Situ ZrB2 Formation in B4C Ceramics and Its Strengthening Mechanism on Mechanical Properties

Monolithic ZrB 2 ‐based UHTC s using polymer‐derived Si(Zr,B)CN as sintering aid

Reactive sintering behavior and enhanced densification of (Ti,Zr)B2–(Zr,Ti)C composites

Microstructure and Mechanical Properties of ZrB2/h-BN Multiphase Ceramics by Low-Temperature Reactive Sintering

REACTIVE HOT PRESSING OF B4C–CrB2 CERAMICS AND ITS MECHANICAL PROPERTIES

Preparation and properties of zirconium diboride-based ultra-high temperature ceramics

Carbothermal Reduction Synthesis Of Zirconium Diboride Powders Assisted By Microwave

Effects of SiC Platelet and ZrSi2 Additive on Sintering and Mechanical Properties of ZrB2-based Ceramics by Hot-Pressing

Preparation and Mechanical Properties of ZrB2-based Ceramics Using MoSi2 As Sintering Aids

Influence of TiB2 and CrB2 on densification, microstructure, and mechanical properties of ZrB2 ceramics

In Situ Preparation and Mechanical Properties of (ZrB2+ZrC)/Zr3[Al(Si)]4C6 Composites

Enhanced Mechanical Properties and Oxidation Resistance of Zirconium Diboride Ceramics via Grain‐Refining and Dislocation Regulation