Abstract:For the fabrication of high-strength carbon nanotube (CNT) reinforced Al matrix composites, the uniform dispersion, strong interface bonding and high structural integrity of CNTs have been regarded as the three most important issues. In this work, two distinct approaches, namely high shear dispersion (HSD) and shift-speed ball milling (SSBM), were applied to disperse CNTs (1.5 wt%) into pure Al powders. These two kinds of CNT/Al composite powders as well as the pure Al powder (as a comparison) were deposited onto stainless steel plates by cold spraying using different processing parameters. The velocity and the temperature of the particle prior to impact was simulated by the commercial code of Fluent. The deposition efficiency, microstructure evolution, as well as the distribution and structural integrity of CNTs in the composite coatings produced from different starting powders were comparatively investigated in terms of X-ray diffraction (XRD), Raman spectra, and electron back scanning diffraction (EBSD). According to the XRD and Raman analysis, no new phases such as oxides or brittle Al4C3 were detectable in both CNT/Al composite coatings. Some structural damages of CNTs were found in both composite coatings, especially the one fabricated from HSD composite powder. The dispersion of CNTs onto Al particle surfaces by HSD approach did not achieve a significant strengthening effect on the composite coatings, but adversely affected the metallic bonding of the particles and the substrate. The microhardness of the CNT/Al composite coating produced from SSBM powders reached around ~115 HV0.1, showing a significant improvement compared to the pure Al coating mainly due to the grain refinement and CNTs strengthening.

Design of an Efficient Flake Powder Metallurgy Route to Fabricate CNT/6061Al Composites

Enhanced Interfacial Bonding and Mechanical Properties in CNT/Al Composites Fabricated by Flake Powder Metallurgy

The Use of Flake Powder Metallurgy to Produce Carbon Nanotube (cnt)/aluminum Composites with a Homogenous CNT Distribution

High-strength CNT/Al-Zn-Mg-Cu Composites with Improved Ductility Achieved by Flake Powder Metallurgy Via Elemental Alloying

Smart Mechanical Powder Processing for Producing Carbon Nanotube Reinforced Aluminum Matrix Composites

Tailoring and Characterization of Carbon Nanotube Dispersity in CNT/6061Al Composites

Balanced strength and ductility in CNT/Al composites achieved by flake powder metallurgy via shift-speed ball milling

Fabrication and Mechanical Properties of CNT/Al Composites Via Shift-Speed Ball Milling and Hot-Rolling

Synthesis of uniformly dispersed carbon nanotube reinforcement in Al powder for preparing reinforced Al composites

Enhanced ductility by Mg addition in the CNT/Al-Cu composites via flake powder metallurgy

Powder Assembly & Alloying to CNT/Al–Cu–Mg Composites with Trimodal Grain Structure and Strength-Ductility Synergy

Synthesis of Carbon Nanotube Reinforced Al Matrix Composites Via Cold Spray Deposition

A Powder Metallurgy Route to Fabricate CNT-reinforced Molybdenum-Hafnium-carbon Composites

A New Technique for Dispersion of Carbon Nanotube in A Metal Melt

Synthesis of carbon nanotube reinforced Al matrix composite coatings via cold spray deposition

Heat Treatment Behavior and Strengthening Mechanisms of CNT/6061Al Composites Fabricated by Flake Powder Metallurgy

Wet Powder Metallurgy Process for Dispersing Carbon Nanotubes and Fabricating Magnesium Composite

Simultaneous Enhancement of Dispersion and Interfacial Adhesion in Al Matrix Composites Reinforced with Nanoceramic-Decorated Carbon Nanotubes

Effectively Reinforced Load Transfer and Fracture Elongation by Forming Al4C3 for In-Situ Synthesizing Carbon Nanotube Reinforced Al Matrix Composites

Preparation and Characterization of Nanodiamond-Reinforced 6061 Aluminum Matrix Composites Via a Slurry Process and High-Energy Ball Milling

Study on the Properties of Carbon Nanotube (CNTs) Reinforced AlSi10Mg Composites Fabricated by Powder Metallurgy