Abstract:Laser-induced transient heat load events such as edge localized mode (ELM) could induce recrystallization, grain growth, surface degradation, and hardness changes. In this regard, we used the long-pulse laser beams with power densities ranging from 0.165 to 1.909 GW m- 2 to simulate transient heat load events for pure tungsten and tungsten heavy alloy (WHA) materials. The investigated samples showed that pure tungsten exhibited a higher recrystallization threshold, steady grain growth, and less surface hardness deterioration than WHA. However, the real-time simultaneous analysis of structural and mechanical properties such as matrix elements, grain size, surface degradation, and hardness changes is challenging in this domain. Therefore, in this study, we utilized a novel laser Opto-ultrasonic dual detection (LOUD) multimodal technique that integrates the benefits of laser-induced breakdown spectroscopy (LIBS) and laser ultrasonic testing (LUT) for simultaneous and in-situ detection of elemental information, grain size and hardness. The preliminary results showed that the variation in hardness is well correlated with the LIBS calibration curve formed by the ionic to atomic line intensity ratio and plasma electron temperature (Te). Despite the different matrix compositions of both samples, the observed in-crease in the value of Te with hardness justifies the Saha-Eggert relation. The coefficient of determination (R2 >= 0.970) value in the calibration curve and Te for hardness evaluation showed the goodness of the fitted model. Furthermore, the correlation of grain size with ultrasonic acoustic attenuation (alpha) was analyzed by the pulse-echo technique of the ultrasonic waveform for investigated samples. The results showed that grain size is also directly associated with acoustic attenuation with R2 > 0.989. The findings showed that the regression coefficient has a good approximation, which demonstrates the preciseness and potential ability of the LOUD technique for in-situ grain size and hardness analysis.

In-situ Measurement of Ti-6Al-4V Grain Size Distribution Using Laser-Ultrasonic Technique

Non-contact Measurements of Residual Stress Distribution and Grain Size in Titanium Alloys with Laser Ultrasonic System

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

An Approach to Characterize the Compositional, Structural and Mechanical Properties of Thermally Processed Titanium (ti) Alloy Simultaneously Via Novel In-Situ Laser Opto-Ultrasonic Dual Detection (LOUD)

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Nondestructive measurement of the grain size of laser cladding coatings using a laser ultrasonic method

Laser Ultrasonic Characterization of Grains in Titanium Alloy by the Inversion Method

Simultaneous Compositional and Grain Size Measurements Using Laser Opto-Ultrasonic Dual Detection for Additive Manufacturing.

Grain Size Characterization by Laser-Based Ultrasonics Based on the Centroid Frequency Shift Method

Simultaneous Analysis of Long-Pulse Laser Irradiated Plasma-Facing Materials (pfms) Microstructure and Hardness by In-Situ Laser Opto-ultrasonic Dual Detection (LOUD)

Application of Laser Ultrasound in the Detection of Metal Microstructure

In-situ investigation into the deformation behavior of Ti-6Al-4V processed by laser powder bed fusion

Microstructure and Mechanical Properties of Laser Metal Deposited Ti6Al4V Alloy with Near Equiaxed Β Grain Structure

Grain refining of Ti-6Al-4V alloy fabricated by laser and wire additive manufacturing assisted with ultrasonic vibration

Twin and Dislocation Induced Grain Subdivision and Strengthening in Laser Shock Peened Ti

In-Situ SEM Study on Deformation and Failure Mechanism of TC4 Titanium Alloy by Laser Additive Manufacturing

In-situ Measurement of Near-Tip Fatigue Crack Displacement Variation in Laser Melting Deposited Ti-6.5Al-3.5Mo-1.5Zr-0.3Si Titanium Alloy

Investigation of Microstructural Evolution in a Selective Laser Melted Ti6Al4V Alloy Induced by an Ultrasonic Surface Rolling Process

Investigating the microstructural evolution during deformation of laser additive manufactured Ti–6Al–4V at 400 °C using in-situ EBSD

Analysis of laser power/scan speed combinations on constant energy density: Correlation of roughness-density and structure-property of additively manufactured Ti-6Al-4 V alloy

Microstructure Formation of Ti-6Al-4 V in Synchronous Induction Assisted Laser Deposition