Abstract:As technology has developed along with the increasing mechanical demands placed upon it, the need for fatigue exceeding 107 cycles or even longer for machines and components is necessary, not only for safety and reliability, but also for minimizing the economic and human costs brought about by failure. Titanium alloys have been one of the most widely used and most important materials in the aerospace domain owing to their superior properties of high strength-weight ratio and good temperature resistance. Studies have shown that S-N curves of TC4 alloy exhibit a linearly decreasing tendency and no fatigue limit around 107 cycles under very highcycle fatigue. Thus, fatigue strength design according to the traditional standard is adventurous to some extent. In this study, an electromagnetic resonant fatigue testing machine at a frequency of 100 Hz was employed to carry out fatigue tests and investigate the influence of two stress ratios (R = 0. 1 and-1) on TC4 titanium alloy under a very high-cycle fatigue regime. The results show that S-N curves under each of the two stress ratios present the so called"duplex characteristic"while their respective failure mechanisms are different. The fracture of specimens under R = 0. 1 corresponds to two modes, i. e., surface failure induced by machining defects, and interior fisheye failure, accompanied by the appearance of facets. The horizontal part of the S-N curve at stress ratio of 0. 1 represents the transition stress between the surface failure and the interior failure, beyond which the surface failure can take place, while surface failure without facets only occurs under R =-1. Based on fracture mechanics, the threshold value of small crack growth is lower under a positive stress ratio and in a vacuum, which is more conducive to crack propagation and formation of facets. From these results, the interior fatigue failure process and mechanism of TC4 titanium can be explained as follows: (1) the appearance of slip lines or bands inpartial α grain; (2) initiation and coalescence of micro-crack; (3) formation of granular bright facets (GBF); (4) formation of fisheye; (5) unstable crack propagation outside the fisheye; (6) instantaneous fracture.

Very High Cycle Fatigue of TC4 Titanium Alloy under Variable Stress Ratio: Failure Mechanism and Life Prediction

Low-cycle Fatigue Behavior and Life Prediction of TA15 Titanium Alloy by Crystal Plasticity-Based Modelling

Low-cycle Fatigue Behavior and Property of TA15 Titanium Alloy with Tri-Modal Microstructure

Fatigue cracking behavior and life assessment of TC11 titanium alloy in very high cycle regime at two working temperatures

Crack Initiation and Early Growth Behavior of TC4 Titanium Alloy under High Cycle Fatigue and Very High Cycle Fatigue

Subsurface Crack Nucleation and Growth Behavior and Energy-Based Life Prediction of a Titanium Alloy in High-Cycle and Very-High-cycle Regimes

Effect of Stress Ratio on the Very High-Cycle Fatigue Failure Mechanism of TC4 Titanium Alloy

Microstructure based cracking behavior and life assessment of titanium alloy under very-high-cycle fatigue with elevated temperatures

High Cycle Fatigue Life Prediction on TC4 Titanium Alloy after Overload Treatment

Experimental Study on Forged TC4 Titanium Alloy Fatigue Properties under Three-Point Bending and Life Prediction

Life Prediction and Failure Analysis in Laser Powder Bed Fused TiC/Ti6Al4V Titanium Matrix Composite under High Cycle and Very High Cycle Fatigue Conditions

Fatigue Crack-Initiation Mechanisms of a Dual-Phase Titanium Alloy Exhibiting High Tensile and High-Cycle Fatigue Properties

Fatigue Crack Growth of TC17 Titanium Alloy with Three Microstructures

High cycle and very high cycle fatigue of TC17 titanium alloy: Stress ratio effect and fatigue strength modeling

Low Cycle Fatigue Properties of Linear Friction Welded Joint of TC11 and TC17 Titanium Alloys

Cyclic Deformation and Microcrack Initiation During Stress Controlled High Cycle Fatigue of a Titanium Alloy

Subsurface Facet-fisheye Induced Failure of Titanium Alloy under Very High Cycle Fatigue

Fatigue property and failure mechanism of TC4 titanium alloy in the HCF and VHCF region considering different forging processes

Subsurface Facets-Induced Crack Nucleation Behavior and Microstructure-Based Strength Evaluation of Titanium Alloys in Ultra-Long Life Regime

Prediction of Fatigue Life of TC4 Titanium Alloy Based on Normalized Equivalent Initial Flaw Size Model

Faceted Crack Induced Failure Behavior and Micro-Crack Growth Based Strength Evaluation of Titanium Alloys under Very High Cycle Fatigue