Abstract:Fusion welding is extensively used for joining structural assemblies, especially those with complex geometries. However, it often results in heat-affected zones (HAZ) that are, in most cases, softer than other regions around and beyond the weld area. Coupling both experiment and thermodynamic modeling—electron microscopy, x-ray microscopy (XRM), and CALculation of PHAse Diagrams (CALPHAD)—we re-examine the origin of softening in tungsten inert gas (TIG)-welded heat-treatable AA 6061-T651 for a more comprehensive understanding of its (softening) evolution. This study reveals material softening up to at least 38 mm away from the weld center, and partitioned heat-affected zones—HAZ1, HAZ2, HAZ3, and HAZ4—based on peak temperature, associated hardness, and precipitate phases in these zones. Analytical modeling and thermodynamic simulation predict solid solution and further precipitation of coherent GP zones in HAZ1, while coarsening of pre-existing precipitate occurs in HAZ2 (non-coherent/stable β -Mg 2 Si), HAZ3 (both semi-coherent/metastable β ′ and coherent/metastable β ′′) and HAZ4 (coherent/metastable β ′′). These welding-induced transformations—origin of softening—result in non-homogenous hardness in the zones compared to the unaffected base material (120 HV): HAZ1 to HAZ4 are 66-72, 54-64, 64-94, and 95-106 HV, respectively. Under tensile load, the TIG-welded sample fractures at the softest region—HAZ2. Additionally, XRM analysis confirms the presence of porosity in the welded area and its closure during plastic deformation, so that the severity of softening has a greater influence on localized fracture than the presence of porosity in the weld area. This work shows that new solid-state welding technologies that minimize nanostructural changes in base materials, especially precipitation-hardened alloys, should be sought.

Effect of softening of 6082-T6 aluminum alloy CMT welded joints on mechanical properties and fracture behavior

Strength calculation and microstructure characterization of HAZ softening area in 6082-T6 aluminum alloy CMT welded joints

Mechanical Properties and Failure Mechanisms of Friction Stir Spot Welds of AA 6061-T4 Sheets

Microstructural evolution and its effect on mechanical properties in different regions of 2219-C10S aluminum alloy TIG-welded joint

Microstructure and Failure Mechanisms of Refill Friction Stir Spot Welded 7075-T6 Aluminum Alloy Joints

Dynamic Fracture Properties of 2024-T3 and 7075-T6 Aluminum Friction Stir Welded Joints with Different Welding Parameters

Investigating the Multiscale Effects of a Novel Post–weld Composite Processing Treatment on Minimizing Weld Softening in AA6061-T6 Al–alloy

Effect of aging state on microstructure and properties of heat affected zone in Al–Mg–Si–Cu alloy welded joints

Investigation of the Mesoscale Damage Evolution Process of AA5754O Aluminum Alloy CMT Welded Joints

X-ray Microscopic and Thermodynamic Model Assessments of Softening in TIG-Welded AA 6061-T651

Correlation Between Microstructure and Mechanical Properties of 2219-T8 Aluminum Alloy Joints by VPTIG Welding

Microstructure and abnormal mechanical properties under the coupling effect of strain and temperature for friction-stir-welded joints of Al-Mg-Si alloy

Effect of Rotation Speed on Microstructure Evolution and Mechanical Properties of Nugget Zone in 2195-T8 Al-Li Alloy Friction Stir Welding Joints

Studies on Softening Behavior and Mechanism of Heat-Affected Zone of Spray Formed 7055 Aluminum Alloy under TIG Welding

Study on the Morphology, Microstructure, and Properties of 6082-T6 Aluminum Alloy Joints in MIG Welding

Effects of Porosity, Heat Input and Post-Weld Heat Treatment on the Microstructure and Mechanical Properties of TIG Welded Joints of AA6082-T6

Mechanical Properties and Microstructure of 6082-T6 Aluminum Alloy Joints by Self-support Friction Stir Welding

Influence of welding residual stress and welding method on fracture properties of welded joints

Mechanical Properties and Their Relations to Microstructural Characteristics of High-Speed Friction Stir-Welded AA6005A-T6 Aluminum Hollow Extrusions

Microstructur and mechanical properties of the friction stir welded joint of 7020 aluminum alloy

Distribution of Tensile Property and Microstructure in Friction Stir Weld of 6063 Aluminum