Abstract:The ever-increasing demand for higher I/O counts on chip requires the finer pitches to improve the performance, cost effectiveness and higher yield. The conventional under bump metallization (UBM) technology may not guarantee the required performance due to higher current density and diffusivity nowadays. In order to overcome these challenges, a UBM with higher strength and resistance to diffusion, better thermal and microstructural properties are required. Recently, nano reinforced Ni-P alloy has been identified as potential approach. Especially, the addition of Carbon nanotube (CNT) was expected to provide strengthening to the resulting UBM layers. CNTs have exceptional and attractive thermal, electrical, and mechanical properties, and are believed to be ideal material for fabricating composites. However, due to the large surface volume ratio, CNTs have strong tendency to agglomerate, which results in clusters. CNT clusters may lead to void formation and further cracking. Therefore, it is of great importance to figure out methods to disperse and incorporate CNTs into Ni-P UBM. In order to disperse carbon nano-tubes in electroless Ni-P coatings, two approaches were employed. Chemical modification, which includes acid oxidation treatment and surfactant treatment were conducted to disperse CNT clusters. Meanwhile, magnetic stirring and ultrasonic agitation were also employed to prepare the CNT/Ni-P composite coatings with CNTs homogeneously embedded. SEM and TEM were used to observe the dispersion after adopting the aforementioned treatment as well as the surface morphology of the deposited layers. It was verified that the dispersion can be significantly improved after proper treatment process, and surface of the CNT/Ni-P was quite smooth; CNTs were equably dispersed throughout the matrix. In addition, the interfacial bonding between CNTs and Ni-P coatings was good and firm. In these cases, an understanding of the effects of the acid oxidation, surfactant dispersant- magnetic stirring and ultrasonic agitation on CNT dispersion in both solution and deposited layer were ascertained.

A Comparative Study of Effect of Mechanical and Ultrasound Agitation on the Properties of Pulse Electrodeposited Ni-W/MWCNTs Composite Coatings

Effect of ultrasonic on properties of electroplated diamond tools

Influence of processing parameters on final characteristics of Ni-P-MWCNT coatings produced by pulsed electrodeposition

Microstructure and Mechanical Properties of ABOw and Nickel-Coated MWCNTs Reinforced 2024al Hybrid Composite Fabricated by Squeeze Casting

Influence of ultrasonic assistance on the microstructure and friction properties of laser cladded Ni60/WC composite coatings

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Effect of Pulse Electrodeposition Mode on Microstructures and Properties of Ni-TiN Composite Coatings

Study on Preparation and Wear Resistance of Nicrbsi-Wc/Co Composite Coatings by Pulsed Magnetic Field Assisted Supersonic Plasma Spraying

Microstructure and Properties of FeMnCrAl/Ni Coated WC Coatings Deposited by High Velocity Arc Spraying

Effective method to disperse and incorporate Carbon nanotubes in electroless Ni-P deposits

Enhanced mechanical and wear properties of Ni-W-SiC composite coatings by synergistic influence of micro-nano SiC mixture

The Influences of Ultrasonic Vibrations on Laser Cladding Ni60/WC-TiO2+La2O3 Composite Coating

Influences of Mwcnts Concentration on the Friction and Anti-Wear Behavior of Ni-P Coating

Microstructure Characterisation, Hardness, and Corrosion Behaviour of Nickel-Silicon Carbide Electrodeposition Coating with The Influence of Ultrasonic Agitation

Superhydrophobic and anticorrosion Ni-B/WC@MoS 2 composite coatings deposited via jet electrodeposition assisted with ultrasonics

Microstructure, Friction, And Wear Properties Of Ni-Al2o3-Mos2 Composite Coatings

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Influence of the bath pH value on the microstructure and properties of a novel electrodeposited Ni-W-Ti3C2TX composite coating

Preparation and Characterization of Pulse Electrodeposited Ni/W-SiC Nanocomposite Coating on Mild Steel Substrate