Abstract:Three different heat treatment sequences, which alter the solute redistribution state in as-welded (AW) Aluminum Alloy 6061 resistance spot welds, were designed to investigate the effect of welding-induced microsegregation on the bake-strengthening ability of the joints. These sequences were postweld baking (AW-B), preweld solution treatment and postweld baking (SW-B), and postweld solution treatment and baking (WS-B). Vickers hardness and lap-shear test results showed that, compared with the AW samples, both the AW-B and SW-B samples experienced limited weld strengthening, while the WS-B sample welds experienced significant strengthening after baking (the strength was found to be comparable to that of the base metal). Calculation of the solidification path in the fusion zone using the Scheil-Gulliver model showed the effective solutes (Mg and Si) are segregated at the interdendritic regions in the AW samples (to form the beta-Mg2Si phase and eutectic), as confirmed by transmission electron microscopy. This reduced the degree of solute supersaturation, thereby significantly weakening the bake-strengthening ability of this site. Only the postweld solution treatment, which caused the effective solutes to diffuse into the Al-rich dendrites, could make the bake-hardening ability of the weld comparable to that of the base metal (confirmed by scanning transmission electron microscopy). Finally, digital image correlation analysis was conducted on a specially designed lap-shear test sample to reveal the local strain in the joints. It was found that, for the same weld size, the strain concentration occurred in the fusion zone of the AW and AW-B samples, and at the load-bearing site in the base metal of the SW-B and WS-B samples. Thus, the application of postweld solution treatment could improve the bake-strengthening ability of Aluminum Alloy 6061 resistance spot welded joints and increase the tendency of the joints to experience pullout failure.

Effect of Bake Hardening Treatment on the Mechanical Behaviors of Aluminum Alloy Spot Welding Joints

Bake-Strengthening Of Resistance Spot Welded Aluminum Alloy 6061

Influencing mechanism of inherent aluminum oxide film on coach peel performance of baked Al-Steel RSW

Effect of Forging Force on Fatigue Behavior of Spot Welded Joints of Aluminum Alloy 5182

Effects of pre-stretching and baking treatment on microstructural evolution and mechanical properties of 7A09 aluminum alloy subjected to pre-hardening forming

The combined effect of pre-aging and Mg/Si ratio on the natural aging and bake hardening in Al-Mg-Si-0.7Cu alloys

Experimental Study on Mechanical Behaviour of Friction Stir Welded Aluminium Alloy Butt Joints

Effect of post-weld heat treatment on microstructure and mechanical properties of 7055 aluminum alloy electron beam welded joint

The Effect of Bake Hardening on Quenched and Partitioned AISI 420 Stainless Steel

Effect of softening of 6082-T6 aluminum alloy CMT welded joints on mechanical properties and fracture behavior

Microstructure and microhardness of aluminium alloy friction stir welds with heat treatment

Effect of heat treatment on the microstructure and mechanical properties of spray formed 7055 aluminum alloy TIG welded joints reinforced by ZrB 2 / Al 3 (Sc, Zr) particles

Effects of Post-weld Heat Treatment on Microstructure, Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

Study on the Effect of Heat Treatment on Microstructures and High Temperature Mechanical Properties of Welding Spots of Hot Stamped Ultra-High Strength Steel Patchwork Blanks

The Effect of Adding V and Nb Microalloy Elements on the Bake Hardening Properties of ULC Steel before and after Annealing

Influence of Pre-strain on the Mechanical Properties of A6111-T4P Sheet with Bake Hardening

Effect of surface treatments and storage conditions on resistance spot weldability of aluminum alloy 5182

Importance of Hardening Effect and Its Analysis on Diametrical Fractured Ends of Tensile Testing of Al and Steel

The Influence of Cold Forming and Heat Treatment Processes on the Mechanical and Fracture Properties of AA6016 Aluminum Sheets

Effect of Local Post Weld Heat Treatment on Tensile Properties in Friction Stir Welded 2219-O Al Alloy

Combined Effect of Pre-Strain at Elevated Temperature and Pre-Aging on Aging Strength and Microstructures of AA6082