Abstract:Flow maldistribution could reduce the heat transfer capability of LNG spiral-wound heat exchangers (SWHEs). However, there remains a lack of clarity on the flow distribution behavior on the shell side of spiral tube bundles in SWHEs. To address the flow distribution behavior and improve distribution performance, we built a spiralwound heat exchanger test section with thirteen-layer spiral tube bundles and an experimental system. The experimental conditions were as follows, the gas mass flow rate ranged from 180.00 kg center dot h-1 to 256.50 kg center dot h-1, the liquid mass flow rate ranged from 173.88 kg center dot h-1 to 420.00 kg center dot h-1, and the vapor quality ranged from 0.30 to 0.54. The results suggest the distribution of two-phase flow becomes better when mass flow rate or vapor quality increases in the absence of the distributor and is superior to those of the gas flow and liquid flow. When the mass flow rate rises from 378.00 kg center dot h-1 to 475.00 kg center dot h-1, the distribution of two-phase flow improves by 48.78%. When vapor quality increases from 0.40 to 0.48, the distribution of the two-phase flow improves by 35.00%. The distributor can improve the distribution of two-phase flow on the shell side of spiral tube bundles. After setting the distributor, the gap in flow rate between inner channels and outer channels is reduced from 29.09% to 26.30% when vapor quality is 0.54, it is decreased from 42.68% to 30.08% when the mass flow rate is 500 kg center dot h-1. These results can be used for the design of LNG SWHEs.

Influences of working conditions on heat transfer characteristics in shell side of LNG spiral wound heat exchangers

Experimental Investigation on Downward Flow Boiling Heat Transfer Characteristics of Propane in Shell Side of LNG Spiral Wound Heat Exchanger

Influences of Tube Pitches on Heat Transfer and Pressure Drop Characteristics of Two-Phase Propane Flow Boiling in Shell Side of LNG Spiral Wound Heat Exchanger

Numerical simulation analysis of a heat transfer tube in SuperORV

Numerical Study on Thermal Performance of a BOG Heat Exchanger in the Inclined Condition

Numerical Study on Shell-Side Saturated Boiling Heat Transfer in Spiral Wound Heat Exchanger

Experimental Study of Flow Distribution Behavior on the Shell Side of Spiral Tube Bundles in LNG Spiral-Wound Heat Exchangers

Numerical Investigation on Shear Flow and Boiling Heat Transfer on Shell-Side of LNG Spiral Wound Heat Exchanger

Experimental Study on Optimizing Liquid Distribution in Spiral Wound Heat Exchangers: Influence of Two-Phase Flow Parameters and Geometry

Heat Transfer and Pressure Drop Characteristics of Two-Phase Propane Flow in Shell Side of LNG Spiral Wound Heat Exchanger

Analysis of Condensation Flow and Heat Transfer Characteristics Inside Spiral Tubes

Influence of Sloshing Conditions on the Pressure Drop and Heat Transfer of a Single-Layer Spiral-Wound LNG Heat Exchanger

Experimental Investigation on Heat Transfer Characteristics of Two-Phase Propane Flow Condensation in Shell Side of Helically Baffled Shell-and-tube Condenser

Heat Transfer Characteristics of Two-Phase Mixed Hydrocarbon Refrigerants Flow Boiling in Shell Side of LNG Spiral Wound Heat Exchanger

Numerical Study of Heat Transfer Characteristics in Bog Heat Exchanger

Numerical Study on the Shell-Side Flow and Heat Transfer of Superheated Vapor Flow in Spiral Wound Heat Exchanger under Rolling Working Conditions

The Heat Transfer Characteristic of Shell-Side Film Flow in Spiral Wound Heat Exchanger under Rolling Working Conditions

Numerical study on flow and heat transfer performance of a spiral-wound heat exchanger for natural gas

Experimental Investigation on Pressure Drop Characteristics of Two-Phase Hydrocarbon Mixtures Flow in the Shell Side of LNG Spiral Wound Heat Exchangers

Experimental Study of the Effects of Key Geometry Parameters on Shell-Side Vapor Condensation of Spiral-Wound Heat Exchangers

Experimental Study on the Tube-Side Thermal-Hydraulic Performance of Spiral Wound Heat Exchangers