Abstract:LNG floating production storage and offloading (FPSO) unit is a new type of floating production unit developed for offshore natural gas fields. It performs the functions of natural gas extraction, pretreatment, liquefaction, and storage. In this study, the heat transfer characteristics of a spiral-wound heat exchanger were studied using numerical simulations, which provides a basis for equipment selection and structural optimization of spiral-wound heat exchangers. The main research contents and conclusions are as follows. Under land-based simulation conditions, the heat transfer coefficient of the shell side of the spiral-wound heat exchanger decreases with an increase in the winding angle of the heat exchange tube, decreases with an increase in the spacing of the heat exchange tube, and increases with an increase in the outer diameter of the heat exchange tube. When the winding angle increased from 5° to 8°, the heat transfer coefficient decreased by 6.70%. The heat transfer coefficient of the shell side decreased by 13.21% when the heat exchange tube spacing increased from 14 to 17 mm. The heat transfer coefficient of the shell side increased by 22.89% when the outer diameter of the heat exchange tube increased from 9 to 12 mm. When the sloshing angle is constant, the heat transfer coefficient of the spiral-wound heat exchanger decreases with an increase in the winding angle and spacing of the heat exchange tubes, and increases with an increase in the outer diameter of the heat exchange tubes. When the structural parameters of the heat exchanger are constant, the heat transfer coefficient decreases as the sloshing angle increases. When the sloshing angle was less than 3°, the sloshing promoted heat transfer on the shell side. When the sloshing angle was higher than 7°, the heat transfer effect of the shell side deteriorated considerably, which weakened the heat transfer performance of the heat exchanger. When the sloshing period is constant, the heat transfer coefficient of the wound heat exchanger decreases with an increase in the winding angle and spacing of the heat exchange tubes, and increases with an increase in the outer diameter of the heat exchange tubes. When the structural parameters of the heat exchanger are constant, the heat transfer coefficient increases with sloshing period. When the sloshing period was greater than 15 s, the influence of sloshing on the heat transfer on the shell side of the heat exchanger was relatively weak.

The Heat Transfer Characteristic of Shell-Side Film Flow in Spiral Wound Heat Exchanger under Rolling Working Conditions

Numerical Study on the Shell-Side Flow and Heat Transfer of Superheated Vapor Flow in Spiral Wound Heat Exchanger under Rolling Working Conditions

Numerical study on the flow characteristic of shell-side film flow of floating LNG spiral wound heat exchanger

Numerical Study on Shell-Side Saturated Boiling Heat Transfer in Spiral Wound Heat Exchanger

Shell-side heat transfer characteristics of floating liquefied natural gas spiral wound heat exchanger under sloshing conditions

Numerical Study of Heat Transfer Characteristic for Subcooled Falling Film outside the Shaped Tubes under Rolling Motion

A Mathematical Model of Floating LNG Spiral-Wound Heat Exchangers under Rolling Conditions

Numerical Investigation on Shear Flow and Boiling Heat Transfer on Shell-Side of LNG Spiral Wound Heat Exchanger

Numerical Study on Condensation Heat Transfer and Pressure Drop Characteristics of Methane Upward Flow in a Spiral Pipe under Sloshing Condition

Experimental Investigation on the Frictional Pressure Drop of Two-Phase Fluids in the Shell Side of LNG Spiral-Wound Heat Exchangers

Experimental and Numerical Investigation of Two-Phase Flow Outside Tube Bundle of Liquefied Natural Gas Spiral Wound Heat Exchangers under Offshore Conditions

Experimental Study of Flow Distribution Behavior on the Shell Side of Spiral Tube Bundles in LNG Spiral-Wound Heat Exchangers

Research on the falling film flow and heat transfer characteristics of FLNG spiral wound heat exchanger under sea conditions

Numerical study on shell-side flow and heat transfer of spiral-wound heat exchanger under sloshing working conditions

Analysis of Condensation Flow and Heat Transfer Characteristics Inside Spiral Tubes

Influences of working conditions on heat transfer characteristics in shell side of LNG spiral wound heat exchangers

Research on shell-side heat and mass transfer with multi-component in LNG spiral-wound heat exchanger under sloshing conditions

Numerical simulation of heat transfer performance of spiral wound heat exchanger under sloshing condition

Experimental Study on Optimizing Liquid Distribution in Spiral Wound Heat Exchangers: Influence of Two-Phase Flow Parameters and Geometry

Experimental and Numerical Investigation on Shell-side Performance of Multilayer Spiral-Wound Heat Exchangers

Liquid-migration Based Model for Predicting the Thermal Performance of Spiral Wound Heat Exchanger for Floating LNG