Pico-Strain Resolution Fiber Grating Sensor With Ultralow Probe Power And Tunable Sensitivity

Shuangxiang Zhao,Qingwen Liu,Jiageng Chen,Zuyuan He

DOI: https://doi.org/10.1364/cleo_at.2018.jw2a.173

2018-01-01

Abstract:We present here a novel interrogation method for Er+-doped fiber grating sensor with p epsilon resolution, ultralow probe power, large tunable strain sensitivity and capability of multiplexed, static and dynamic sensing.

What problem does this paper attempt to address?

P $\varepsilon$ -Resolution Fiber Grating Sensor with Adjustable Measurement Range and Ultralow Probe Power

Shuangxiang Zhao,Qingwen Liu,Jiageng Chen,Zuyuan He

DOI: https://doi.org/10.1109/lpt.2018.2880793

IF: 2.6

2019-01-01

IEEE Photonics Technology Letters

Abstract:A novel active fiber grating sensor system based on injection-locking and Pound-Drever-Hall techniques is presented. In demonstrational experiments, epsilon-level strain resolution is achieved with a very low probe power down to -70 dBm, which is at least 50 dB lower compared with the classical PoundDrever- Hall technique. Besides, the measurement range of the sensor can be adjusted over a large scale up to 17 dB by changing the injection ratio. With the ultrahigh resolution, ultralow probe power, and adjustable measurement range, the proposed sensor has great potential in high-resolution and large-scale sensor networks.
Pico-strain resolution multiplexed fiber grating sensor array using one mode-locked laser

Shuangxiang Zhao,Qingwen Liu,Jiageng Chen,Zuyuan He

DOI: https://doi.org/10.1364/ofs.2018.wb3

2018-01-01

Abstract:A mode-locked laser works as the source to interrogate Er3+-doped fiber grating sensor array with wavelength-division-multiplexing technology. Combined with the Pound-Drever-Hall and injection-locking technologies, pico-strain resolution down to sub-herz is demonstrated in experiments.
Pico-Strain Resolution Multiplexed Fiber Grating Sensor Array Interrogated with Mode-Locked Laser

Shuangxiang Zhao,Qingwen Liu,Jiageng Chen,Zuyuan He

DOI: https://doi.org/10.1109/jlt.2019.2923424

2018-01-01

Abstract:A multiplexed fiber grating sensor system based on injection-locking and high-order Pound–Drever–Hall techniques is presented. In the sensor system, two distributed feedback fiber lasers and a mode-locked laser are employed as the sensor array and probe laser, respectively. The weak comb teeth of the mode-locked laser are injection locked to corresponding sensing elements, to suppress the free running noise of the laser sensors and thus interrogate the sensor array. A high strain resolution of 72 p$\boldsymbol {\varepsilon }$ in 100 s and 4 p$\varepsilon$/${\surd }$ Hz above 10 Hz is proved. The proposed method allows the direct use of optical frequency comb as the light source in fiber grating sensor system. We believe this achievement is of great significance for fiber grating sensors in both sensing resolution and multiplexing scale.
Fiber Grating Sensor Using Dynamic PZT Modulation

Qiang Li

2002-01-01

Abstract:A new type technology of dynamic PZT modulation with fiber grating is proposed. It can change measure of wvelength shift with optical spectrum analyzes to count of optical power pulse detecting by oscilloscope. The technology is investigated theoretically and experimentally. The PZT is modulated by periodicity voltage and the fiber grating fixing on the it is also modulated by PZT. The measured resolutions in experiment are good agreement with ones in theory.
Pico-strain Resolution Fiber-Optic Sensor with White-Light Interferometry

Shuting Liu,Qingwen Liu,Shuangxiang Zhao,Zuyuan He

DOI: https://doi.org/10.1364/ol.456466

IF: 3.6

2022-01-01

Optics Letters

Abstract:The fiber Bragg grating (FBG) sensor is well known for simple fabrication, absolute measurement, inherent multiplexing capability, etc. To date, most FBG sensors that use a broadband light source for demodulation can only achieve resolution at the mu epsilon level. In this Letter, we propose a white-light-driven self-reference sensing system with FBGs, using a Mach-Zehnder interferometer (MZI) and a white light source, to realize multiplexed high-resolution vibration sensing with a very simple system configuration. A strain resolution of 35p epsilon/root HZ at 1 kHz is demonstrated, which is several orders of magnitude better than the current FBG sensor systems with white light sources. The performance of the sensing system is analyzed, and multiplexing capability is also experimentally evaluated; there is no observable cross talk. (C) 2022 Optica Publishing Group
Large detection range and high strain sensitivity fiber SPR sensor based on wave structure

Yong Wei,Puxi Ren,Chunlan Liu,Tianci Jiang,Chunbiao Liu,Chen Shi,Yixiong Tang,Ziqiang Zhang,Zhihai Liu

DOI: https://doi.org/10.1364/OE.521801

2024-04-22

Abstract:To achieve a fiber strain sensor with a large detection range and high sensitivity, this paper proposes a wave structured fiber SPR strain sensor. When subjected to axial strain, the wave structured fiber is stretched axially, increasing the stretchability of the sensor and achieving a large detection range strain sensing. Meanwhile, axial strain reduces the longitudinal amplitude of the fiber wave structure, effectively changing the total reflection angle of the transmitted beam at the peak and valley (SPR incidence angle) to achieve high sensitivity SPR strain sensing. The experiment indicates that the strain detection range of the sensor can reach 0-1800µε, with a maximum strain sensitivity of 36.25pm/µε. The wave structured fiber SPR strain sensor designed in this article provides a new approach to improve the range and sensitivity of strain detection.
High-Sensitivity Microfiber Strain and Force Sensors

Wei Li,Zhifang Hu,Xiyuan Li,Wei Fang,Xin Guo,Limin Tong,Jingyi Lou

DOI: https://doi.org/10.1016/j.optcom.2013.09.072

IF: 2.4

2014-01-01

Optics Communications

Abstract:A microfiber biconically tapered from a standard optical fiber shows obvious sinusoidal oscillatory transmission spectrum due to the multimode interference, with evident blue-shifted peak wavelength when applying an axial force. Based on this force-induced spectral shift, here we experimentally demonstrate compact microfiber strain and force sensors with low optical power and high sensitivity. With a 1.5-μW probing light, measured sensitivity of a 2.5-μm-diameter microfiber for the strain and elongation sensing are 4.84pm/με and 404pm/μm respectively, with a force detection limit down to 50μN.
Sensitivity-Enhanced Strain Sensor With a Wide Dynamic Range Based on a Novel Long-Period Fiber Grating

Xudong Chen,Wenhuan Chen,Yue Liu,Shijie Liu,Shuo Zhang,Qi Yan,Weimin Sun,Tao Geng

DOI: https://doi.org/10.1109/jsen.2021.3136445

IF: 4.3

2022-02-15

IEEE Sensors Journal

Abstract:A long period fiber grating prepared by multimode fibers (MMF-LPFG) is proposed and experimentally demonstrated as a sensitivity-enhanced strain sensor. The core diameter mismatch between the MMFs excites the high order cladding mode to obtain a compact sensing structure (3.6 mm). The strain sensitivity of the MMF-LPFG structure is enhanced to −15.06 pm/$\mu \varepsilon $ when the grating period is closer to the dispersion turning point (DTP). Meanwhile, the novel fiber structure also has an excellent mechanical property to achieve a large dynamic range ($\text{0-4508} ~\mu \varepsilon $ ) in strain measurement.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
High-Resolution and Large-Dynamic Range Fiber-Optic Sensors Based on Dual-Mode Direct Spectrum Interrogation Method

Min Zhou,Zhe Zhang,Qingyue Cui,Qingdian Lin,Jun Yu,Xiaoyang Guo,Cangtao Zhou,Shuangchen Ruan

DOI: https://doi.org/10.3390/s24123996

IF: 3.9

2024-06-20

Sensors

Abstract:Conventional optical fiber temperature/strain sensors often have to make compromises between the resolution and the dynamic range. Here we present a new method that meets the measurement requirements for both high resolution and large dynamic range. A high-quality optical fiber Fabry-Perot Interferometer (FPI) constructed using a pair of chirped fiber Bragg gratings is employed as the sensor and a dual-mode direct spectrum interrogation method is proposed to identify the small drift of external temperature or strain. As a proof-of-concept illustration, a temperature resolution of 0.2 °C within 30–130 °C is demonstrated. For strain sensing, the resolution can be 10 με within 0–1000 με. The measurement resolution can be improved further by routinely increasing the reflectivity of the CFBG and the cavity length and the sensor can also be mass-produced. This new sensing schema not only resolves the conflict between the resolution and the dynamic range of fiber-optic temperature/strain sensors but can also be extended to other sensors and measurands.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Sub-nano resolution fiber-optic static strain sensor using a sideband interrogation technique.

Qingwen Liu,Tomochika Tokunaga,Zuyuan He

DOI: https://doi.org/10.1364/OL.37.000434

IF: 3.6

2012-01-01

Optics Letters

Abstract:We propose a novel sideband interrogation technique with multiplex radio frequency intensity and phase modulation to measure the resonance frequency difference between two optical resonators. Based on this new technique, an ultrahighly sensitive fiber-optic static strain sensor system consisting of a pair of identical fiber Fabry-Perot interferometers is built by incorporating a cross-correlation data processing algorithm. A static strain resolution down to 0.8 ne is demonstrated experimentally, which makes the sensor system a useful tool for geophysical research applications. (C) 2012 Optical Society of America
An Ultra-High-resolution Large-Dynamic-range Fiber Optic Static Strain Sensor Using Pound-Drever-Hall Technique

Qingwen Liu,Tomochika Tokunaga,Zuyuan He

DOI: https://doi.org/10.1364/ol.36.004044

2011-01-01

Abstract:In this paper we report the realization of a fiber optic static strain sensor with ultra-high resolution and large dynamic range for the applications of geophysical research. The sensor consists of a pair of fiber Bragg grating based Fabry-Perot interferometers for strain sensing and reference, respectively. Pound-Drever-Hall technique is employed to interrogate the sensor heads, and a cross-correlation algorithm is used to figure out the strain information with high precision. Static strain resolution down to 4.5 nε was demonstrated. The dynamic range can be extended up to hundreds of με, and the measuring period is a few tens of seconds.
Highly Sensitive Long-Period Fiber-Grating Strain Sensor with Low Temperature Sensitivity

Yi-Ping Wang,Limin Xiao,D. N. Wang,Wei Jin

DOI: https://doi.org/10.1364/ol.31.003414

IF: 3.6

2006-01-01

Optics Letters

Abstract:A long-period fiber-grating sensor with a high strain sensitivity of -7.6 pm/microepsilon and a low temperature sensitivity of 3.91 pm/ degrees C is fabricated by use of focused CO(2) laser beam to carve periodic grooves on a large- mode-area photonic crystal fiber. Such a strain sensor can effectively reduce the cross-sensitivity between strain and temperature, and the temperature-induced strain error obtained is only 0.5 microepsilon/ degrees C without using temperature compensation.
Ultrahigh resolution optical fiber strain sensor using dual Pound-Drever-Hall feedback loops.

Jiageng Chen,Qingwen Liu,Xinyu Fan,Zuyuan He

DOI: https://doi.org/10.1364/OL.41.001066

IF: 3.6

2016-01-01

Optics Letters

Abstract:We present an ultrahigh resolution optical fiber strain sensor with a broad frequency range from quasi-static to several hundred hertz. The sensor consists of a pi-phase shifted fiber Bragg grating for strain sensing and a fiber Fabry-Perot interferometer as reference. The laser carrier and sideband are locked to the reference and sensing elements, respectively, via two individual feedback loops, in which the Pound-Drever-Hall technique is employed to generate the error signals. The sampling rate is up to 500 samples/s in the demonstrational experiments, only limited by the updating rate of the frequency counter. The strain resolution exhibits a 1/f characteristic in the bandwidth of 0.01-250 Hz, and is better than 0.01 ne at 10 Hz with a dynamic range up to 149 dB. Compared with the traditional static strain sensors, the proposed sensor shows a great improvement in both resolution and sensing bandwidth, and can be a powerful tool for geophysical applications. (C) 2016 Optical Society of America
High resolution fiber grating dynamic strain sensor with broadband light

Shuting Liu,Qingwen Liu,Shuangxiang Zhao,Zuyuan He

DOI: https://doi.org/10.1364/cleo_at.2022.jw3b.10

2022-01-01

Abstract:A fiber grating strain sensing system based on self-reference mechanism was developed. The resolution is 34.6pε/√Hz at 1kHz, which is several orders of magnitude better than traditional FBG systems.
0.1-Nano-strain Resolution Fiber Optic Sensor for Quasi-Static Strain Measurement with 1 Ks/s Sampling Rate

Jiageng Chen,Qingwen Liu,Xinyu Fan,Lin Ma,Jiangbing Du,Tomochik Tokunaga,Zuyuan He

DOI: https://doi.org/10.1117/12.2194700

2015-01-01

Abstract:We present a newly developed high performance fiber optics sensor for quasi-static strain measurement. The sensor consists of a piece of π-phase shifted FBG for static strain sensing, and fiber Fabry-Perot interferometer for reference, interrogated by an improved sideband interrogation method with real-time feedback loops. Strain resolution of 0.12 nano-strain was achieved with sampling rate up to 1 kS/s in laboratory experiments. Compared with previous sensor systems, the proposed method shows great improvement in the sensing rate as well as the resolution.
A Simple Strain Sensor Using Polymer Fiber Bragg Grating and Long-Period Fiber Grating

HB Liu,HY Liu,T Whitbread,YJ Rao,GD Peng

DOI: https://doi.org/10.1117/12.580654

2004-01-01

Abstract:We develop a simple strain sensor using polymer optical fibre Bragg grating and long period fibre grating. The sensor head is formed by a polymer optical fiber Bragg grating. A long period fibre grating is used for strain related wavelength shift demodulation. This particular combination of two quite different gratings could offer very large dynamic, up to tens of thousands micro-strains, for strain sensing. The preliminary experimental results have demonstrated that this sensing scheme provides good linearity, high resolution and large dynamic range.
Sub-Nano-Strain Multiplexed Fiber Optic Sensor Array for Quasi-Static Strain Measurement

Jiageng Chen,Qingwen Liu,Xinyu Fan,Zuyuan He

DOI: https://doi.org/10.1109/lpt.2016.2592506

IF: 2.6

2016-01-01

IEEE Photonics Technology Letters

Abstract:This letter presents a high resolution multiplexed strain sensor for quasi-static strain measurement based on π-phase-shifted fiber Bragg gratings (π-PSFBGs). The sensor array is composed by four π-PSFBGs in parallel with different delay lines, and a time-division multiplexing scheme is proposed to interrogate the π-PSFBGs in turn. The Pound-Drever-Hall technique and the sideband interrogation method are employed to improve the resolution and the sampling rate. In the demonstrational experiment, three-channel quasi-static strain sensing is realized with a resolution better than 0.4 n and a sampling rate of 100 samples/s.
Research On Sensing Characteristics Of Low-Finesse Fiber-Optic Fabry-Perot Cavity

Zhao Jiang-Hai,Ye Xiao-Dong,Sun Shao-Min,Xu Lin-Sen

DOI: https://doi.org/10.1117/12.966803

2012-01-01

Abstract:The Low-Finesse Fabry-Perot(F-P) cavity, as a kind of fiber-optic sensor probe frequently used, can be applied to detect physical parameters of strain, temperature, acoustic wave, pressure, and so on, and is an important optical sensing component. In this paper, sensing properties of low-finesse F-P cavity is deeply and systemically analyzed. At first, the interference principle of F-P cavity is illuminated from three aspects which include the distribution of light power, the characteristic of interference fringe and the sensitivity. Considering the spectrum of incident beam obeys a Gaussian distribution, the intensity distribution of reflected beam is approximate to a cosine function within a Gaussian envelope and the visibility of interference fringes follows a Gaussian distribution also. Moreover, the operating point of low finesse F-P cavity must be held near the quadrature-point for the maximum sensitivity. The operating characteristic of F-P cavity is analyzed from three aspects including linearity, property of temperature and contrast of fringe. Analyzing results show that the F-P cavity can offer the linearity of 2.2%, and the fringe contrast drops as the length of F-P cavity increases. In addition, the F-P cavity is insensitive to the change of environmental temperature and possesses an excellent capability to suppress the temperature disturbance. Finally, a test scheme is established to verify the sensor performance of F-P probe. Test results indicate that the F-P cavity offers the sensitivity of 7.5V/um and the measuring accuracy of 9.4nm, and can well satisfies the practical requirement.
A dual-wavelength erbium-doped fiber laser for high resolution strain sensing with compound filter of a Sagnac loop and a long period fiber grating

Lida Li,Hailiang Chen,Ruyue Shi,Hongwei Li

DOI: https://doi.org/10.1016/j.optlastec.2024.110787

IF: 4.939

2024-08-01

Optics & Laser Technology

Abstract:A dual-wavelength erbium-doped fiber laser (EDFL) strain sensing system composed of compound filter of a long period fiber grating (LPFG) and a Sagnac loop is proposed. Polarization maintaining fiber (PMF) in Sagnac loop acts both an interference filter and a strain sensing probe with high sensitivity, low cost, and low loss. LPFG is used to modulate the transmission wavelength and bandwidth of EDFL through adjusting its bending curvature. Flexible laser output with single wavelength and dual-wavelength tunable wavelength band of 10 nm is achieved in EDFL. The measurement sensitivity of strain reaches 8.33 pm/με, while the 3 dB linewidth is less than 2 nm and the signal-to-noise ratio (SNR) exceed 36 dB. This sensor has a high resolution (R) of 0.11 nm and a high quality factor (Q) of 38.13. The experimental results suggest that the system is suitable for precise strain measurement and has significant potential in fields like biomedicine, environmental monitoring, health monitoring, and aerospace.

optics,physics, applied
Deeply-Tapered Ultrashort Long-Period Fiber Grating and Its Application to Ultrasensitive Transverse-Load Sensor

Chengliang Zhu,Shuai Huang,Xinyue Meng,Yong Zhao,Hongpu Li

DOI: https://doi.org/10.1109/jlt.2023.3275589

IF: 4.7

2023-01-01

Journal of Lightwave Technology

Abstract:Deeply-tapered long-period fiber gratings (DT-LPFGs) have been demonstrated, which are fabricated by using the cylindrical-lens-assisted CO2 laser technique. Attributed to the effects of both the refractive-index perturbation and geometrical perturbation in the deeply-tapered structure, the proposed DT-LPFG is of the high coupling-efficiency and thus an ultrashort yet strong LPFG can be achieved. As a typical example, a LPFG with a length of only ∼1 mm and loss-dip of ∼ 33 dB in spectrum has been successfully obtained, which, based on our knowledge, is the shortest one among all those of the strong LPFGs reported to date. The fabricated DT-LPFG is also of the low polarization-dependence, which considerably benefits the practical application of grating itself. As an application of the proposed DT-LPFG, a transverse load sensor with sensitivity up to 1246.594 nm/(N/mm) has been successfully demonstrated, which represents the best result among all those of the fiber-based transverse load sensors.

engineering, electrical & electronic,optics,telecommunications

Pico-Strain Resolution Fiber Grating Sensor With Ultralow Probe Power And Tunable Sensitivity

P $\varepsilon$ -Resolution Fiber Grating Sensor with Adjustable Measurement Range and Ultralow Probe Power

Pico-strain resolution multiplexed fiber grating sensor array using one mode-locked laser

Pico-Strain Resolution Multiplexed Fiber Grating Sensor Array Interrogated with Mode-Locked Laser

Fiber Grating Sensor Using Dynamic PZT Modulation

Pico-strain Resolution Fiber-Optic Sensor with White-Light Interferometry

Large detection range and high strain sensitivity fiber SPR sensor based on wave structure

High-Sensitivity Microfiber Strain and Force Sensors

Sensitivity-Enhanced Strain Sensor With a Wide Dynamic Range Based on a Novel Long-Period Fiber Grating

High-Resolution and Large-Dynamic Range Fiber-Optic Sensors Based on Dual-Mode Direct Spectrum Interrogation Method

Sub-nano resolution fiber-optic static strain sensor using a sideband interrogation technique.

An Ultra-High-resolution Large-Dynamic-range Fiber Optic Static Strain Sensor Using Pound-Drever-Hall Technique

Highly Sensitive Long-Period Fiber-Grating Strain Sensor with Low Temperature Sensitivity

Ultrahigh resolution optical fiber strain sensor using dual Pound-Drever-Hall feedback loops.

High resolution fiber grating dynamic strain sensor with broadband light

0.1-Nano-strain Resolution Fiber Optic Sensor for Quasi-Static Strain Measurement with 1 Ks/s Sampling Rate

A Simple Strain Sensor Using Polymer Fiber Bragg Grating and Long-Period Fiber Grating

Sub-Nano-Strain Multiplexed Fiber Optic Sensor Array for Quasi-Static Strain Measurement

Research On Sensing Characteristics Of Low-Finesse Fiber-Optic Fabry-Perot Cavity

A dual-wavelength erbium-doped fiber laser for high resolution strain sensing with compound filter of a Sagnac loop and a long period fiber grating

Deeply-Tapered Ultrashort Long-Period Fiber Grating and Its Application to Ultrasensitive Transverse-Load Sensor