Abstract:The 2195 Al-Li alloy, as one of the representative third-generation Al-Li alloys, has extensive applications in lightweight aerospace structures. In this paper, the anisotropy in mechanical properties and microstructure evolution of 2195 Al-Li alloy sheets were investigated under a strain rate of 0.01, 0.1, 1 s-1 and a temperature of 440 and 500 °C. Experimental results showed that the hot tensile properties of the 2195 Al-Li alloy sheet exhibited a strong dependence on loading directions. The peak stress (PS) and elongation (EL) along the rolling direction (RD) were larger than the transverse direction (TD). For the tests carried out at 440 °C-1 s-1, the PS values of the sheets stretched along the RD and TD are 142.9 MPa and 110.2 MPa, respectively. And, most of the PS anisotropy values are larger than 15%. The anisotropy in EL is less significant than in PS. All the differences are about 10%. Moreover, dimples in the samples stretched along RD were more and deeper than those along TD at 440 °C. The fracture morphology along RD and TD were similar, and both were cleavage fractures at 500 °C. Particularly, the fractions of high angle grain boundaries (HAGBs) along TD were all about 5% larger than those of RD. And, there were more small-sized continuous dynamic recrystallization (CDRX) grains inside the initial grains and discontinuous dynamic recrystallization (DDRX) grains featured with the local bulge of grain boundaries along TD. This was due to the smaller average Schmid factor and the vertical EL trend of the initial grains when the samples were stretched along TD. A model of grain evolution during the dynamic recrystallization (DRX) along RD and TD was proposed based on EBSD results. The Schmid factor and banded structure had a more prominent effect on the hot ductility of the 2195 Al-Li alloy compared with the degree of DRX, thus presenting a higher EL and better hot ductility along RD.

Influence of Pre-strain on the Mechanical Properties of A6111-T4P Sheet with Bake Hardening

Influence of Pre-Straining and Heating on Strain-Rate Sensitivity of AA5182-O

The Influence of Cold Forming and Heat Treatment Processes on the Mechanical and Fracture Properties of AA6016 Aluminum Sheets

Effects of pre-stretching and baking treatment on microstructural evolution and mechanical properties of 7A09 aluminum alloy subjected to pre-hardening forming

Combined Effect of Pre-Strain at Elevated Temperature and Pre-Aging on Aging Strength and Microstructures of AA6082

Effect of Pre-Strain on Microstructure and Stamping Ability of TA2 Titanium Alloy and H260 Low-Alloy Steel

Effect of Pre-Deformation on Microstructure and Mechanical Properties of 2219 Aluminum Alloy Sheet by Thermomechanical Treatment

Strain Hardening under Large Deformation for AA5182

The Effect of Hot Forming–Quenching and Heat Treatment Processes on the Mechanical Properties of AA6016 Aluminum Alloy Sheets

Effect of Pre-Stretch on the Precipitation Behavior and the Mechanical Properties of 2219 Al Alloy

Flow Stress Curve Modeling of Bake-Hardening A6111 Aluminum Alloy

Effect of Prestrain on Microstructure and Mechanical Behavior of Aged Ti–10V–2Fe–3Al Alloy

Revealing the Role of Pre-Strain on the Microstructure and Mechanical Properties of a High-Mn Austenitic Steel

Identification of forming performance parameters for 6016 aluminum alloy sheet under different strain paths via digital image correlation technology

Modeling the Effect of Pre-Straining on Mechanical Behavior of Magnesium Alloy Sheet

Effect of annealing process on microstructure and mechanical properties of precipitated phase of A1235 aluminum alloy

Effect of Pre-aging Technology on Microstructure and Mechanical Properties of 6111 Aluminum Alloy

Effect of large pre-deformation on the microstructure, texture and mechanical properties of Al-Zn-Mg alloy extruded profiles

Bending Properties and Deformation Micromechanisms of Near-Α Titanium Alloy Sheets/foils Considering Initial Texture Characteristics and Size Effect

Effects of Pre‐Strain on the Microstructural Evolution and Mechanical Strength of in Situ TiB2/7050 Al Composite

Effect of Initial Orientation on the Anisotropy in Microstructure and Mechanical Properties of 2195 Al-Li Alloy Sheet during Hot Tensile Deformation