Abstract:Summary Radial jet drilling (RJD) involves drilling several small-diameter lateral holes from a single vertical wellbore to increase reservoir contact and production. RJD system components (diverter, flexible hose, and jetting bit) are conveyed to the target depth using coiled tubing. A high-pressure flexible hose is used in conjunction with a jetting bit to drill holes laterally. Without a rigid drillstring, no axial force can be transferred to the bit as it penetrates the rock. As a result, the bit is propelled by hydraulic means. Thus, in addition to front-jetting nozzles, RJD bits use back-jetting nozzles. Therefore, the rate of penetration (ROP) and maximum hole length (MHL) must be maximized through proper hydraulic optimization. Existing hydraulic models rely on field-measured parameters (discharge coefficient and flow rate ratio) that vary by the bit design to predict the propulsion force, bit hydraulic power, and the maximum lateral hole length. Hence, this study aims to develop a generalized and accurate hydraulic model that does not require field-measured parameters to make predictions. As a result, the new model can be used for optimizing RJD operations by selecting suitable bit designs and lateral hole geometries. This article presents a new RJD hydraulic model that uses a discharge coefficient that varies with the nozzle aspect ratio. The model predicts the propulsion force, differential pressure across the bit, and MHL based on the design of the bit, nozzle, and lateral hole geometries, and flow rate. To verify the model, extensive experiments were conducted with single-nozzle and multi-nozzle jetting bits. The pump pressure was varied while flow rate and propulsion force were recorded during the tests. Model predictions are compared and validated with experimental data. Measured and model-predicted propulsion forces demonstrate a reasonable agreement with a maximum discrepancy of 25%. Once the model has been validated, it is used to perform a parametric study to investigate the influence of various factors on bit performance. According to the parametric study, nozzle and hole diameters, friction factor, and hose density strongly influence bit performance. Furthermore, the diameter of the nozzle has been found to have a significant effect on bit performance parameters (propulsion force, bit hydraulic power, and MHL).

Numerical Simulation on the Flow Field of Self-Propelled Multi-Orifices Nozzle for Ultra-Short Radius Radial Jet Drilling

Numerical Simulation of flow characteristics in a new-type multistage nozzle of pressure drop

Flow Field Simulation of Swirling Abrasive Jet Nozzle for Hard Rock Breaking

Numerical Study on the Effect of a Lobed Nozzle on the Flow Characteristics of Submerged Exhaust

Rock Breaking Characteristics of the Self-rotating Multi-orifice Nozzle for Sandstone Radial Jet Drilling

Three-Dimensional Numerical Simulation of Air Exhausted from Submerged Nozzles

Experimental investigation of internal and external flow fields of jetting nozzles with different structures

Internal Flow Simulation and Experimental Study of Non-moving Component Jet Oscillation Tool

Numerical investigation into the abrasive particle movement characteristics inside the swirling impeller nozzle based on the coupled SPH-FEM method

Numerical Analysis of Swirling-Abrasive Water Jet Flow in the Nozzle

Analytical and Numerical Simulation of Asymmetric Converging Flow of Gas Under Drill Bits in Reverse Circulation Gas Drilling

Numerical Simulation Study of Hydraulic Fracturing Nozzle Erosion in Deep Well

Optimization of Abrasive Water Jet Nozzle Based on Numerical Simulation

A Generalized Hydraulic Model for Propulsion Force Calculations in Radial Jet Drilling

Numerical and experimental investigation of flow in swirling nozzle

STUDY ON NUMERICAL SIMULATIONS OF A PLUG NOZZLE FOR ROCKET ENGINE

Study of the rock-breaking and drilling performance of a self-rotatory water-jet bit in water-jet drilling and its influential factors

Research on Multiphase Flow and Nozzle Wear in a High-Pressure Abrasive Water Jet Cutting Head

Research on the structures and hydraulic performances of the typical direct jet nozzles for water jet technology

Numerical Simulation on Field Characteristics of the Horizontal Gas Jet Flow of Underwater Vehicle

Study on Great Flow Nozzle Performance with CFD Method