Abstract:In cold spray, surficial oxide scale of the feedstock powder not only reduces the deposition efficiency of spraying powder, but also deteriorates the properties of the deposit due to its influence on inter-particle bonding. To simultaneously improve the deposition efficiency of spraying powder and the properties of the deposit, in this study, taking Cu as a typical material, acid pickling was used to remove the oxide scale on the surface of the as-received powder. During acid pickling, Cu powder particles were immersed into the acid alcohol solution and then dried in a low-pressure tank. Using the as-received powder and acid-pickled powder as the spraying powder, Cu deposits were prepared under the same spraying conditions. The deposition behavior of spraying powders, the microstructure and properties, including mechanical properties, conductivities and anti-corrosion behavior of the Cu deposits were systematically studied. Results show that acid pickling can effectively remove the oxide scale on the surface of the as-received powder and reduce the powder oxygen content from 0.12 wt% to 0.044 wt%, leading to an increase in deposition efficiency of the spraying powder from 74% to 84%. Although both the Cu deposits reveal dense microstructure and thereby show good anti-corrosion, the tensile properties and conductivities of Cu deposits, which are sensitive to the inter-particle bonding, decrease with increase of the oxygen content in spray powder. Cu deposit prepared by acid-pickled powder shows the superior tensile properties and conductivities, and the tests yielded the tensile strength of 245 MPa, Young modulus of 85 GPa, electrical and thermal conductivities of 90%IACS and 298 W·m−1·K−1. Therefore, it is an effective approach to improve the deposition efficiency of spraying powder and prepare high-property cold-sprayed metallic deposit simultaneously by using acid pickling to remove the surficial oxide scale of particle.

Dependency of Deposition Behavior, Microstructure and Properties of Cold Sprayed Cu on Morphology and Porosity of the Powder

Comparative Analysis of Microstructural and Mechanical Attributes in Low-Pressure Cold-Spray Coatings: Impact of Varied Cu Feedstock Powders

A New Approach to Prepare Fully Dense Cu with High Conductivities and Anti-Corrosion Performance by Cold Spray

Influence of Feedstock in the Formation Mechanism of Cold-Sprayed Copper Coatings

A Comparison of Cold Spray Deposition Behavior Between Gas Atomized and Dendritic Porous Electrolytic Ni Powders under the Same Spray Conditions

Effect of Spray Conditions on Deposition Behavior and Microstructure of Cold Sprayed Ni Coatings Sprayed with a Porous Electrolytic Ni Powder

Microstructure and Properties of Cu–Cr Coatings Deposited by Cold Spraying

Correlating Particle Impact Condition with Microstructure and Properties of the Cold-Sprayed Metallic Deposits

Microstructure and Property of Micro-Plasma-sprayed Cu Coating

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Improving deposition efficiency and inter-particle bonding of cold sprayed Cu through removing the surficial oxide scale of the feedstock powder

Influence of Different Copper Feedstock Powders on the Microstructure and Corrosion Resistance of Coatings Prepared by Cold Gas Spray

Effect of Interfacial Structure on Microstructure and Properties of Cold-Sprayed Cu-Al2O3 Composite Coating

Microstructure and properties of copper coating by using plasma‐assisted low‐pressure cold spray

Microstructure and Property of Cold Sprayed Copper Coating

Microstructure, mechanical properties, and cavitation erosion performances of cold sprayed CuZn35 coatings

Texture and grain boundary engineering in electrodeposited SnCu coatings and its effect on coating corrosion behaviour

Microstructure Evolution of Cold-Sprayed Coating During Deposition and Through Post-Spraying Heat Treatment

Microstructural Analysis of Gas Atomized Al-Cu Alloy Feedstock Powders for Cold Spray Deposition

Study on cold sprayed Ag-Cu alloy coating

Impact of Microstructural Anisotropy of As-Cold-Sprayed Cu Deposits on Its Annealing Effect